[Motion artifacts in the vitreous body during vitrectomy]

A promising approach in laser vitrectomy executed by plasma-mediated removal of vitreous body via a diode-pumped Q-switched Nd:YAG laser

To examine the applicability of plasma-mediated vitreous body removal, a diode-pumped Q-switched Neodymium:YAG laser was used for a possible application in eye surgery/vitrectomy. On a total of 1500 porcine vitreous bodies, removal rates were evaluated by comparing different LaserVit-tip designs (Mark I/II Gauge 19 and Mark III Gauge 22). The Nd:YAG laser, operating at a wavelength of 1064 nm and a pulse duration of 4 ns, was utilized for vitreous body removal with respective settings of 2, 3 and 4 mJ and pulse repetition rates (cut rates) from 5 to 25 Hz (300–1500 /min) in 5 Hz-steps as well as for 100 Hz (6000 cuts/min). The exposure times were selected at 10, 20, 40 and 60 s, respectively. Comparative measurements were carried out with mechanical cutters (Gauge 20 and Gauge 23), applying a fixed cut rate of 800 /min (13.33 Hz) at identical exposure times. The LaserVit-tips showed successful vitreous body removal for all laser settings and exposure times (Mark I: 6.2 g/min, Mark II: 8.2 g/min at 1500 cuts/min and 3 mJ, Mark II: 10.1 g/min, Mark III: 3.6 g/min at 6000 cuts/min at 3 mJ). Similar tip-dimensions (Gauge 22_laser and Gauge 23_cutter) showed comparable removal rates of 3.6 g/min_laser and 1.3 g/min_cutter with settings of 6000 cuts/min at 3 mJ (laser) and 800 cuts/min for the mechanical cutter. A diode-pumped Q-switched Nd:YAG laser can successfully and gently remove vitreous body. The efficiency of the laser was comparable to that of mechanical cutters in terms of quantity of material removed per time unit.

Erbium: yttrium-aluminum-garnet laser induced vapor bubbles as a function of the quartz fiber tip geometry

BACKGROUND

The use of modern erbium: yttrium-aluminum-garnet (YAG) laser systems in opthalmic microsurgery requires a precise knowledge of the size and dynamics of the laser induced vapor bubbles. The aim of this work was to clarify the possibilities of controlling the vapor bubble shape and size by using an optimized fiber tip geometry for various ophthalmic applications with the erbium: YAG laser.

METHODS

The mid-infrared radiation of free-running erbium: YAG laser was coupled optically into means of different low OH(-) quartz fiber tips to investigate the vapor bubble formation in water by high-speed photography. The core diameter of four fiber tips ranged from 200 up to 940 microm. Fourteen fiber tips were polished at an angle graduated from 10 degrees to 70 degrees over the full core diameter (seven fiber tips) and over the half core diameter (seven fiber tips). Three fiber tips were produced to have a curvature at the distal end with curvature radii of 160, 230, and 420 microm.

RESULTS

The shape as well as the size of erbium: YAG laser induced vapor bubbles can be controlled systematically by using adequate fiber tip geometries. In detail, the used different angles and curvatures demonstrate that the propagation direction of the vapor bubbles can be estimated by optical modeling considering Snell's law and the Fresnel laws at a quartz-air boundary. Beside this, the size of a vapor bubble can be predetermined by choosing ideal fiber tip geometries to reduce or increase the radiant exposure at the distal end of the quartz fiber tip.

CONCLUSIONS

The good possibility of controlling the shape and size of vapor bubbles offers a wider range of new applications, especially in ophthalmic microsurgery such as erbium YAG laser vitrectomy.