Posterior unilateral exposure and stability reconstruction with pedicle and lamina screw fixation for the cervical dumbbell tumorectomy: a case report and biomechanical study

Ipsilateral Fixation and Reconstruction of the Cervical Spine after Resection of a Dumbbell Tumor Via a Unilateral Posterior Approach: A Case Report and Biomechanical Study

OBJECTIVE

There is lack of an internal fixation following resection of a dumbbell tumor by hemi-laminectomy and facetectomy that achieves adequate stability with less trauma. Unilateral fixation and reconstruction (unilateral pedicle screw and contralateral lamina screw fixation combined with lateral mass reconstruction, UPS + CLS + LM) may be an ideal technique to address this problem. A biomechanical comparison and a case report were designed to evaluate its spinal stability and clinical effect.

METHODS

Seven fresh-frozen human subcervical specimens were used for the biomechanical testing. The conditions tested were: (1) intact; (2) injured (single-level hemi-laminectomy and facetectomy); (3) unilateral pedicle screw (UPS) fixation; (4) UPS fixation combined with lateral mass (LM) reconstruction (UPS + LM); (5) UPS fixation and contralateral lamina screw fixation (UPS + CLS); (6) UPS + CLS + LM; (7) UPS fixation and contralateral transarticular screw fixation (UPS + CTAS); (8) bilateral pedicle screw (BPS) fixation. Range of motion (ROM) and neutral zone (NZ) were obtained at C5-C7 segment under eight conditions. In addition, we report the case of a patient with a C7-T1 dumbbell tumor that was treated by UPS + CLS + LM technique.

RESULTS

Except left/right lateral bending and right axial rotation (all, p < 0.05), ROM of UPS + CLS + LM condition in other directions was similar to that of BPS condition (all, p > 0.05). There was no significant difference between UPS + CLS + LM and the UPS + CTAS condition in other directions of ROM (all, p > 0.05), except in left/right axial rotation (both, p < 0.05). Compared to UPS + CLS condition, left/right lateral bending ROM of UPS + CLS + LM condition were significantly reduced (both, p < 0.05). UPS + CLS + LM condition significantly reduced ROM in all directions compared to UPS and UPS + LM condition (all, p < 0.05). Similarly, except lateral bending (p < 0.05), there was no difference in NZ in other directions between UPS + CLS + LM and BPS condition (both, p > 0.05). There was no significant difference between UPS + CLS + LM and UPS + CTAS condition in NZ in all directions (all, p > 0.05). Axial rotation NZ of UPS + CLS + LM condition was significantly reduced compared to UPS + CLS condition (p < 0.05). Compared to UPS and UPS + LM condition, NZ of UPS + CLS + LM condition was significantly reduced in all directions (all, p < 0.05). The patient's imaging examination at 3 months postoperatively indicated that the internal fixation did not move and the graft bone was seen with fusion.

CONCLUSION

After resection of a dumbbell tumor in the cervical spine, UPS + CLS + LM technique is a reliable internal fixation method to provide sufficient immediate stability and promote postoperative bone fusion.

Biomechanical evaluation of subaxial lateral mass prothesis: a finite element analysis study

Pathologies of the lateral masses could lead to bone destruction of the cervical spine. Their treatment includes lesion resection and fixation. However, the resulting bone defect of a lateral mass is often neglected, resulting in difficulty in bone fusion. Therefore, we designed a subaxial lateral mass prosthesis to achieve lateral mass joint fusion. This study aims to evaluate the role of a new subaxial lateral mass prosthesis using finite element analysis. Five finite element models (intact, lateral mass resection, screw-rod fixation, prosthesis implantation, and prosthesis fusion groups) were compared in terms of the range of motion (ROM), prosthesis von Mises stress, and screw-rod von Mises stress during flexion, extension, lateral bending, and rotation. The ROM of the model increased significantly after lateral mass resection, and was significantly reduced after fixation with screws and rods. Screw-rod fixation combined with prosthesis implantation further reduced the ROM. After bone fusion in the prosthesis, the ROM can also be reduced slightly. The von Mises stress of the bilateral screws and rods significantly decreased after prosthesis implantation. The von Mises stress of the prosthesis further decreased during the right bending after bone fusion was achieved. Subaxial lateral mass prosthesis can help restore the stability of the cervical spine after lateral mass resection and can reduce the stress on the bilateral screws and rods. Reconstruction of a lateral mass is more consistent with the mechanical transmission of the three-column spine and contributes to interfacet fusion of the lateral mass joint.

Reconstruction of the cervical lateral mass using 3D-printed prostheses

Objective

This study aimed to investigate the outcome of using 3-dimensional (3D)-printed prostheses to reconstruct a cervical lateral mass to maintain cervical stability.

Methods

We retrospectively analyzed data of 7 patients who underwent cervical lateral mass reconstruction using a 3D-printed prosthesis, comprising axial and subaxial lateral mass reconstruction in 2 and 5 patients, respectively. Bilateral mass was reconstructed in 1 patient and unilateral mass in the remaining 6 patients.

Results

Using a 3D-printed lateral mass prosthesis, internal fixation was stable for all 7 patients postoperatively. No implant-related complications such as prosthesis loosening, displacement, and compression were observed at the last follow-up.

Conclusion

Reconstruction of the lateral mass structure is beneficial in restoring load transfer in the cervical spine under physiological conditions. A 3D-printed prosthesis can be considered a good option for reconstruction of the lateral mass as fusion was achieved, with no subsequent complications observed.

Subaxial lateral mass prosthesis for posterior reconstruction of cervical spine

PURPOSE

To obtain the relevant morphometry of the lateral mass of the subaxial cervical spine (C3-C7) and to design a series of lateral mass prostheses for the posterior reconstruction of the stability of cervical spine.

METHODS

The computed tomography (CT) scans of healthy volunteers were obtained. RadiAnt DICOM Viewer software (Version 2020.1, Medixant, Poland) was used to measure the parameters of lateral mass, such as height, anteroposterior dimension (APD), mediolateral dimension (MLD) and facet joint angle. According to the parameters, a series of cervical lateral mass prostheses were designed. Cadaver experiment was conducted to demonstrate its feasibility.

RESULTS

23 volunteers with an average age of 30.1 ± 7.1 years were enrolled in this study. The height of lateral mass is 14.1 mm averagely. Facet joint angle, APD and MLD of lateral mass averaged 40.1 degrees, 11.2 mm and 12.18 mm, respectively. With these key data, a lateral mass prosthesis consists of a bone grafting column and a posterior fixation plate was designed. The column has a 4.0 mm radius, 41 degrees surface angle and adjustable height of 13, 15, or 17 mm. In the cadaver experiment, the grafting column could function as a supporting structure between adjacent facets, and it would not violate exiting nerve root (NR) or vertebral artery (VA).

CONCLUSION

This study provided detailed morphology of the lateral mass of subaxial cervical spine. A series of subaxial cervical lateral mass prostheses were designed awaiting further clinical application.