Ten-year follow-up of a cemented tapered stem

Fully hydroxyapatite-coated compaction broached and triple-tapered stem may reduce the risk of stress shielding after primary total hip arthroplasty

PURPOSE

Changes in bone mineral density (BMD) around the fully hydroxyapatite (HA)-coated compaction broached and triple-tapered stem, namely, Polarstem, after total hip arthroplasty (THA) are currently unknown. Therefore, the aims of this study were to investigate clinical outcomes of Polarstem, mainly postoperative temporal changes in BMD around the stem for 2 years, and to compare them with those of HA-coated and non-HA-coated tapered-wedge stems.

METHODS

This retrospective cohort study enrolled 100 consecutive patients who underwent THA using Polarstem (n = 38), HA-coated Anthology (n = 31), and non-HA-coated Anthology (n = 31). BMD was evaluated using dual-energy X-ray absorptiometry in seven regions according to the Gruen zones. Postoperatively, BMD around the stem was assessed within 2 months (baseline BMD) and at 6, 12, and 24 months. A change in BMD was defined as the value calculated by dividing each postoperative BMD value at 6, 12, and 24 months by the baseline BMD value. Changes in BMD and radiographic parameters such as stress shielding and spot welds were compared among the three stems.

RESULTS

The incidence rate of stress shielding in the Polarstem group was significantly lower than those in the other two groups (p = 0.007). The change in BMD in Zone 7 of Polarstem was significantly more than that of the other two groups at 12 and 24 months postoperatively (p = 0.030 and p = 0.009, respectively).

CONCLUSION

Polarstem, a fully HA-coated compaction broached and triple-tapered stem, maintained BMD around the femoral calcar until 2 years postoperatively and could reduce the risk of stress shielding compared with tapered-wedge stems.

Functional Anatomy of the Hip Joint

BACKGROUND

The functional anatomy of the osteoarthritic hip joint in the sagittal plane has not been defined. The purpose of this study was to define the functional anatomy of the hip using clinical and radiographic analyses.

METHODS

320 hips had preoperative standing and sitting lateral spine-pelvis-hip X-rays. Radiographic pelvic measurements were pelvic incidence (PI) and sacral slope (SS), and hip measurements were anteinclination (AI) and pelvic femoral angle (PFA). Pelvic tilt (PT) was calculated as PI-SS. A triangle model was created from the clinical data that illustrates the functional motion of the hip during postural changes from standing to sitting.

RESULTS

Pelvic motion was coordinated with hip motion, even with spinopelvic imbalance and stiffness. Pelvic motion (ΔSS) varied for all 5 types of imbalance, but pelvic motion (ΔSS) and acetabular motion (ΔAI) changed with a 1:1 ratio and inversely with femoral motion (ΔPFA) with a 1:1 ratio. The triangle model showed similar results with ΔSS, ΔPT, and ΔAI changing in a 1:1:1 ratio, and femur motion inversely changing with a 1:1 ratio.

CONCLUSION

The functional anatomy of the hip joint can be visually illustrated using a triangle model. Pelvic angles SS, PT, and AI change in unison, whereas femoral motion (ΔPFA) changes inversely with pelvic motion (ΔSS) in a 1:1 ratio. This coordinated mobility explains the limitations of the Lewinnek safe zone, which include only the acetabulum.

Cementing of the hip arthroplasty stem increases load-to-failure force: a cadaveric study

Background and purpose - To date, there is not a single clinical or mechanical study directly comparing a cemented and a cementless version of the same stem. We investigated the load-to-failure force of a cementless and a cemented version of a double tapered stem. Material and methods - 10 femurs from 5 human cadaveric specimens, mean age 74 years (68-79) were extracted. Bone mineral density (BMD) was measured using peripheral quantitative computed tomography. None of the specimens had a compromised quality (average T value 0.0, -1.0 to 1.4). Each specimen from a pair randomly received a cemented or a cementless version of the same stem. A material testing machine was used for lateral load-to-failure test of up to a maximal load of 5.0 kN. Results - Average load-to-failure of the cemented stem was 2.8 kN (2.3-3.2) and 2.2 kN (1.8-2.8) for the cementless stem (p = 0.002). The cemented version of the stem sustained a higher load than its cementless counterpart in all cases. Failure force was not statistically significantly correlated to BMD (p = 0.07). Interpretation - Implanting a cemented version of the stem increases the load-to-failure force by 25%.