Anterior transarticular C1-C2 fixation with contralateral screw insertion: a report of two cases and technical note

Anterior Transarticular Crossing Screw Fixation for Atlantoaxial Joint Instability: A Biomechanical Study

OBJECTIVE

To evaluate the biomechanical stability of anterior transarticular crossing screw (ATCS) and compare it with anterior transarticular screw (ATS) which may provide basic evidence for clinical application.

METHODS

Eight human fresh cadaveric specimens (occiput-C4) were tested with 5 conditions including the intact status, the injury status (type II odontoid fracture), the injury+ATS fixation status (traditional bilateral ATS fixation); the injury+unilateral ATCS fixation status; and the injury+bilateral ATCS fixation status. Specimens were applied to a pure moment of 1.5 Nm in flexion-extension, lateral bending, and axial rotation, respectively. The range of motions (ROMs) and the neutral zones (NZs) of C1 to C2 segment were calculated and compared between 5 status.

RESULTS

ATS and ATCS fixations significantly reduced the motions in all directions when compared with the intact and injury statues (p < 0.05). In flexion-extension, the ROMs of ATS, unilateral ATCS, and bilateral ATCS were 4.7° ± 2.5°, 4.1° ± 1.9°, and 3.2° ± 1.2°, respectively. Bilateral ATCS resulted in a significant decrease in ROM in flexion-extension when compared with ATS and unilateral ATCS (p = 0.035 and p = 0.023). In lateral bending and axial rotation, there was no significant difference in ROM between the 3 fixations (p > 0.05). Three fixations resulted in similar NZs in all directions (p > 0.05).

CONCLUSION

ATCS is a biomechanically effective alternative or supplemental method for atlantoaxial instability.

Anterior Transarticular Crossing Screw Placement for Atlantoaxial Instability in Children: Computed Tomography-Based Study

OBJECTIVE

The feasibility of anterior transarticular crossing screw (ATCS) fixation for atlantoaxial instability was confirmed in adults. However, atlantoaxial instability is more common in children. Therefore this study was aimed to ascertain the pediatric morphometric characteristics of ATCS in C1-2.

METHODS

Morphometric analysis was conducted on computed tomography scan in 87 pediatric patients who were divided into groups based on ages (1-6 years, 7-10 years, and 11-16 years). Measurements were taken in sagittal and axial planes of computed tomography imaging to determine the range of screw lateral angles, incline angles, and screw lengths.

RESULTS

The overall screw lengths were relatively longer in males than females. For those aged 1-6 years, the screw lengths were 25.5-32.8 mm in males and 24.2-31.3 mm in females, respectively. The screw lengths showed no difference in the 7- to 10-year group between sexes, while the incline angle was larger in females than males. And the screw lengths were 33.5-43.2 mm in males and 31.2-40.4 mm in females in the 11- to 16-year group. The screw lengths were increased with age, yet the lateral angles were decreased. We also found that the epiphyseal closure of odontoid reached 93.6% when the age was older than 7 years old. Therefore ATCS was recommended for children older than 7 years.

CONCLUSIONS

The overall screw lengths and lateral angles of ATCS were larger in male children than those in females, but the incline angles were larger in females. ATCS is feasible in children, particularly those aged 7 years or older.

Radiologic Characteristics of Anterior Transarticular Crossing Screw Placement for Atlantoaxial Joint Instability

OBJECTIVE

The feasibility of anterior transarticular crossing screws (ATCS) was confirmed in cadaveric specimens and it has been used in clinic. However, no study has documented the morphometric characteristics of ATCS. This study seeks to determine the morphometric characteristics of ATCS in C1-C2 fixation.

METHODS

A total of 100 patients without abnormality of C1-2 were enrolled. The range of screw lateral angles (LAs) and the screw lengths of ATCS on coronal images were measured on multiplanar computed tomography images, as well as the screw incline angles (IAs) in the sagittal plane. The ideal trajectory was designed as toward to the posterosuperior points of the opposite C1 lateral mass, which had the longest screw.

RESULTS

The LAs were relatively small in men (31.4°-45.3°) compared with women (32.6°-46.0°). In the sagittal plane, the IAs were ranged from 41.0° to 68.4° in men and from 44.4° to 68.1° in women. The overall screw lengths were longer in men (34.7-44.8 mm) than in women (32.2-39.6 mm). In the ideal path, the LA and IA were 38.4° and 41.0° in men and 39.6° and 44.4° in women, and the screw lengths were 44.8 mm in men and 39.6 mm in women.

CONCLUSIONS

This study provides the range of screw angles and lengths of ATCS, which will help surgeons to perform ATCS safely and accurately.