Adsorption of metanil yellow from aqueous solution using polyaniline-bentonite composite

Water Hyacinth Leaves Are an Efficient, Green, and Cost-Effective Biosorbent for the Removal of Metanil Yellow from Aqueous Solution: Kinetics, Isotherm, and Thermodynamic Studies

Excessive water hyacinth growth in aquatic environments and metanil yellow (MY) dye in industrial wastewater pose severe environmental and public health challenges. Therefore, this study evaluated the effects of various process factors on batch MY biosorption onto water hyacinth leaves (LECs) and MY biosorption kinetics, equilibrium, and thermodynamics. The optimal pH for MY biosorption by LECs was 1.5-2.0. The initial MY concentration affected the equilibrium MY biosorption capacity but not the LEC particle size and solution temperature. However, the LEC particle size and solution temperature affected the MY biosorption rate; the biosorption rate was higher at a lower particle size (0.15-0.3 mm) and a higher temperature (62 °C) than at higher particle sizes and lower temperatures. The pseudo-second-order model adequately described the biosorption kinetics of MY by LECs at the different levels of the process factors, whereas the Sips and Redlich-Peterson models satisfactorily represented the biosorption isotherm of MY. The Sips model predicted a maximum MY biosorption capacity of 170.8 mg g-1. The biosorption of MY by LECs was endothermic and not spontaneous. These findings demonstrate that LECs exhibit great potential for bioremediating MY-contaminated wastewater, thereby providing valuable insights for effective water treatment and pollution control strategies.

Resource Recycling Utilization of Distillers Grains for Preparing Cationic Quaternary Ammonium—Ammonium Material and Adsorption of Acid Yellow 11

Using distillers grains (DG) as raw material after pre-treatment with sodium hydroxide (NaOH) and modified with cationic etherification agent 3-chloro-2-hydroxypropyltrimethylammonium chloride (CHPTAC), cationic quaternary ammonium distillers grains adsorption material (CDG) was successfully prepared. The optimal adsorption conditions were an adsorption temperature of 25 °C, adsorption time of 180 min, amount of adsorbent at 8.5 g/L, initial dye concentration of 100 mg/L, and pH of dye solution 7.0. The structure of CDG was characterized by FTIR, EDS, SEM, BET, ultraviolet spectrum analysis, and analysis of the zeta potential, while the adsorption mechanism was studied by adsorption kinetics, isotherms, and thermodynamics. The results showed that CHPTAC modified the distillers grains successfully and induced the formation of CDG with a large number of pore structures and good adsorption effect. The highest adsorption yield was above 98%, while after eight rounds of adsorption–desorption experiments, the adsorption rate was 81.80%. The adsorption mechanism showed that the adsorption process of acid yellow 11 (AY11) by CDG conforms to the pseudo-second-order kinetic model, mainly with chemical and physical adsorption such as pore adsorption and electrostatic adsorption. Thermodynamics conforms to the Freundlich isothermal model, and the adsorption process is a spontaneous, endothermic and entropy-increasing process.

Hexadecyltrimethylammonium Bromide Surfactant-Supported Silica Material for the Effective Adsorption of Metanil Yellow Dye

The adsorption behavior of an organic dye, metanil yellow (My), from water using micro-nano silica particles (MNSPs) was investigated. MCM-41-like (Mobil Composition of Matter No. 41) MNSPs were synthesized using tetraethoxy orthosilicate as a silica source and hexadecyltrimethylammonium bromide (CTAB) as a surfactant under basic conditions. Comparative studies were performed to assess the adsorption behaviors of the organic dye using the as-synthesized MCM-41 before the removal of CTAB and MCM-41, either after one, two, and three times of chemical etching or after calcination. My was adsorbed more effectively from water on the as-synthesized MCM-41 without the removal of the surfactant than on MCM-41 after the removal of the surfactant by chemical etching or calcination. In addition, MCM-41 after removing the surfactant by one-time chemical etching in the presence of hydrochloric acid also showed better adsorption of My from water than MCM-41 after removing the surfactant by further two and three times of chemical etching or calcination. For comparison, other kinds of dye molecules with different chemical structures such as methylene blue (Mb) and rhodamine B (Rb) were also used to check the possibility of adsorption of various dyes by the CTAB-supported MNSPs. To better understand the reason behind the adsorption phenomena, detailed studies on the kinetics and thermodynamics of adsorption of the MNSPs were performed. Excellent adsorption of My was observed at concentrations up to 100 mg L^-1 at 25 °C, whereas the adsorption was lower at higher concentrations of the My dye. Furthermore, enhanced My dye adsorption was observed at higher concentrations by increasing the adsorption temperature. It can be concluded that the MNSPs exhibited efficient adsorption of My, when the MNSPs are used without the removal of the surfactant and any further modifications, suggesting that the surfactant played key roles in the effective adsorption of the anionic dye. The as-synthesized MCM-41 was, however, not a good adsorbent for cationic dyes such as Mb and Rb.