Bioactivity and cell viability of Ag+- and Zr4+-co-doped biphasic calcium phosphate

Silver phosphate-modified carbonate apatite honeycomb scaffolds for anti-infective and pigmentation-free bone tissue engineering

Bone regeneration using synthetic materials has a high rate of surgical site infection, resulting in severe pain for patients and often requiring revision surgery. We propose Ag3PO4-based surface modification and structural control of scaffolds for preventing infections in bone regeneration. We demonstrated the differences in toxicity and antibacterial activity between in vitro and in vivo studies and determined the optimal silver content in terms of overall anti-infection effects, bone regeneration, toxicity, and pigmentation. A honeycomb structure comprising osteoconductive and resorbable carbonate apatite (CAp) was used as the base scaffold. CAp in the scaffold surface was partially replaced with different concentrations of Ag3PO4 via controlled dissolution-precipitation reactions in an AgNO3 solution. Both bone regeneration and infection prevention were achieved at 860-2300 ppm of silver. Despite the absence of Ag3PO4, honeycomb scaffolds were less susceptible to infection, even under conditions where infection occurs in clinically used three-dimensional porous scaffolds. Regardless of in vitro cytotoxicity at >5200 ppm of silver, increasing the silver content to 21,000 ppm did not adversely affect in vivo bone formation and scaffold resorption or cause acute systemic toxicity. Rather, bone formation was enhanced with 5200 ppm of silver. However, pigmentation was observed at that concentration. Hence, we concluded that the optimal silver concentration range is 860-2300 ppm for anti-infective and pigmentation-free bone regeneration. Bone regeneration was achieved via surface modification, resulting in the rapid release of silver ions immediately after implantation, followed by gradual release over several months. The scaffold structure may also aid in preventing bacterial growth within the scaffolds.

Synthesis and characterization of hydroxyapatite nanoparticles from calcium hydroxide fouled with gases evolved from smokestack of glass industry

In glass industry, the evolved gases and fumes from burning the gas fuel absorbed in calcium hydroxide to minimize the pollution of environment. After a period of time, the calcium hydroxide fouled with sulphate and carbonate as action of the absorbed SO3 and CO2 gases. Based on our interest to treatment the solid waste materials, this study intended to convert the obtained waste of calcium hydroxide fouled with gases to valuable products. Firstly, this waste was treated with water, caustic soda and acids. The results confirmed the conversion of waste to pure calcium sulfate by treatment with 6 v/v% sulfuric acid. Secondly, the obtained calcium sulfate was reacted with ammonium dihydrogen phosphate solution for preparation of calcium hydroxyapatite (HAp) nanoparticles. The produced HAp sample was characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM) and scanning electron microscopy (SEM), thermal gravimetric analysis (TGA) and N2 adsorption measurements. The obtained findings confirmed that the HAp can be produced after calcination at 700 °C, nanorods-like of sizes ranged from 11 to 15 nm and with main surface functional groups of hydroxyapatite. TGA and DTA data indicated that HAp is thermally stable up to 700 °C. Also, the obtained HAp has Ca/P molar ratio of 1.60 and exhibited high total surface area of 146 m2/g with mesoporous structure which make this material can be used in medical and water purification applications.

Doxorubicin loaded cerium substituted hydroxyapatite nanoparticles: A promising new therapeutic approach for bone regeneration, doxorubicin delivery, and cancer treatment

The current study used the precipitation method to prepare pure calcium hydroxyapatite (HA) and cerium-substituted hydroxyapatite (Ce-HA) nanoparticles, where cerium ions were exchanged into the HA structure at different concentrations ranging from 3 to 7 wt%. X-ray powder diffraction (XRD), field emission scanning electron microscopy (FE-SEM), high resolution transmission electron microscopy (HR-TEM), Fourier transform infrared (FTIR) spectroscopy, Brunauer-Emmett-Teller (BET) surface area measurements, and zeta potential were used to examine the structural characteristics of the nanoparticles. Additionally, the antibacterial and antifungal effects of the produced materials on Gram-positive, Gram-negative, and fungal bacterial species were studied. Nanoparticles with cerium doping showed effective antibacterial and antifungal properties. All samples were tested for bioactivity in simulated body fluid (SBF), and the formation of an apatite layer on their surfaces was highlighted using SEM in conjunction with energy-dispersive X-rays (EDX).Doxorubicin (DOX) release from Ce-HA nanoparticles and pure HA was tested in phosphate-buffered saline (PBS) for up to 28 days. Both nanoparticles were able to release the drug while still being semi-fully loaded. Similarly, the cytotoxic effect of all produced samples on the MG-63 cell line was evaluated, and all samples showed good cytocompatibility. The cytotoxic effect of doxorubicin-loaded nanoparticles showed promising anticancer activity against bone cancer cells, especially samples with high cerium content. The resulting nanoparticles show excellent promising ability for the delivery of doxorubicin to bone cancer with the capacity for bone regeneration.

Development of high performance microwave absorption modified epoxy coatings based on nano-ferrites

With the rapid spread of wireless technologies and increasing electromagnetic energy, electromagnetic waves (EMW) have become a severe threat to human health. Therefore, minimizing the harmful effects of electromagnetic wave radiation is possible through the development of high-efficiency EMW absorption coatings. The aim of this work was to generate microwave absorbance coatings containing synthesized nano-CuFe2O4 and nano-CaFe2O4. Firstly, nano-CuFe2O4 and nano-CaFe2O4 were synthesized using the sol-gel method. Then, their structure, electrical, dielectric, and magnetic properties were investigated to find out the possibility of using these materials in high-frequency applications (e.g., microwave absorbance coatings). After that, two dosages (2.5 wt% and 5 wt%) of nano-CuFe2O4 and nano-CaFe2O4 were incorporated into epoxy resin to prepare modified epoxy resin as microwave coatings. The dielectric studies show that the AC conductivity of the prepared samples is high at high frequencies. Additionally, the magnetic properties reveal a low coercivity value, making these samples suitable for high-frequency devices. The microwave results illustrate that adding nano-ferrites with high content enhances the absorption characteristics of the tested films. The results showed that the two films have two absorption bands with RL < -10 dB ranging from 10.61 to 10.97 GHz and from 10.25 to 11.2 GHz. The minimum return loss achieved for the two cases is -13 and -16 dB, respectively. Indicating that the film coated with CuFe has a better absorption value than the one coated with CaFe.

Influence of the addition of different metal oxides on physicochemical and biological properties of calcium fluorosilicate/PCL bone cement

Calcium silicate cements have been greatly developed in the last decades through different approaches. Among these approaches, the inclusion of antibacterial agents or addition of metal oxides. Herein, calcium silicate cement containing fluorine (CFS) was developed from sodium fluorosilicate precursor for the first time using chemical perception method. Afterwards, metal oxide Bi2O3 or MgO or ZrO2 was individually mixed with CFS powder and blended together using Polycaprolactone polymer (PCL). The cement mixtures were characterized using DSC, XRD, FTIR and SEM/EDX to determine the effect of metal oxide on the pure CFS. Furthermore, mechanical, antibacterial and cell viability properties were evaluated for the developed CFS mixture cements. Moreover, these CFS mixture cements were implanted in male Wistar rats to determine the effect of metal oxides on the rate of bone reformation. The findings of physicochemical and morphological characterization showed no remarkable effects on the pure CFS after mixing with each metal oxide. However, enhanced compressive strengths (up to 104.07N/cm2), antibacterial activity and cell viability (up to 96%) were achieved for the CFS cement mixtures. Finally, the in vivo studies confirmed the biocompatibility of the CFS cement mixtures and especially those mixed with Bi2O3 or ZrO2. Therefore, this study supports that CFS blends with Bi2O3 or ZrO2 can be novel promising cementing materials for bone restoration.

Biphasic calcium phosphate doped with zirconia nanoparticles for reconstruction of induced mandibular defects in dogs: cone-beam computed tomographic and histopathologic evaluation

The present study aimed to evaluate osteogenic potential and biocompatibility of combining biphasic calcium phosphate with zirconia nanoparticles (4Zr TCP/HA) compared to biphasic calcium phosphate (TCP/HA) for reconstruction of induced mandibular defects in dog model. TCP/HA and 4Zr TCP/HA scaffolds were prepared. Morphological, physicochemical, antibacterial, cytocompatibility characterization were tested. In vivo application was performed in 12 dogs where three critical-sized mandibular defects were created in each dog. Bone defects were randomly allocated into: control, TCP/HA, and 4Zr TCP/HA groups. Bone density and bone area percentage were evaluated at 12 weeks using cone-beam computed tomographic, histopathologic, histomorphometric examination. Bone area density was statistically increased (p < 0.001) in TCP/HA and 4Zr TCP/HA groups compared to control group both in sagittal and coronal views. Comparing TCP/HA and 4Zr TCP/HA groups, the increase in bone area density was statistically significant in coronal view (p = 0.002) and sagittal view (p = 0.05). Histopathologic sections of TCP/HA group demonstrated incomplete filling of the defect with osteoid tissue. Doping with zirconia (4Zr TCP/HA group), resulted in statistically significant increase (p < 0.001) in bone formation (as indicated by bone area percentage) and maturation (as confirmed by Masson trichrome staining) compared to TCP/HA group. The newly formed bone was mature and organized with more trabecular thickness and less trabecular space in between. Physicochemical, morphological and bactericidal properties of combining zirconia and TCP/HA were improved. Combining zirconia and TCP/HA resulted in synergistic action with effective osteoinduction, osteoconduction and osteointegration suggesting its suitability to restore damaged bone in clinical practice.

Formulation and evaluation of alginate-gelatin hydrogel scaffolds loaded with zinc-doped hydroxyapatite and 5-fluorouracil

Alginate and gelatin are natural macromolecules used to formulate biocompatible drug delivery systems. Hydroxyapatite (HA) is an osteophilic ceramic used to prepare bone scaffolds. The current study aimed at preparing and characterizing HA, zinc-doped HA, and 5-fluorouracil(5-FU)-loaded alginate-gelatin-based hydrogel scaffolds using different crosslinking solutions. 5-FU incorporation efficiency, in-vitro drug release, antitumor bioassays, FTIR, X-ray-diffraction (XRD), High-Resolution Transmission, and Scanning-Electron Microscope (HR-TEM and SEM) studies were conducted. XRD showed the incorporation of Zn²⁺ into HA structure with a deformity in HA crystal lattice and inhibited crystal growth. FTIR-spectra represented the characteristic bands corresponding to HA structure. HR-TEM showed a decreased HA crystal size and rod-like crystallites that increased with increasing zinc content. Zn²⁺ content and 5-FU-loading caused significant effects on the scaffolds' thickness (p-value = 0.021 and 0.035, respectively). Burst 5-FU release within 10-15 min followed by 100 % release within 4 h was observed. Zinc content showed a significant positive effect on the cytotoxicity% of the blank and drug-loaded scaffolds. XRD and FTIR studies revealed that 5-FU was completely incorporated into the hydrogel with no chemical interaction. SEM-imaging showed interconnected pores and needle-shaped drug particles. The prepared formulations showed promising physico-chemical properties for targeted delivery of 5-FU in the form of biocompatible bone scaffolds.

Zn-containing Wollastonite with Well-defined Microstructural and Good Antifungal Activity.. [DOI: 10.21203/rs.3.rs-2184143/v1] [Citation(s) in RCA: 0] [Impact Index Per Article: 0]

Antimicrobial and antifungal materials we prepared from Zn-containing wollastonite set by wet precipitation method. Wollastonite, hardystonite, willemite and very little quartz were developed after sintering at 1100°C/2h, however, the Raman spectroscopy approved the later phases by their characteristic Raman shift bands. The microstructure exhibited accumulated rounded to irregular clusters containing nano-size particles (< 500nm) developed in all sintered samples. Zeta potential; exposed negative values for all powdered samples from − 2.64 to -17.6 mV (i.e., for Zn-free to highest Zn-containing samples). It can be easily noticed that the lowest ZnO-content exhibits a varied range of antibacterial activities in contrast to Gram-negative (E. coli) and Gram-positive (S. aureus & B. subtilis). Correspondingly, the CZS5 exhibits good inhibitory effect against the filamentous pathogenic fungus (A. niger).