The correlation between clinical radiological outcome and contact state of implant and femur using three-dimensional templating software in cementless total hip arthroplasty

Subsidence of the Corail stem in total hip arthroplasty: no influence of bony contact

INTRODUCTION

This study investigated stem subsidence following primary total hip arthroplasty (THA) with a Corail stem in patients who underwent two-staged bilateral THA. The second outcome of interest was to investigate whether a specific single cortical bone contact point might reduce postoperative stem subsidence.

METHODS

The present study was conducted following the STROBE guidelines. The records of patients who underwent THA between 2016 and 2023 were accessed. All patients who underwent two-staged bilateral THA were retrieved. The direct contact between the stem and the cortical bone was assessed at various points in the metaphysis and the distal portion of the stem (diaphysis) in both anteroposterior radiographs of the pelvis (medial and lateral bone contact) and a Lauenstein view of the hip (anterior and posterior bone contact). The following parameters were measured and compared to assess stem subsidence: distance from the proximal femur at the stem bone interface and the tip of the lesser trochanter (distance A); distance from the tip of the lesser trochanter and the tip of the femoral stem (distance B).

RESULTS

In total, 250 patients were included, 45% (149 of 250 patients) were women and 61% (153 of 250 THAs) were implanted primarily on the right side. The mean age of patients at the time of the first THA was 64.3 ± 10.0 years and the mean body mass index (BMI) was 28.0 ± 4.9 kg/m2. The mean length of the follow-up was 14.1 ± 10.8 months. The overall stem subsidence following THA was 2.8 ± 0.7 mm (P < 0.006). A direct cortical bone-implant contact did not exert a statistically significant difference in subsidence of the THA stem at the metaphysis and diaphysis (P > 0.5). Stem subsidence following THA with a collarless cementless Corail stem was approximately 2.8 mm at 14 months.

CONCLUSIONS

Direct cortical bone contact of the stem at diaphysis and metaphysis seems not to influence stem subsidence following THA using the Corail stem.

Influence of Femoral Stem Geometry on Total Hip Replacement: A Comparison of Clinical Outcomes of a Straight and an Anatomical Uncemented Stem

Background/Objectives: There are many aspects that may influence clinical outcomes in a total hip arthroplasty (THA). The influence of femoral stem on the clinical outcome of THA is probably underestimated in the literature. Our work aims to analyze how uncemented stem geometry (straight or anatomical) in THA might affect outcomes in clinical and radiographic terms. Methods: Over a period of 36 months, in a prospective-observational manner, we collected the results of THA secondary to osteoarthritis (OA) that met the inclusion criteria with the only variable being the straight or anatomical stem design in a single manufacturer. A total of 84 patients were selected and divided into two groups: group A, treated with straight stem (44 patients), and group B, treated with anatomical stem (40 patients). The assessment clinical tools were Harris Hip Score (HHS), Visual Analogue Scale (VAS), and Short Form Health Survey-36 (SF-36). Follow-up controls were at 6 months (T0), 12 months (T1), 24 months (T2), and 36 months (T3). Results: No statistically significant differences emerged between the two groups under analysis with VAS, SF-36, and HHS. At follow-up controls, eight patients (group A) and four patients (group B) showed anterior thigh pain. At T1, there were radiographic signs of aseptic loosening in two cases (group A) and one case (group B). In group A there were two cases of iatrogenic fracture, two cases of dislocation, one case of infection, and two cases of heterotopic ossification. Conclusions: The anatomical stem compared to the straight stem showed lower complication rates outcomes; the anatomical uncemented stem could be considered as a preferred first choice in THA compared to the straight stem.

Stress shielding following radial head arthroplasty: the impact of preoperative bone quality

BACKGROUND

We sought to assess if the medullary diameter to cortical width ratio (MD:CW), canal flair index (CFI), and canal fill (CF) of the proximal radius were associated with the presence of stress shielding (SS) after a MoPyC radial head arthroplasty.

MATERIALS AND METHODS

We conducted a retrospective, international, multicenter (4 centers) study. A total of 100 radial head arthroplasties in 64 women and 36 men with a mean age of 58.40 years ± 14.90 (range, 25.00-91.00) were included. Radiographic measurements, including MD:CW, CFI, CF, and postoperative SS were captured at a mean follow-up of 3.9 years ± 2.8 (range, 0.5-11).

RESULTS

SS was identified in 60 patients. Mean preoperative MD:CW, CFI, and CF were 0.55 ± 0.09, 1.05 ± 0.18, and 0.79 ± 0.11, respectively. The presence of SS was significantly associated with MD:CW (adjusted odds ratio = 13.66; P = .001), and expansion of the stem (adjusted odds ratio = 3.78; P = .001). The amount of the SS was significantly correlated with expansion of the stem (aβ 4.58; P < .001).

CONCLUSIONS

Our study found that MD:CW was an independent risk factor of SS after MoPyc radial head arthroplasty. Autoexpansion of the MoPyc stem significantly increased the risk of SS and its extent. Further studies involving multiple implants designs are needed to confirm the preliminary observations presented in the current study.

Comparison of femoral bone remodeling after total hip arthroplasty with cementless short-tapered wedge stem and fully hydroxyapatite-coated stem

INTRODUCTION

We aimed to compare periprosthetic femoral bone remodeling after cementless total hip arthroplasty (THA) using a short-tapered wedge stem and a fully hydroxyapatite (HA)-coated stem.

MATERIALS AND METHODS

In this retrospective study, 24 primary cementless THA procedures with short-tapered wedge stem and 24 using a fully HA-coated stem were performed. The follow-up duration was 2 years for both groups. Clinical evaluation was performed using the Merle d'Aubigné and Postel scoring systems. Standardized anteroposterior radiographs of the pelvis and femur were obtained. Dual-energy X-ray absorptiometry was performed, and the bone mineral density (BMD) around the stem was assessed in each Gruen zone at the first postoperative week as a baseline value and at 6 weeks, 3 and 6 months, and 1 and 2 years postoperatively.

RESULTS

The mean Merle d'Aubigné and Postel scores improved significantly postoperatively in both groups. None of the hips showed loosening in either group. Spot welds occurred in zones 1, 2, 6, and 7 in the short-tapered wedge group, and in all zones in the fully HA-coated group. Significant BMD loss occurred only in zone 4 in the short-tapered wedge group, and no significant bone loss occurred in any zone in the fully HA-coated stem group; a significant difference between the two groups was observed only in zone 4 at 2 years after THA.

CONCLUSIONS

Clinical and radiographical outcomes in both groups were good, and both stems suppressed postoperative BMD loss at 2 years.

Is bone remodelling around fully hydroxyapatite-coated and tapered-wedge stems related to the stem fixation pattern?

PURPOSE

This study aimed to compare bone mineral density (BMD) changes around the femoral component after total hip arthroplasty (THA) in a fully hydroxyapatite-coated stem (CORAIL) and in a tapered-wedge stem (Taperloc complete) and identify predictors of BMD changes.

METHODS

This retrospective study compared 43 hips in the CORAIL group and 40 hips in the Taperloc group. The relative changes in BMD at 2 years after THA measured using dual-energy X-ray absorptiometry and the three-dimensional quantified contact states of the stem with the femoral cortical bone were assessed. Predictors of the relative change in the BMD around the proximal part of the stem were examined using multiple regression analysis.

RESULTS

The decrease in BMD in Gruen zone 7 was significantly less in the CORAIL group than in the Taperloc group (P = 0.02). In the CORAIL group, the contact area in any zone was not a significant predictor of the relative changes in BMD. The contact area between the Taperloc stem and the femoral cortical bone in zones 2 and 6 was a positive predictor of the relative changes in BMD in zones 1 (P = 0.02 and P = 0.04, respectively) and 2 (P = 0.008 and P = 0.004, respectively).

CONCLUSION

The CORAIL stem suppressed the postoperative BMD loss around the stem, irrespective of the contact state. The Taperloc complete stem required contact with the proximal femoral metaphysis to suppress the postoperative BMD loss around the stem.

Comparative Study for Postoperative Initial Fixation Patterns of Two Different Types of Cementless Short Stem Using Three-Dimensional Templating Software

Background

While cementless short stems have become popular in total hip arthroplasty (THA), Metha is a relatively recent development that differs from other short stems in its initial fixation concept of partial collum-sparing metaphyseal anchorage. The purpose of this study was to quantify the contact state between Metha and the femur. Additionally, we investigated the difference in contact points between Meta and Fitmore, which is one of the more popular curved short stems.

Methods

We conducted a retrospective review of 42 hips that underwent THA using Metha and 41 hips using Fitmore. Stem-to-femur contact was evaluated by density mapping using a three-dimensional digital template system to quantify the contact condition according to the modified Gruen zone. The criterion for the stem-to-bone contact boundary was defined as a computed tomography value of 543 Hounsfield.

Results

Quantitative evaluation of Metha according to the modified Gruen zones showed the ratio of surface area with high cortical contact in each zone. The results were 4.6% ± 5.7% in zone 1, 0.9% ± 2.3% in zone 2, 19.1% ± 12.9% in zone 3, 1.4% ± 3.2% in zone 5, 29.6% ± 16.4% in zone 6, and 25.1% ± 17.7% in zones 7. Evaluation of Fitmore for the same zones was as follows: 1.6% ± 2.4%, 18.5% ± 16.9%, 20.8% ± 17.4%, 12.7% ± 12.8%, 3.7% ± 5.8%, and 13.3% ± 10.3%. Comparing the two groups, the contact area was significantly greater for Metha in zones 1, 6 and 7 and Fitmore in zones 2 and 5 (p < 0.05).

Conclusions

It is possible for Metha to achieve metaphyseal anchoring by contacting the cortical bone at the proximal femur, thus avoiding proximal offloading. To the best of our knowledge, no previous studies have quantitatively reported stem-to-cortical bone contact conditions in curved short stems.

Overall Accuracy of Radiological Digital Planning for Total Hip Arthroplasty in a Specialized Orthopaedics Hospital

Preoperative radiological planning is a key factor in the prediction of implant size and positioning that influences surgical time, the risk of complications, and functional outcomes. We have tested the accuracy of the digital templating performed in our hospital for a sample of 215 patients that underwent total hip arthroplasty. We assessed the accuracy of correctly predicting implant size for the femoral and acetabular components, as well as the stem neck length. We found that our method of templating proved accurate (within one size) in 95.8% of cases for the stem and 94.9% for the cup when using the anteroposterior view only, while the lateral view was accurate in 95.8% of cases for the stem and 97.2% for the cup. Exact prediction of the stem size was obtained in 77.7% of cases using the anteroposterior view and 67.0% of cases on the lateral view, and 73.0% and 74.4% of cases for the cup on the AP and LL views, respectively. Stem neck size was predicted exactly in 75.35% of cases and within one size in 93.49% of cases. We concluded that our method of digital templating using dedicated software is highly effective in accurately predicting implant size.

Relationship between Stress Shielding and Optimal Femoral Canal Contact Regions for Short, Tapered-Wedge Stem Analyzed by 2D and 3D Systems in Total Hip Arthroplasty

Although tapered-wedge short stem has been widely employed with its availability for minimally invasive surgeries in total hip arthroplasty (THA), post-operative stress shielding matter remains unresolved in cementless procedures. This study aimed to clarify the most optimal femoral canal contact regions of the stem design taking stress shielding incidence into consideration. This investigation included 60 joints from 60 patients (mean age at operation: 65.9 years), of which follow-up duration after primary THA had been more than 2 years. Frequencies of spot welds, subsidence, and stress shielding were examined 2 years after surgery. The most suitable femoral canal contact regions were evaluated by plain radiograph (2D) and 3D-computed tomography analyses according to Nakata's division for fitting manners. Spot welds were observed in 38 cases (63.3%), and no subsidence case was seen. Respective number of stress shielding cases, based on Engh's classification, categorized as degree 0, 1, and 2, were 2 (3.3%), 31 (51.7%), and 27 (45.0%), while no cases for degree 3 or 4 were found. When assessed by 3D fitting analysis, 27 cases of stress shielding degree 2 were constituted by 13/42 cases of mediolateral (ML) fit, 2/4 cases of flare fit, and 12/14 cases of multi point fit. In 42 cases of ML fitting, stem contact rate of the most proximedial region in stress shielding degree 0 and 1 was significantly higher compared to stress shielding degree 2 cases. Meanwhile, the rates of distal regions were significantly lower or absent in stress shielding degree 0 and 1 cases. The initial fixation of this stem design was very good in our cohort regardless of fitting manners. This study successfully revealed that ML fitting with femoral component, especially the most proximedial calcar site restricted fitting, would be optimal for reducing stress shielding occurrence in cementless short, tapered-wedge stem THA. Thus, the ideal stem contact region should be considered during THA procedures in light of the reduction of stress shielding development.

The anatomical shape of the proximal femur correlates with the distal femur anatomy

PURPOSE

In the case of stemmed implants for lower limb joint arthroplasty procedures, implant stability and survivorship generally rely on the strength of fixation in the medullary canal regardless of whether the procedure is primary or revision surgery. This study aimed to investigate the relationship between the proximal (Dorr classification) and distal (Citak classification) femoral canal geometry classification systems.

METHODS

A total of 200 patients who received standing long leg radiographs (hip to ankle) at our institution were identified using our institutional electronic radiology database. Patients were recruited into 4 groups. There were 100 male and 100 female patients with each of those being split into 50 right-sided and 50 left-sided long-leg standing anteroposterior (AP) radiographs. Two independent, blinded observers reviewed each radiograph on two separate occasions, with a minimum of a one-week interval between sittings to review each respective radiograph.

RESULTS

No statistically significant correlation was found between demographic data and clinical measurements. A statistically significant correlation was found between the patient's age and BMI results and Citak and Dorr measurements. There was excellent inter-observer and intra-observer agreement for the Citak and Dorr Classifications. The mean Cronbach's α coefficient was 0.96 (range 0.93-0.98) for the Citak Classification and 0.95 (range 0.83-0.97) for the Dorr Classification. There was also an excellent intra-observer agreement with 95% average pairwise per cent agreement for the Citak Classification and 95% average pairwise per cent agreement for the Dorr classification. A statistically significant positive correlation was found between Dorr Calcar Isthmus and Citak Ratio (p < 0.05).

CONCLUSION

In this study, the Dorr and Citak classifications are put into relation to each other for the first time. The morphology of the femur was investigated in its entirety and it was shown that there was a positive correlation between the anatomical shape of the proximal and distal medullary canals.

Clinical and radiographic outcomes of primary total hip arthroplasty with the revelation hip system using density mapping

The Revelation Hip System is a cementless stem with a lateral flare concept. Stable fixation is achieved by fitting the stem to the medullary cavity of the proximal lateral femoral cortex. Patients who have undergone total hip arthroplasty using the Revelation Hip System show good postoperative clinical and radiographic outcomes. However, to the best of our knowledge, no study has reported the relationship between stem fitting and clinical or radiological outcomes after the surgery. In the present study, we investigated the relationship between stem fitting and clinical or radiological outcomes after total hip arthroplasty (THA) using the Revelation Hip System. In this study, 28 hips of 26 patients who were treated with the Revelation Hip System for osteoarthritis, osteonecrosis of the femoral head, rheumatoid arthritis, and rapidly destructive coxarthropathy and were followed up for > 5 y were enrolled. These patients were divided into two groups, including the rest fit group (11 hips, group R) and the control group (17 hips, group C), according to the results of the density mapping analysis. In group R, the lateral side of the stem fits on the medullary cavity of the proximal lateral femoral cortex, while in group C, the lateral side of the stem did not fit. Radiographic results showed no significant differences between the groups in terms of stem alignment, subsidence, and stress shielding around the cup. The incidence of stress shielding around the stem in zone 7 was not significant but tended to be higher in group R than in group C (p = 0.052). Clinical outcomes showed no significant differences between group R and group C in terms of the Harris hip score, the Japanese Orthopaedic Association (JOA) score, and the Japanese Orthopaedic Association Hip Disease Evaluation Questionnaire (JHEQ) total score. However, pain complaints that were assessed by patient-reported outcomes using the 36-Item Short Form Health Survey (SF-36) bodily pain and vitality subscales and the JHEQ pain subscale were significantly higher in group R than in group C at the final follow-up. These results suggest that some patients had pain complaint even if the stems were inserted as per the concept after THA with the Revelation Hip System.Trial Registration911.

Differences in peri-hip articular pain after total hip arthroplasty between taper wedge stem and fit-and-fill stem

Background

Total hip arthroplasty (THA) for hip disorders helps to alleviate pain and improve active daily life. When determining the effects of medical therapy and the subsequent clinical results, patient quality of life (QOL) also needs to be assessed. Recently, patient-reported outcomes (PRO) have become important as evaluation criteria. This study aimed to evaluate patient QOL and various PRO between different types of cementless stems and to clarify the relationship between PRO and stem-cortical bone contact.

Methods

The study comprised 138 consecutive patients undergoing cementless THA for hip osteoarthritis. We assessed three different types of PRO: the Japanese Orthopaedic Association Hip-Disease Evaluation Questionnaire (JHEQ), patient's joint perception, and peri-hip articular joint pain (PHAP). We measured the state of contact between femur and implant by density mapping.

Results

No significant difference was noted in PRO between stem types based on the JHEQ and patient's joint perception. PHAP occurred more frequently in the patients with a taper wedge stem versus a fit-and-fill stem. In both groups, distal contact was associated with PHAP but not with JHEQ results and patient's joint perception.

Conclusion

The difference in PHAP between the two stem types groups was significant, with postoperative PHAP being higher with the taper wedge stem because of the more distal contact between the taper wedge stem and femur cortical bone.

A double tapered fully hydroxyapatite-coated stem has less contact area to femoral cortical bone than a tapered-wedge stem: a three-dimensional computed tomography-based density mapping analysis

INTRODUCTION

It is clinically important to analyze the initial contact state between an implant and femoral cortical bone as it affects clinical outcomes, such as stress shielding, stem subsidence, thigh pain, and patient-reported outcomes after total hip arthroplasty. Whether the initial contact state of a double-tapered fully hydroxyapatite (HA)-coated stem is achieved with the preserved cancellous or cortical bone remains to be established. This study aimed to compare the contact area with the femoral cortical bone between a double-tapered fully HA-coated stem (HA group) and a tapered wedge cementless stem (TW group) using three-dimensional computed tomography (3DCT)-based templating software.

MATERIALS AND METHODS

Forty-seven total hip arthroplasties in the HA and TW groups each were retrospectively analyzed. The contact area between the implant and femoral cortical bone in the whole stem and at each Gruen zone was measured using density mapping with 3DCT-based templating software.

RESULTS

The demographic data were not significantly different between the two groups. The contact area in the whole stem area was lower in the HA group (HA 5.4 ± 1.8% vs. TW 9.0 ± 4.8%, p < 0.01). The HA group had a lower contact area in zone 2 (HA 6.7 ± 6.5% vs. TW 15.6 ± 10.8%, p < 0.01) and zone 6 (HA 1.8 ± 3.5% vs. TW 6.3 ± 3.6%, p < 0.01) than the TW group. The implant type (β = 0.41, p < 0.01) and stem coronal alignment (β = - 0.29, p < 0.01) were significant predictors of the contact area in the whole stem area in a multiple regression analysis (adjusted R² = 0.27, p < 0.01).

CONCLUSION

The contact area of the double-tapered fully HA-coated stem was significantly lower than that of the tapered wedge cementless stem.

Effect of trochanter displacement on impingement and bone contact in total hip arthroplasty performed after curved intertrochanteric varus osteotomy for osteonecrosis of the femoral head: a simulation study

Background

Curved intertrochanteric varus osteotomy (CVO) is a useful treatment option for osteonecrosis of the femoral head (ONFH). However, the effect of proximal femoral deformity in cases of CVO converted to total hip arthroplasty (THA) remains unclear. The aim of this study was to evaluate the effect of trochanter displacement on impingement and the contact state of the implant and femur in THA.

Methods

Thirty-eight hips that had undergone CVO for ONFH were reviewed and compared with a control group of 30 contralateral hips that had not undergone surgery. The range of motion (ROM) and impingement patterns and the percentage of cortical bone in the stem placement within the femur were measured by simulation using CT-based three-dimensional template software. We also measured the ROM and the number of joints that achieved the ROM required for activities of daily living when the upward displaced apex of the greater trochanter with osteotomy was resected and compared the findings with those obtained when the apex was not resected.

Results

The CVO group showed a significantly greater bony impingement in external rotation (68.4% vs. 43.3%, p = 0.033) and abduction (78.9% vs. 33.3%, p < 0.001) than in the control group. The CVO group showed a significantly smaller range of external rotation (19.0° [interquartile range; 4.0–28.8] vs. 38.0° [interquartile range; 36.0–41.8], p < 0.001) and abduction (23.0° [interquartile range; 8.5–38.8] vs. 56.0° [interquartile range; 50.3–60.0], p < 0.001) than in the control group. Significantly more joints achieved the ROM necessary for activities of daily living when the apex was resected than when it was not (10.5% vs. 63.2%, p < 0.001). The percentage of cortical bone in the stem placement position was significantly higher in the CVO group than in the control group in the proximal portion of the stem (25.5% vs. 0.0%, p < 0.001).

Conclusion

In cases requiring conversion to THA, we recommend resecting the upward displaced apex to achieve a sufficient ROM and carefully resecting the bone to avoid malignment of the stem.

Distal femoral cortical hypertrophy not associated with thigh pain using a short stem femoral implant

BACKGROUND

Thigh pain following a well-fixed total hip arthroplasty (THA) remains problematic and a source of patient dissatisfaction. The purpose of this study is to evaluate if the development of distal femoral cortical hypertrophy (DFCH) is associated with postoperative thigh pain after THA.

METHODS

All patients who underwent an uncomplicated primary THA via a direct anterior approach with the Taperloc Microplasty (Zimmer Biomet, Warsaw, IN, USA) implant between 2011 and 2015 were mailed a pain drawing questionnaire. Radiographs were reviewed at 1 year minimum to determine cortical thickness change from immediate post-op. Thigh pain was compared to DFCH. 293 patients were included in the study.

RESULTS

Mean follow-up was 3.2 years. A total of 218 hips (74%) had cortical hypertrophy in Gruen zone 3 and 165 hips (56%) had cortical hypertrophy in Gruen zone 5. 52 hips (18%) had ⩾25% cortical hypertrophy in zone 3 and 91 hips (31%) had ⩾25% cortical hypertrophy in zone 5. A total of 44 patients (15%) reported anterior thigh pain and 43 patients (15%) reported lateral thigh pain. Development of DFCH in either Gruen zone 3 or 5 was not associated with anterior or lateral thigh pain. Stem size was positively correlated with zone 3 hypertrophy and inversely related to zone 5 hypertrophy. Thigh pain was not associated with patient age, gender, activity level or stem size.

CONCLUSIONS

The development of distal femoral cortical hypertrophy after THA with a short stem implant was high, but not associated with patient-reported anterior or lateral thigh pain.

The use of density mapping in the analysis of thigh pain after total hip arthroplasty in patients with well-fixed tapered wedge stems

PURPOSE

The mechanisms underlying thigh pain in patients with well-fixed cementless femoral components after total hip arthroplasty (THA) remains unclear. We hypothesized that the thigh pain is correlated with the initial contact state of the stem and aimed to investigate the relation between thigh pain and the initial contact state.

MATERIALS AND METHODS

A total of 209 hips of 184 patients were analysed in this retrospective case-control study. The patients were divided into a thigh pain group (n = 13 hips) and a control group (without thigh pain, n = 196). Post-operative stem contact images were three-dimensionally visualized by a density mapping function using computed tomography data, which quantified the stem contact area according to Gruen zones. Thigh pain was defined as anterior or anterolateral pain upon loading at 3-month post-operatively.

RESULTS

Thirteen hips (6.2%) had thigh pain; however, all the hips demonstrated stable bony ingrowth radiographically. The thigh pain group had a significantly lower contact area in zone 2 (p = 0.014). The multivariate logistic regression analysis showed that the contact area of zone 2 was negatively correlated with thigh pain [odds ratio (OR): 0.858, p = 0.018], and the canal flare index was negatively correlated with the development of thigh pain (OR: 0.336, p = 0.026).

CONCLUSIONS

We identified an association between the initial contact state and post-operative thigh pain. Our data demonstrated that proper lateral contact prevents the occurrence of thigh pain in THA using a tapered wedge stem.

Three-dimensional pre-operative planning of primary hip arthroplasty: a systematic literature review

Three-dimensional (3D) pre-operative planning in total hip arthroplasty (THA) is being recognized as a useful tool in planning elective surgery, and as crucial to define the optimal component size, position and orientation. The aim of this study was to systematically review the existing literature for the use of 3D pre-operative planning in primary THA.A systematic literature search was performed using keywords, through PubMed, Scopus and Google Scholar, to retrieve all publications documenting the use of 3D planning in primary THA. We focussed on (1) the accuracy of implant sizing, restoration of hip biomechanics and component orientation; (2) the benefits and barriers of this tool; and (3) current gaps in literature and clinical practice.Clinical studies have highlighted the accuracy of 3D pre-operative planning in predicting the optimal component size and orientation in primary THAs. Component size planning accuracy ranged between 34-100% and 41-100% for the stem and cup respectively. The absolute, average difference between planned and achieved values of leg length, offset, centre of rotation, stem version, cup version, inclination and abduction were 1 mm, 1 mm, 2 mm, 4°, 7°, 0.5° and 4° respectively.Benefits include 3D representation of the human anatomy for precise sizing and surgical execution. Barriers include increased radiation dose, learning curve and cost. Long-term evidence investigating this technology is limited.Emphasis should be placed on understanding the health economics of an optimized implant inventory as well as long-term clinical outcomes. Cite this article: EFORT Open Rev 2020;5:845-855. DOI: 10.1302/2058-5241.5.200046.

Influence of pelvic sagittal tilt on 3-dimensional bone coverage in total hip arthroplasty: a simulation analysis

BACKGROUND

In total hip arthroplasty with computer navigation assistance, cup orientation is generally determined according to the coordinate system relative to the functional pelvic plane (FPP). However, there is a large difference in the cup anteversion between a posterior pelvic tilt relative to the computed tomography (CT) table in the sagittal plane and anterior pelvic tilt, even when the cup is set at the same orientation angle according to each FPP. The present study analysed this difference from the viewpoint of 3-dimensional (3D) coverage of the acetabular component (3D coverage) to determine how the 3D acetabular coverage is altered with changes in pelvic sagittal tilt.

METHODS

We analysed 3D-simulated acetabular coverage measured in 3D pelvic models reconstructed from the preoperative CT data of 50 patients. In each patient, we created 5 pelvic models with a sagittal tilt of 10° increments between 20° anterior tilt and 20° posterior tilt relative to the CT table.

RESULTS

We found that 3D coverage decreased as the pelvis tilted posteriorly. Particularly, there were significant differences between the pelvis with 20° anterior tilt and that with neutral tilt (p < 0.001). There was also a difference between the pelvis with neutral tilt and that with a 20° posterior tilt (p < 0.01). The mean decrease in 3D coverage between the pelvis with neutral tilt and that with 20° posterior tilt was 7.2 ± 1.6%.

CONCLUSIONS

We found that 3D coverage differed among pelvis with different sagittal tilts when the cup orientation angle was determined according to FPP.

Postoperative migration of the anatomical and functional anteversion angle following total hip arthroplasty with a well-fixed cemented femoral component with line-to-line implantation

INTRODUCTION

Little is known about the association between well-fixed polished tapered cemented stems (PTCS) implanted by the line-to-line technique and changes of stem migration, or the change of functional anteversion of the femur after total hip arthroplasty (THA).

MATERIALS AND METHODS

This retrospective study included 422 two-stage bilateral primary THAs performed using PTCS implanted by the line-to-line technique. CT scans were made on both the target side (first postoperative CT) and on the contralateral side (second postoperative CT) 1 week postoperatively. The mean follow-up was 7.8 months. CT data for each scan were transferred to 3D template software (Zed hip, Lexi, Japan). The postoperative changes of anatomical stem anteversion (ASA), functional femoral anteversion (FFA), and stem subsidence were evaluated.

RESULTS

A total of 20 THAs with CT scans were available on 3D template software. The ASA and the FFA had migrated - 0.68° ± 0.62° and - 5.5° ± 9.7°, respectively, over the follow-up period. A significant positive correlation was observed between the change of subsidence and ASA (r² = 0.34, p = 0.007), between the FFA on the second postoperative CT and ASA on the first postoperative CT (r² = 0.26, p = 0.02) and between the FFA on the second postoperative CT and FFA on the first postoperative CT (r² = 0.52, p = 0.0003).

CONCLUSION

This study indicates that the change in axial rotation of a PTCS implanted by the line-to-line technique was less than that reported by other studies and the preoperative external rotation contracture was substantially improved after THA.

Risk factors for pressure ulcers from the use of a pelvic positioner in hip surgery: a retrospective observational cohort study in 229 patients

Background

Intraoperatively acquired pressure ulcers are serious postsurgical complications requiring additional treatment, reoperation, and extended hospitalization. No study has investigated the frequency of the ulcers caused by compression with a pelvic positioner, which is used in hip surgeries to stabilize patients in the lateral decubitus position.

Methods

This retrospective study investigated the risk factors and the frequency of the ulcers caused by the use of pelvic positioners in hip surgeries. The records of patients who underwent surgical procedures under general anesthesia at our institution between January 1, 2016 and March 31, 2018 were reviewed. The inclusion criterion for the assessment of risk factors was hip surgery in the lateral decubitus position stabilized by a pelvic positioner. The exclusion criteria were patients with trauma, missing data, or a pre-existing pressure ulcer. Finally,.the study included 229 patients (265 hip surgeries). All the patients were positioned in the lateral decubitus position with the assistance of either a pelvic positioner, which had a single support fixture located over the pubic symphysis or a double support fixture located over the bilateral anterior superior iliac spine. Intraoperatively acquired pressure ulcers were diagnosed when ulcers were absent on admission and the redness that was observed immediately after surgery remained after 24 h. Multivariate analysis was used to identify factors associated with an increased risk for ulcers.

Results

Ulcers developed in 8 of 1810 (0.44%) patients who underwent orthopedic surgery. Seven of the 265 (2.64%) patients who underwent hip surgery in the lateral decubitus position stabilized by a pelvic positioner developed ulcers. All ulcers were located on areas of the body that were compressed by the pelvic positioner. After identifying controls for patient height (less than 154 cm), surgery duration (longer than 180 min), blood loss (more than 355 ml), and type of pelvic positioner used, we identified the independent risk factors for ulcers to be patient height < 154 cm (adjusted odds ratio, 12.8; p-value, 0.032) and the use of pelvic positioners with pubic bone support (adjusted odds ratio, 10.53; p-value, 0.047).

Conclusion

The use of pelvic positioners with pubic bone support should be avoided in patients with a height of < 154 cm to decrease the risk of ulcers.

Effect of transtrochanteric rotational osteotomy on impingement and contact state of a femoral implant in conversion total hip arthroplasty - Retrospective simulation study

BACKGROUND

The transtrochanteric rotational osteotomy is a common osteotomy for osteonecrosis of the femoral head, although the results of conversion total hip arthroplasty after the osteotomy are controversial. We evaluated how deformities in the proximal femur after the osteotomy affect hip impingement and the contact state of the stem in total hip arthroplasty.

METHODS

We retrospectively reviewed 35 hips (24 men) that had undergone the transtrochanteric rotational osteotomy for osteonecrosis of the femoral head (TRO-group) and compared them with 31 contralateral, unoperated hips (Primary group). The distance between the anterior and posterior greater trochanter at the cutting point of the femur, defined as the greater trochanter width and the contact area of the femoral implant surface with cortical bone were measured by CT-based three-dimensional templating software. We also calculated the hip range of motion in conversion total hip arthroplasty and analyzed the correlations between the greater trochanter width and the range of motion.

FINDINGS

The number of bony-impingement cases was significantly greater, and the range of motion in flexion, internal rotation and external rotation was significantly less in TRO-group. There was a significant negative correlation between the greater trochanter width and range of motion of internal rotation. There were no significant differences between two groups in percentages of femoral-implant contact area.

INTERPRETATIONS

The femoral implant fixation appears to be satisfactorily fixed in all zones in conversion total hip arthroplasty. However, the greater attention should be paid to minimizing bony impingement, especially on the anterior side, in conversion total hip arthroplasty.

Three-Dimensional Host Bone Coverage Required in Total Hip Arthroplasty for Developmental Dysplasia of the Hip and Its Relationship With 2-Dimensional Coverage

BACKGROUND

In total hip arthroplasty, the minimum host bone coverage required on the cup for stable fixation has been previously reported; however, the coverage was generally evaluated on a 2-dimensional (2D) image and 3-dimensional (3D) coverage has not been well described.

METHODS

We used postoperative computed tomography images to retrospectively measure 3D cup coverage in 151 hips with developmental dysplasia of the hip that underwent primary total hip arthroplasty. The aims were to (1) determine the minimum requirement of the 3D coverage for stable cup fixation; (2) evaluate the relationship between 2D and 3D coverage; and (3) identify the factors associated with 2D-3D discrepancy, defined as follows: 2D-3D discrepancy = 2D coverage-3D coverage.

RESULTS

All cups showed stable fixation as demonstrated by bone ingrowth with an average postoperative period of 48 months. The minimum 3D coverage was 61.2%, with a mean value of 77.1% ± 6.7% and maximum value of 97.6%. We found a significant positive but poor relationship between 3D and 2D coverage (bone coverage index; r = 0.30). Consequently, the 2D-3D discrepancy varied greatly, with a mean value of -1.6% ± 12.3% (range, -36.5% to 32.2%). Multiple linear regression analyses confirmed that lower cup center and anterior tilt of the pelvis relative to the computed tomography table were independent factors associated with increasing 2D-3D discrepancy.

CONCLUSION

This study showed that 2D coverage, measured on a projected image, carries a risk of overestimation, especially in hips with the aforementioned features.

The effect of flexion alignment in total hip arthroplasty with a cementless tapered-wedge femoral stem

INTRODUCTION

The influence of stem sagittal alignment on clinical outcomes is unclear in total hip arthroplasty (THA). The purpose of this study is to assess the relationship between stem sagittal alignment and clinical and radiographic outcomes using 3D-CT.

MATERIALS AND METHODS

We performed 370 consecutive primary THAs between 2009 and 2013. After exclusion, 102 hips in 89 patients using single tapered-wedge stem were included. Mean follow-up was 4.7 years. Stem sagittal alignment was measured using CT, and patients were divided into flexion and neutral alignment groups. Clinical and radiographic outcomes were compared between two groups. Furthermore, we evaluated the anterior femoral offset and initial contact state.

RESULTS

There were no significant differences in clinical or radiographic outcomes between two groups. CT data analysis and multiple regression analysis showed flexion alignment increased anterior femoral offset (AFO) and Gruen zone 4 contact area.

CONCLUSIONS

There was no significant difference in clinical or radiographic outcomes between flexion and neutral alignment of the tapered-wedge stem at an average of 4.7 years of follow-up. The increase of AFO and distal contact area in flexion alignment could affect the improvement of impingement-free range of flexion and intraoperative fracture.

Long-term results of total hip arthroplasty using Charnley Elite-Plus stem and the effect of stem geometry on radiographic distal femoral cortical hypertrophy

BACKGROUND

The Elite-Plus stem has two shape variations: roundback and flanged. The correlation between the radiographic results and stem geometry has not been previously investigated. The objective of this study was to evaluate the long-term primary total hip arthroplasty results using Elite-Plus stems, and the effect of stem geometry on radiographic distal femoral cortical hypertrophy.

METHODS

We retrospectively evaluated, radiographically, 156 patients (173 hips) who underwent total hip arthroplasty between April 1998 and November 2005, and were followed up for >5 years, postoperatively. Radiographic factors affecting distal femoral cortical hypertrophy were analysed using multivariable logistic regression analysis.

RESULTS

The mean follow-up period was 11.6 (5-17.8) years. During follow-up, femoral components were revised in 7 hips; one was revised due to aseptic loosening. Another femoral component was loosened and waiting for revision. The 10- and 15-year survival rates for aseptic stem loosening were 100% and 98.1% (95% CI: 92.5-99.5), respectively. Distal femoral cortical hypertrophy occurred in 23 hips (14.8%), and more often with roundback type (34.1%) than with flanged type (7.2%). Distal femoral cortical hypertrophy was observed in 34.8% of hips with valgus alignment, 11.3% with neutral alignment, and 12.5% with varus alignment. Multivariable logistic regression analysis showed that roundback stem shape and valgus stem alignment significantly affected the occurrence of distal femoral cortical hypertrophy.

CONCLUSIONS

The Elite-Plus stem has excellent long-term clinical and radiographic results in Japanese patients. The occurrence of distal femoral cortical hypertrophy significantly depends on the shape and alignment of Elite-Plus stems.

Short stem total hip arthroplasty: Potential explanations for persistent post-surgical thigh pain

Short stem uncemented femoral implants were developed with the aim of preserving proximal bone stock for future revisions, improving biomechanical reconstruction, aiding insertion through smaller incisions and potentially decreasing or limiting the incidence of thigh pain. Despite all the advantages of short stem designs, it remains unclear whether they are able to limit post-surgical thigh pain. In patients with short stem hip arthroplasty and persistent thigh pain, it is of the utmost importance to understand the potential etiologies of this chronic pain for selecting the appropriate treatment strategy. Therefore, this manuscript explores the hypothetical etiologies of persistent thigh pain in short stem total hip arthroplasty, including both peripheral factors (structural or biomechanical causes) and central factors (involvement of the central nervous system). First, intrinsic causes (e.g. aseptic femoral loosening and prosthetic joint infection) and extrinsic sources (e.g. muscle pathology or spinal pathology) of persistent thigh pain related to hip arthroplasty are explained. In addition, other specific peripheral causes for thigh pain related to the short stem prosthetic reconstruction (e.g. stem malalignment and micro-motion) are unraveled. Second, the etiology of persistent thigh pain after short stem hip arthroplasty is interpreted in a broader concept than the biomechanical approach where peripheral structural injury is believed to be the sole driver of persistent thigh pain. Over the past decades evidence has emerged of the involvement of sensitization of central nervous system nociceptive pathways (i.e. central sensitization) in several chronic pain disorders. In this manuscript it is explained that there might be a relevant role for altered central nociceptive processing in patients with persistent pain after joint arthroplasty or revision surgery. Recognition of a potential role for centrally-mediated changes in pain processing in total hip replacement surgery has important implications for treatment. Comprehensive treatment addressing peripheral factors as well as neurophysiological changes occurring in the nervous system may help to improve outcomes in patients with short stem hip arthroplasty and chronic thigh pain. Working within a biopsychosocial approach in orthopaedic surgery, specifically in relation to total hip arthroplasty, could be very important and may lead to more satisfaction. Further research is warranted.

Periprosthetic Occult Fractures of the Acetabulum Occur Frequently During Primary THA

BACKGROUND

Periprosthetic fractures of the acetabulum occurring during primary THA are rare. Periprosthetic occult fractures are defined as those not identified by the surgeon during the procedure which might be missed on a routine postoperative radiograph. However, it is unclear how frequently these fractures occur and whether their presence affects functional recovery.

QUESTIONS/PURPOSES

In this study, using routine CT scans that were obtained as part of another primary hip arthroplasty study protocol, we retrospectively assessed (1) the prevalence of occult fractures of the acetabulum occurring during primary THA, (2) the location of occult fractures of the acetabulum during THA, and (3) risk factors contributing to such occult fractures.

METHODS

Between 2004 and 2013, our institute performed 585 primary THAs (cementless or hybrid) in 494 patients with DICOM pre- and postoperative CT; during the period in question, all patients undergoing THA underwent CT before and after surgery. Preoperative CT images were taken as part of a CT-based three-dimensional templating software and navigation system. Postoperative CT images were taken an average of 1 week after surgery as part of a different protocol to evaluate cup position, restoration of leg length and offset, volume of postoperative hematoma to assess anticoagulation effects after THA, and fractures that were not found on routine postoperative radiographs (which we defined as occult fractures). Patients with a history of prior pelvic osteotomy, trauma, and infection were excluded (88 patients/99 hips); 406 patients (102 males and 304 females; 486 hips) form the basis of this report. The mean age of the patients was 60 ± 11 years, with a mean BMI of 23 ± 4 kg/m2. The mean followup of the patients with periprosthetic fracture of the acetabulum was 58 ± 28 months (range, 12-131 months). Potential risk factors for occult acetabular fracture including age, sex, BMI, preoperative diagnosis, additional dome screw fixation, composition and size of each cup, and acetabular design were examined in multivariate analysis. Acetabular component designs were categorized as true hemispheric, peripheral self-locking, and elliptical; during the period in question the indications for each cup design were based on the brand of stem used. Comparison between preoperative and postoperative CT images was done to detect the fractures. Patients with fractures identified during surgery were treated with additional dome screw fixation and a 3-week period of nonweightbearing. Patients with occult fractures in this series did not receive additional treatment as we had confirmed secure fixation of the cup during surgery.

RESULTS

Occult fractures occurred in 41 hips (8.4%); periprosthetic fractures of the acetabulum were seen during surgery in an additional two hips (0.4%). The superolateral wall was the most frequent location for occult fractures of the acetabulum. After controlling for relevant confounding variables, only the use of peripheral self-locking cups was associated with an increased risk of occult fracture (odds ratio [OR], 2.6 compared with hemispheric cups; 95% CI, 1.2-5.6; p < 0.05). All patients with occult fractures showed bone ingrowth fixation at the final followup, without any additional surgical intervention.

CONCLUSIONS

Periprosthetic occult fractures of the acetabulum may occur relatively frequently during press-fit impaction. We observed a higher rate of fractures associated with the use of peripheral self-locking components. Occult acetabular fractures not detected on routine postoperative plain films may be ignored if secure fixation of the cup has been confirmed during the operation.

LEVEL OF EVIDENCE

Level III, therapeutic study.