Polyaniline-decorated Macadamia nutshell composite: an adsorbent for the removal of highly toxic Cr(VI) and efficient catalytic activity of the spent adsorbent for reuse

Preparation and Performance Study of Boron Adsorbent from Plasma-Grafted Polypropylene Melt-Blown Fibers

In this study, the plasma graft polymerization technique was used to graft glycidyl methacrylate (GMA) onto polypropylene (PP) melt-blown fibers, which were subsequently aminated with N-methyl-D-glucamine (NMDG) by a ring-opening reaction, resulting in the formation of a boron adsorbent denoted as PP-g-GMA-NMDG. The optimal conditions for GMA concentration, grafting time, grafting temperature, and the quantity of NMDG were determined using both single factor testing and orthogonal testing. These experiments determined the optimal process conditions to achieve a high boron adsorption capacity of PP-g-GMA-NMDG. Fourier-transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), energy dispersion spectrum analysis (EDS), and water contact angle measurements were performed to characterize the prepared adsorbent. Boron adsorption experiments were carried out to investigate the effects of pH, time, temperature, and boron concentration on the boron adsorption capacity of PP-g-GMA-NMDG. The adsorption isotherms and kinetics of PP-g-GMA-NMDG for boron were also studied. The results demonstrated that the adsorption process followed a pseudo-second-order kinetic model and a Langmuir isothermal model. At a pH of 6, the maximum saturation adsorption capacity of PP-g-GMA-NMDG for boron was 18.03 ± 1 mg/g. In addition, PP-g-GMA-NMDG also showed excellent selectivity for the adsorption of boron in the presence of other cations, such as Na+, Mg2+, and Ca2+, PP-g-GMA-NMDG, and exhibited excellent selectivity towards boron adsorption. These results indicated that the technique of preparing PP-g-GMA-NMDG is both viable and environmentally benign. The PP-g-GMA-NMDG that was made has better qualities than other similar adsorbents. It has a high adsorption capacity, great selectivity, reliable repeatability, and easy recovery. These advantages indicated that the adsorbents have significant potential for widespread application in the separation of boron in water.

Hyperbranched-Polyethylenimine-Functionalized Coal Fly Ash as an Adsorbent for the Removal of Hexavalent Chromium and Reuse as a Dye Photocatalyst

Coal fly ash (CFA) has been extensively researched as an adsorbent for heavy metals, but its application is limited by its low adsorption capacity. The modification of CFA with hyperbranched polymers results in improved adsorption capacities. Hyperbranched polyethylenimine (HPEI) is a hyperbranched polymer containing NH2 groups that can bind with heavy metal ions through complexation or electrostatic interactions. In this study, CFA-HPEI adsorbents with various HPEI loadings (1-5%) were prepared and evaluated for the removal of Cr(VI). The successful incorporation of HPEI onto CFA was confirmed using Fourier transform infrared, elemental analysis, and X-ray photoelectron spectroscopy (XPS). The 3% CFA-HPEI loaded adsorbent resulted in optimum results when the effect of pH and adsorbent dosage was studied. The pseudo-second-order kinetics model best described the adsorption kinetics at an initial concentration of 20 mg/L. The Freundlich adsorption isotherm model best fitted the equilibrium adsorption data with a maximum adsorption capacity of 85.93 mg/g. The Cr-loaded adsorbent was reused as a photocatalyst to degrade methylene blue (MB) in the presence of visible light. The loaded adsorbent degraded 98.9% of MB (5 mg/L) within 180 min and was accompanied by compounds with m/z of 173 and 234, corresponding to the intermediate degradation of Azure A. The XPS analysis confirmed the coexistence of Cr(III) and Cr(VI) on the surface of the adsorbent. In addition, the loaded adsorbent exhibited good stability following MB degradation with no structural changes observed. Thus, CFA-HPEI adsorbents can be utilized as low-cost adsorbents for the remediation of toxic Cr(VI) from water and wastewater. The Cr-loaded CFA-HPEI adsorbent can be effectively reused as a photocatalyst, thus reducing environmental pollution.

Boron Adsorption Using NMDG-Modified Polypropylene Melt-Blown Fibers Induced by Ultraviolet Grafting

Boron is in high demand in many sectors, yet there are significant flaws in current boron resource utilization. This study describes the synthesis of a boron adsorbent based on polypropylene (PP) melt-blown fiber using ultraviolet (UV)-induced grafting of Glycidyl methacrylate (GMA) onto PP melt-blown fiber, followed by an epoxy ring-opening reaction with N-methyl-D-glucosamine (NMDG). Using single-factor studies, grafting conditions such as the GMA concentration, benzophenone dose, and grafting duration were optimized. Fourier transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), X-ray diffraction (XRD), and water contact angle were used to characterize the produced adsorbent (PP-g-GMA-NMDG). The PP-g-GMA-NMDG adsorption process was examined by fitting the data with different adsorption settings and models. The results demonstrated that the adsorption process was compatible with the pseudo-second-order model and the Langmuir model; however, the internal diffusion model suggested that the process was impacted by both extra- and intra-membrane diffusion. According to thermodynamic simulations, the adsorption process was exothermic. At pH 6, the greatest saturation adsorption capacity to boron was 41.65 mg·g^-1 for PP-g-GMA-NMDG. The PP-g-GMA-NMDG preparation process is a feasible and environmentally friendly route, and the prepared PP-g-GMA-NMDG has the advantages of high adsorption capacity, outstanding selectivity, good reproducibility, and easy recovery when compared to similar adsorbents, indicating that the reported adsorbent is promising for boron separation from water.