Comparative evaluation of cone beam CT and micro-CT on blooming artifacts in human teeth filled with bioceramic sealers

Optimization of photon counting CT for cardiac imaging in patients with left ventricular assist devices: An in-depth assessment of metal artifacts

PURPOSE

Photon counting CT (PCCT) holds promise for mitigating metal artifacts and can produce virtual mono-energetic images (VMI), while maintaining temporal resolution, making it a valuable tool for characterizing the heart. This study aimed to evaluate and optimize PCCT for cardiac imaging in patients during left ventricular assistance device (LVAD) therapy by conducting an in-depth objective assessment of metal artifacts and visual grading.

METHODS

Various scan and reconstruction settings were tested on a phantom and further evaluated on a patient acquisition to identify the optimal protocol settings. The phantom comprised an empty thoracic cavity, supplemented with heart and lungs from a cadaveric lamb. The heart was implanted with an LVAD (HeartMate 3) and iodine contrast. Scans were performed on a PCCT (NAEOTOM Alpha, Siemens Healthcare). Metal artifacts were assessed by three objective methods: Hounsfield units (HU)/SD measurements (DiffHU and SDARTIFACT), Fourier analysis (AmplitudeLowFreq), and depicted LVAD volume in the images (BloomVol). Radiologists graded metal artifacts and the diagnostic interpretability in the LVAD lumen, cardiac tissue, lung tissue, and spinal cord using a 5-point rating scale. Regression and correlation analysis were conducted to determine the assessment method most closely associated with acquisition and reconstruction parameters, as well as the objective method demonstrating the highest correlation with visual grading.

RESULTS

Due to blooming artifacts, the LVAD volume fluctuated between 27.0 and 92.7 cm3. This variance was primarily influenced by kVp, kernel, keV, and iMAR (R2 = 0.989). Radiologists favored pacemaker iMAR, 3 mm slice thickness, and T3D keV and kernel Bv56f for minimal metal artifacts in cardiac tissue assessment, and 110 keV and Qr40f for lung tissue interpretation. The model adequacy for DiffHU SDARTIFACT, AmplitueLowFreq, and BloomVol was 0.28, 0.76, 0.29, and 0.99 respectively for phantom data, and 0.95, 0.98, 1.00, and 0.99 for in-vivo data. For in-vivo data, the correlation between visual grading (VGSUM) and DiffHU SDARTIFACT, AmplitueLowFreq, and BloomVol was -0.16, -0.01, -0.48, and -0.40 respectively.

CONCLUSION

We found that optimal scan settings for LVAD imaging involved using 120 kVp and IQ level 80. Employing T3D with pacemaker iMAR, the sharpest allowed vascular kernel (Bv56f), and VMI at 110 keV with kernel Qr40 yields images suitable for cardiac imaging during LVAD-therapy. Volumetric measurements of the LVAD for determination of the extent of blooming artifacts was shown to be the best objective method to assess metal artifacts.

The effect of voxel and field of view size on the volumetric alteration artifact of high-density materials with 2 cone beam computed tomography devices

OBJECTIVE

We investigated the influence of voxel and field of view (FOV) sizes on expression of the volumetric alteration artifact (VAA) of 5 high-density materials in 2 cone beam computed tomography (CBCT) devices.

STUDY DESIGN

Cylinders of amalgam, cobalt-chromium, gutta-percha, titanium, and zirconium were individually positioned in a polymethyl methacrylate phantom. OP300 Maxio and ProMax 3D Classic CBCT devices were used to acquire images with varying voxel and FOV sizes, totaling 585 scans. Two evaluators segmented the high-density cylinder images to obtain the tomographic volumes. The difference between the tomographic and physical volume of each cylinder (i.e., volumetric alteration) was calculated. Statistical analysis was conducted with multiway ANOVA and the Tukey post hoc test (α = 5%). Evaluator reliability was measured with the intraclass correlation coefficient (ICC).

RESULTS

All studied parameters and nearly all interactions influenced the VAA (P < .05). The post hoc test demonstrated less volumetric alteration for the smallest voxel sizes, 61 × 78 mm FOV, and gutta-percha for OP300, and for the smallest voxel sizes, 80 × 80 mm FOV, and gutta-percha and titanium for ProMax 3D (P < .05). The ICC demonstrated perfect reliability (1.00).

CONCLUSIONS

Voxel and FOV sizes influenced VAA expression. Using smaller voxel sizes, the 61 × 78 mm FOV for OP300 and the 80 × 80 mm FOV for ProMax 3D, and materials with lower density and lower atomic number reduced VAA expression.

High-density objects in exomass affect the volume of high-density objects inside the field of view

OBJECTIVES

To evaluate the effect of the presence and the number of high-density objects in the exomass on the volume of a high-density object in cone-beam CT (CBCT).

METHODS

Cylinders of cobalt-chromium (Co-Cr), titanium (Ti), and zirconium (Zi) were inserted into a polymethylmethacrylate phantom in five different combinations of number and position: 1-no cylinder; 2-one cylinder in a posterior region; 3-one cylinder in an anterior region; 4-two cylinders in posterior regions; and 5-three cylinders in anterior and posterior regions. The phantom underwent CBCT scanning using OP300 and X800 systems, with the afore mentioned cylinders of the same composition placed in the exomass and an additional high-density cylinder placed in the centre of the field of view (FOV), corresponding to the left-anterior region. The tomographic volume of the cylinder inside the FOV was measured using semi-automatic segmentation. The volumetric alteration (VA) between the segmented and physical volumes, in percentage, was compared among the experimental groups using repeated measures ANOVA and Tukey post-hoc (α = 5%).

RESULTS

The factors material, combination, and their interaction affected the volume or both CBCT systems. In OP300, more cylinders in the exomass reduced the VA, mainly for Co-Cr. In X800, more cylinders in the exomass tended to increase the VA inside the FOV, except for Zi.

CONCLUSIONS

In general, the presence of high-density objects in the exomass influences the VA of the object inside the FOV, although this oscillates according to object composition, number and position in the exomass, and CBCT system.

Global cone-beam computed tomography adoption, usage and scan interpretation preferences of dentists and endodontists

AIM

This study investigated the adoption of cone-beam computed tomography (CBCT) by dentists and endodontists around the world, including their preferences in endodontic CBCT usage.

METHODOLOGY

An online questionnaire surveyed dental association members in Australia and New Zealand, and endodontic association members in Australia, Britain, Canada, Italy, New Zealand and the USA, about their CBCT training history, considerations in acquisition/interpretation, access to and usage of CBCT, preferred scan interpreter, and preferred endodontic scan settings. Data were analysed with Chi-squared, independent sample t-tests, Cochran's Q and McNemar's tests.

RESULTS

Responses from 578 endodontic specialists or postgraduates (Group E) and 185 non-endodontic dentists (Group NE) were included. Continuing professional education (CPE) was the most common source of CBCT training (69.2%). Factors considered in CBCT acquisition/interpretation included beam hardening (75.4%), radiation exposure (61.1%) and patient movement (58.3%). Group E reported higher CBCT usage (90.8%) than Group NE (45.4%, p < .001) and greater workplace access to CBCT (81.1% vs. 25.9%, p < .001). Scans were interpreted by the respondent in most workplace scans (83.3%) and externally taken scans (60.5%); Group E were significantly more likely to interpret themselves than Group NE. Small field of view (83.6%) and high resolution (86.6%) were most preferred as settings for endodontic CBCTs; Group NE were less likely to choose these settings. There were some geographic variations within Group E.

CONCLUSIONS

CBCT training was most commonly acquired via CPE. Endodontic respondents reported very high CBCT usage and access in the workplace. There are educational implications regarding CBCT limitations, appropriate applications and interpretation.

Assessment of the root filling volume in C-shaped root canal on cone-beam CT and micro-CT in relation to nano-CT

AIM

To assess the observed volume of filled C-shaped root canals from different CBCT and micro-CT having nano-CT as a reference.

MATERIALS AND METHODS

Twelve extracted mandibular molars with C-shaped root canals were endodontically treated using Reciproc Blue R25 (VDW GMBH, Munich, Germany) in a reciprocating system and filled with gutta-percha (Dentsply Maillefer) and AH Plus sealer (Dentsply DeTrey, Konstanz, Germany). CBCT scans were performed using 3 units-3D Accuitomo 170 (J. Morita, Kyoto, Japan), ProMax 3D Max (Planmeca, Helsinki, Finland), and NewTom VGi EVO (Cefla QR, Verona, Italy)-at two resolution modes: standard and high. Micro-CT and nano-CT scans were also obtained. The volume of all filled C-shaped root canals was obtained using CTAn software (Bruker, Kontich, Belgium), and the blooming artifact, in relation to nano-CT volume, was calculated. The data were evaluated by the Bland-Altman plots and ANOVA two-way for repeated measures (α = 0.05).

RESULTS

All CBCT units and micro-CT showed significantly larger observed volume of root canal filling when compared to nano-CT. The blooming artifact of root canal filling in standard resolution was significantly larger than that in high resolution (p < 0.05) in all CBCT units.

CONCLUSIONS

Endodontic filling material with AH Plus sealer causes blooming artifacts in CBCT units and micro-CT.

CLINICAL RELEVANCE

Considering the anatomical complexity of C-shaped root canals and the challenges associated with endodontic treatment, CBCT is frequently recommended for follow-up evaluations. However, the presence of endodontic filling material can result in blooming artifacts that may potentially impact the accurate diagnosis of endodontic complications.

Does cone-beam CT convex triangular field of view influence the image shape distortion of high-density materials?

OBJECTIVES

To assess the distortion of high-density materials using two CBCT devices presenting convex triangular and cylindrical fields of view (FOVs).

METHODS AND MATERIALS

Four high-density cylinders were individually placed in a polymethylmethacrylate phantom. 192 CBCT scans were acquired using the convex triangular and cylindrical FOVs of Veraviewepocs® R100 (R100) and Veraview® X800 (X800) devices. Using HorosTM's software, two oral radiologists determined the cylinders' horizontal and vertical dimensional alterations. Nine oral radiologists subjectively identified each cylinder's axial shape distortion. Statistical analysis comprised Multiway ANOVA (α = 5%), and the Kruskal-Wallis test.

RESULTS

The distortion in the axial plane was greater in the convex triangular FOVs for both devices in almost all the materials (p < 0.05). The evaluators subjectively identified a shape distortion in both FOVs for R100 device (p < 0.001), while no distortion was identified for X800 device (p = 0.620). A vertical magnification of all materials was observed in both FOVs for both devices (p < 0.05). No differences among vertical regions (p = 0.988) nor FOVs (p = 0.544) were found for the R100 device, while all materials showed higher magnification in all regions in the cylindrical FOV (p < 0.001) of the X800 device.

CONCLUSIONS

The convex triangular FOV influenced the axial distortion of the high-density materials in both devices. A vertical magnification was observed in both FOVs of both devices, but it was greater in the cylindrical FOV of the X800 device.

Quantitative evaluation of artifact expression in conebeam computed tomography of mesoporous calcium silicate nanoparticles as a promising root canal sealer

OBJECTIVES

We aimed to quantitatively compare the area and volume of artifacts in cone beam computed tomography produced by mesoporous calcium silicate nanoparticles (MCSNs), AH Plus sealer, and iRoot SP sealer when used as root canal sealers.

METHODS

We prepared 40 single-rooted mandibular premolars and divided them into an MCSN sealer group, an AH Plus sealer group, an iRoot SP sealer group, and a no-sealer (control) group. We filled the canals with gutta-percha using the single-cone method and subjected them to conebeam computed tomography before and after the placement of root fillings using the same exposure parameters. We evaluated the images to quantify the areas of hyperdense and hypodense artifacts and non-affected teeth and reconstructed 3-dimensional image models of the materials to study volume distortion artifacts.

RESULTS

The MCSN sealer group produced a significantly smaller hyperdense and volume distortion artifacts than the AH Plus and iRoot SP groups (P < .01), but the area and volume of hypodense artifacts did not differ significantly among the groups (P > .05).

CONCLUSIONS

When used as a root canal sealer, MCSNs generate a significantly smaller area and volume of hyperdense artifacts than AH Plus and iRoot SP sealers. By significantly reducing the generation of high-density artifacts, MCSNs may facilitate the evaluation of root canal filling quality and the diagnosis of root canal abnormalities.

Biocompatibility, bioactive potential, porosity, and interface analysis calcium silicate repair cements in a dentin tube model

OBJECTIVES

This study is to evaluate biocompatibility, bioactive potential, porosity, and dentin/material interface of Bio-C Repair (BIOC-R), MTA Repair HP (MTAHP), and Intermediate Restorative Material (IRM).

MATERIALS AND METHODS

Dentin tubes were implanted into subcutaneous of rats for 7, 15, 30, and 60 days. Thickness of capsules, number of inflammatory cells (ICs), interleukin-6 (IL-6), osteocalcin (OCN), and von Kossa were evaluated. Porosity and material/dentin interface voids were also analyzed. Data were submitted to ANOVA and Tukey's tests (p < 0.05).

RESULTS

IRM capsules were thicker and contained greater ICs and IL-6-immunopositive cells at 7 and 15 days. BIOC-R capsules exhibited higher thickness and ICs at 7 days and greater IL-6 at 7 and 15 days than MTAHP (p < 0.05). At 30 and 60 days, no significant difference was observed among the groups. OCN-immunopositive cells, von Kossa-positive, and birefringent structures were observed in BIOC-R and MTAHP. MTAHP exhibited higher porosity and interface voids (p < 0.05).

CONCLUSIONS

BIOC-R, MTAHP, and IRM are biocompatible. Bioceramics materials demonstrate bioactive potential. MTAHP presented the highest porosity and presence of voids.

CLINICAL RELEVANCE

BIOC-R and MTAHP have adequate biological properties. BIOC-R demonstrated lower porosity and presence of voids, which may represent better sealing for its clinical applications.

In vitro evaluation of the sealing ability of combined use of iRoot BP Plus and iRoot SP for root-end filling

OBJECTIVES

The aim of this in vitro study was to evaluate the sealing ability of combined application of iRoot BP Plus Root Repair Material (BP-RRM) and iRoot SP Injectable Root Canal Sealer (SP-RCS) for root-end filling.

MATERIAL AND METHODS

A total of 120 extracted human teeth were used in this study and were randomly divided into four groups. The BP-RRM+SP-RCS group included teeth retro-filled with combined use of BP-RRM and SP-RCS (n=45), and the BP-RRM group included teeth retro-filled by BP-RRM alone (n=45). Teeth without root-end preparation and filling were equally divided into positive control (n=15) and negative control (n=15). The apical sealing ability was evaluated by micro-CT analysis, dye penetrant examination, bacterial leakage test, and glucose leakage test.

RESULTS

Micro-CT analysis showed that the total void fraction of BP-RRM+SP-RCS group was significantly lower than that of BP-RRM group, particularly at the coronal 1/3 segment of the retro-filled roots. Consistently, the maximum linear depth of dye leakage in BP-RRM+SP-RCS group was less than that of BP-RRM group. Bacterial leakage test showed that the microbial leakage in BP-RRM+SP-RCS group was significantly less than that in BP-RRM group. However, no significant difference in glucose leakage between BP-RRM+SP-RCS group and BP-RRM group was observed.

CONCLUSION

Combined use of BP-RRM and SP-RCS for root-end filling promotes apical sealing in vitro.

CLINICAL RELEVANCE

Combined use of BP-RRM and SP-RCS for root-end filling exhibited better apical sealing as compared to BP-RRM alone in vitro, and this may help reducing technical sensitivity and promoting clinical efficiency during endodontic microsurgery.

Antibacterial activity and physicochemical properties of a sealer containing copaiba oil

This study aimed to evaluate the antimicrobial activity and physicochemical properties of a novel dual-cure endodontic sealer containing copaiba oil. The copaiba oil was obtained and characterized by gas chromatography (GC), and the minimum inhibitory concentration (MIC) was performed. The experimental sealers were formulated with copaiba oil concentrations of 0, 0.5, 1, and 2%, and the RealSeal™ (Sybron endo, Orange, USA) and AH Plus (Dentsply De Trey Gmbh, Konstanz, Germany) were used as the commercial references. The antimicrobial activity of the sealers was evaluated by the direct contact test for 1h and 24h. To evaluate the physicochemical properties of the sealers, the degree of conversion, setting time, film thickness, dimensional stability, and radiopacity tests were performed. The data were statistically analyzed by one-way ANOVA and Tukey's test (α = 0.05). Concerning the results, the sealers containing copaiba oil showed antimicrobial activity without harming the physicochemical properties.

A perspective on the diagnosis of cracked tooth: imaging modalities evolve to AI-based analysis

Despite numerous clinical trials and pre-clinical developments, the diagnosis of cracked tooth, especially in the early stages, remains a challenge. Cracked tooth syndrome is often accompanied by dramatic painful responses from occlusion and temperature stimulation, which has become one of the leading causes for tooth loss in adults. Current clinical diagnostical approaches for cracked tooth have been widely investigated based on X-rays, optical light, ultrasound wave, etc. Advances in artificial intelligence (AI) development have unlocked the possibility of detecting the crack in a more intellectual and automotive way. This may lead to the possibility of further enhancement of the diagnostic accuracy for cracked tooth disease. In this review, various medical imaging technologies for diagnosing cracked tooth are overviewed. In particular, the imaging modality, effect and the advantages of each diagnostic technique are discussed. What's more, AI-based crack detection and classification methods, especially the convolutional neural network (CNN)-based algorithms, including image classification (AlexNet), object detection (YOLO, Faster-RCNN), semantic segmentation (U-Net, Segnet) are comprehensively reviewed. Finally, the future perspectives and challenges in the diagnosis of the cracked tooth are lighted.

Precision medicine using patient-specific modelling: state of the art and perspectives in dental practice

The dental practice has largely evolved in the last 50 years following a better understanding of the biomechanical behaviour of teeth and its supporting structures, as well as developments in the fields of imaging and biomaterials. However, many patients still encounter treatment failures; this is related to the complex nature of evaluating the biomechanical aspects of each clinical situation due to the numerous patient-specific parameters, such as occlusion and root anatomy. In parallel, the advent of cone beam computed tomography enabled researchers in the field of odontology as well as clinicians to gather and model patient data with sufficient accuracy using image processing and finite element technologies. These developments gave rise to a new precision medicine concept that proposes to individually assess anatomical and biomechanical characteristics and adapt treatment options accordingly. While this approach is already applied in maxillofacial surgery, its implementation in dentistry is still restricted. However, recent advancements in artificial intelligence make it possible to automate several parts of the laborious modelling task, bringing such user-assisted decision-support tools closer to both clinicians and researchers. Therefore, the present narrative review aimed to present and discuss the current literature investigating patient-specific modelling in dentistry, its state-of-the-art applications, and research perspectives.

Quantitative Analysis of Cone-Beam Computed Tomography Artifacts Induced by Nonmetallic Root Canal Filling Materials Using Different Fields of View: In Vitro Study

Cone-beam computed tomography (CBCT) imaging artifacts can hinder accurate diagnosis of several conditions. The aim of this study was to quantify CBCT artifacts created by nonmetallic root canal filling materials using two fields of view (FOV). Root canals of twenty extracted maxillary central incisors (n = 20) were instrumented and randomly divided into four equal groups: canals in Group 1 were filled with gutta-percha, canals in Group 2 with mineral trioxide aggregate (MTA) and gutta-percha, canals in Group 3 with gutta-percha and glass-fiber posts, and canals in Group 4 with MTA and glass-fiber posts. Each tooth was mounted on a silicon block and scanned three times using a CBCT machine, first with a prefilling scan (control) and then with postfilling scans, using two different FOV (40∗50 mm and 80∗50 mm). Imaging software was used to measure grayscale pixel values of canal cross sections. Data were analyzed using t-test and paired t-test statistical tests, with statistical significance set at p ≤ 0.05. Dentin at the apical and middle third of the teeth showed a significant decrease in minimum grayscale values in association with gutta-percha (p = 0.027, p = 0.034). However, a wide 80∗50 FOV showed a significant increase in maximum grayscale values of coronal (p = 0.048) and apical dentin (p = 0.049). Glass-fiber posts in middle third cross sections also corresponded to an increase in maximum grayscale values (p = 0.018). Gutta-percha produced dark band artifacts in the root's middle and apical thirds, whereas white streak artifacts were produced by gutta-percha in the coronal third and glass-fiber posts in the coronal and middle thirds when imaged with a wider FOV. A smaller FOV is therefore recommended for CBCT imaging, as it produces fewer artifacts.

Influence of endodontic sealers artifacts in the detection of vertical root fractures

Abstract The aim of this study was to compare the influence of endodontic sealers artifacts on the detection of vertical root fracture in cone beam computed tomography (CBCT). Premolars and central incisors were assigned into five different groups: Control, Pulp Canal Sealer, AH Plus, Sealer 26, and BC Sealer (n= 10, per group). VRFs were mechanically induced and the teeth were inserted into an image phantom. Subsequently, CBCT (Cranex 3Dx, Soredex, Tuusula, Finland) images were obtained and two observers were asked separately to identify root fracture, by visual analysis. For both premolar and central incisors, kappa coefficients of intraobserver agreement varied from good to excellent (K: 80% - 87%), and the values for interobserver agreement varied from fair to moderate (K: 30% - 35%). As follows, the area under the curve (AUC) of receiver operating characteristic (ROC) values for VRFs highlighted that the use of BC sealer reduced the observers’ ability to discriminate VRFs relative to other sealers. Moreover, sensitivity values for premolars teeth ranged from 20% to 60%, and specificity ranged from 60% to 100%; while sensitivity values for central incisors ranged from 30% to 70%, and specificity ranged from 70% to 100%. In conclusion, the low sensitivity values, mainly for premolars, demonstrated the difficulty in VRF diagnosis. Furthermore, BC Sealer induced significantly more imaging artifacts than other sealers. These results highlighting that endodontic sealers may interfere with the diagnosis of VRFs.

Longitudinal craze line propagation in human root dentin after instrumentation with NiTi rotary files of different instrument tapers after long-term chewing simulation

Objectives

The aim of this study was to investigate whether file design and taper significantly influence microcrack initiation during machine preparation.

Materials and methods

Sixty extracted teeth with straight single canals were selected. The teeth were randomly assigned to four groups based on their root canal anatomy and the corresponding NiTi rotary file system (I, Mtwo; II, ProTaper Universal; III, F6 SkyTaper; control, no preparation and filling). The root canals of the experimental groups were filled using the single-cone technique. The tested teeth were all subjected to a mechanical chewing simulation with flat lead loading over a period of 3 years (corresponding to 150,000 cycles). The teeth were checked for dentinal defects (accumulative crack growth in length) under the digital microscope (Keyence VHX-5000) at time 0 (baseline prior to chewing simulation) and after 3, 6, 12, 24, and 36 months of loading. The cumulative crack increase was statistically analyzed using the Kruskal–Wallis test, Jonckheere–Terpstra test, and the Wilcoxon rank-sum test. The significance was set at p < 0.05.

Results

In contrast to preparation with greater-tapered instruments, ProTaper Universal (group II) and F6 SkyTaper (group III) instrumentation with the smaller tapered Mtwo files (group I) showed less accumulative propagation of craze lines (p < 0.05) at all time points.

Conclusion

Instruments with greater taper for root canal instrumentation should be used with care to avoid negative long-term effects in the form of propagation of dentinal defects over time. A positive cutting-edge angle and a smaller taper have a positive effect on a lower craze line development.

Clinical relevance

Instruments with a positive cutting-edge angle and a smaller taper are beneficial for the long-term preservation of dentinal tooth structure.

Complete Obturation-Cold Lateral Condensation vs. Thermoplastic Techniques: A Systematic Review of Micro-CT Studies

To prevent re-infection and provide a hermetic seal of the root canal system, an endodontist must aim to produce a void-free obturation. This review aimed to compare the completeness of root canal obturation between the two most prevalent methods-cold lateral condensation and warm gutta-percha techniques-using micro-CT (PROSPERO reg no. 249815).

MATERIALS AND METHODS

A search of Scopus, Embase, PubMed (Medline via PubMed), and Web of Science databases was done without any time restriction according to the PRISMA protocol. Articles that compared both techniques and were published in English were included. Data was extracted and the risk of bias was assessed using an adapted tool based on previous studies.

RESULTS

A total of 141 studies were identified by the search. Following the screening and selection of articles, 9 studies were included for review. Data was extracted manually and tabulated. Most studies had a moderate risk of bias. None determined operator skill in both methods before comparison. The data extracted from the included studies suggests that both techniques produce voids in the obturation. The thermoplasticized gutta-percha techniques may result in fewer voids compared to cold lateral condensation.

CONCLUSION

Considering the limitations of the included studies, it was concluded that neither technique could completely obturate the root canal. Thermoplasticized gutta-percha techniques showed better outcomes despite a possible learning bias in favor of cold lateral condensation. Establishing operator skills before comparison may help reduce this bias.

Impact of the blooming artefact on dental implant dimensions in 13 cone-beam computed tomography devices

BACKGROUND

The purpose of this study was to objectively assess dimensional alteration (blooming artefact) on dental implant using 13 cone-beam computed tomography (CBCT) devices adjusted to device-specific scanning protocols and to assess whether subjective adjustment of brightness and contrast (B&C) could alter its visualization.

METHODS

An anthropomorphic phantom containing a dental implant was scanned in 13 CBCT devices adjusted to three scanning protocols: medium-FOV standard resolution, small-FOV standard resolution, and small-FOV high resolution. The diameter of the implant was measured at five levels, averaged, and compared with those from a reference standard industrial CT image. B&C adjustments were performed and measurements were repeated. The intraclass correlation coefficient assessed the reliability of the measurements and general linear mixed models were applied for multiples comparisons at a 95% confidence interval.

RESULTS

Implant diameter obtained from small-FOV high-resolution protocols in most CBCT devices was not significantly different when compared to that from the reference (p > 0.05). For standard protocols, significant dimensional alteration of the implant ranging from 23 to 34% (0.67 to 1.02 mm) was observed in 9 CBCT devices for small-FOV scanning (p < 0.05), and in 8 CBCT devices for medium-FOV scanning, implant dimensional alteration ranged significantly from 21 to 35% (0.62 to 1.04 mm). After B&C adjustments, dimensional alteration was reduced for several of the CBCT devices tested (p < 0.05).

CONCLUSIONS

The visualization of the implant dimensional alteration differed between CBCT devices and scanning protocols with an increase in diameter ranging from 0.27 to 1.04 mm. For most CBCT devices, B&C adjustments allowed to reduce visualization of implant blooming.

The influence of voxel size and artifact reduction on the detection of vertical root fracture in endodontically treated teeth

OBJECTIVE

The aim of this study was to evaluate the effect of voxel size and artefact reduction (AR) on the identification of vertical root fractures (VRFs) in endodontically treated teeth.

METHODS

A total of a hundred sound, extracted human mandibular single-rooted premolars were decoronated, after which root canal preparation was performed, canals were filled with gutta percha by single cone technique. Randomly selected fifty specimens were fractured, repositioned and glued together. The teeth were examined with cone beam computed tomography (CBCT) in five different voxel sizes (0.125, 0.200, 0.250, 0.300, and 0.400 voxels). Two scans were performed for each tooth, one with AR and one without AR. Two radiologists evaluated the CBCT scans.

RESULTS

All voxel dimensions were successful in detecting VRFs in CBCT scans. But as the voxel size increased, the percentage of detecting VRFs decreased. High accuracy, sensitivity, specificity and predictive values were found for VRF detection on CBCT scans. Accuracy and sensitivity values decreased (from 100 to 82) while voxel dimensions increased (from 0.125 to 0.400). High-resolution images (0.125, 0.200, and 0.250 voxels) caused an increase in sensitivity for detection of VRFs. AR did not affect the accuracy, sensitivity, specificity and predictive values for VRF detection on CBCT scans.

CONCLUSIONS

High-resolution CBCT images resulted in an increase in sensitivity and specificity for detection of VRFs compared with lower-resolution CBCT images. The use of AR did not further improve its diagnostic potential.

Evaluation of curved root canals filled with a new bioceramic sealer: A microcomputed tomographic study using images with different voxel sizes and segmentation methods

The aim of this study was to investigate the filling ability of a new premixed bioceramic sealer in comparison with an epoxy resin-based sealer in curved root canals using different segmentation methods and voxel sizes in micro-CT images. Twelve curved mesial roots of mandibular molars with two separated canals were selected. All root canals were prepared by using HyFlex EDM files size 25/.08 and filled by the single cone technique and Bio-C Sealer or AH Plus (n = 12). The samples were scanned by micro-CT at 5 μm. The images were analyzed at 5, 10, and 20 μm for the volumetric analysis of voids in filling. Visual image segmentation was performed by two examiners, and the automatic segmentation was accomplished for comparison. Radiopacity of the sealers was evaluated by radiographic analysis. Data were submitted to the two-way ANOVA and non-paired t tests at a significance level of 5%. AH Plus had the highest radiopacity (p < .05). Root canals filled with AH Plus or Bio-C had similar low percentage of voids (p > .05). There was no difference interobserver, which had similar results to those obtained with automatic segmentation for all voxel sizes evaluated (p > .05). Bio-C Sealer had appropriate filling ability. Visual and automatic segmentation can be applied to micro-CT images with voxel sizes from 5 to 20 μm to evaluate the filling of sealers with adequate radiopacity. Automatic segmentation should be used as a faster method.

Distortion or magnification? An in vitro cone-beam CT study of dimensional changes of objects with different compositions

OBJECTIVES

To assess whether dimensional changes occur as shape distortion (unevenly), contraction or magnification (evenly) in cone beam computed tomography (CBCT) considering materials, anatomical regions and metal artefact reduction algorithms.

METHODS

Four cylinders of amalgam (Am), cobalt-chromium (Co-Cr), gutta-percha (Gu), titanium (Ti) and zirconium (Zi) were inserted inside a polymethylmethacrylate phantom in anterior and posterior regions for acquisitions in Picasso Trio and OP300 with MAR enabled and disabled. Two observers measured the dimensions of each cylinder in three axes: Y (height), Z (antero posterior diameter) and X (latero-lateral diameter). Repeated measures ANOVA with Tukey post-hoc test compared the data (α = 5%).

RESULTS

Shape distortion occurred for all materials in anterior region of Picasso Trio without MAR (p < 0.05). With MAR enabled, Gu and Ti contracted (p ≥ 0.05), while the others showed distortion (p < 0.05). In posterior region, all materials distorted in both MAR conditions (p < 0.05), except Gu, which magnified without MAR (p ≥ 0.05) and contracted unevenly with MAR (p < 0.05). In anterior region of OP300, all materials magnified without MAR, (p ≥ 0.05) and had shape distortion with MAR (p < 0.05). In posterior region, only Am showed magnification without MAR (p ≥ 0.05), while all materials presented shape distortion with MAR (p < 0.05).

CONCLUSION

Dimensional changes of high-density materials in CBCT can be either a magnification, a contraction or a distortion; the last condition is the most prevalent. Furthermore, changes differ considering material, anatomical region and MAR condition.

Performance of Bioceramic-based Root Filling Material with Artifact Reduction Properties in the Detection of Vertical Root Fractures Using Cone-beam Computed Tomography

Introduction:

In Cone-beam Computed Tomography (CBCT) images, metallic artifacts by root filling materials reduce the quality of images. It seems that bioceramic sealers produce fewer artifacts than gutta-percha. In this situation, the possibility of VRF detection could increase, and therefore, flap and exploratory surgery would not be needed. The purpose of this study was to evaluate the performance of a bioceramic-based root filling material in the detection of Vertical Root Fractures (VRF) in CBCT imaging.

Materials and Methods:

This study was conducted at the dental school from March to August 2019, and 100 healthy human mandibular premolar teeth were obtained and randomly divided into two equal groups. The teeth were filled with either AH26 and gutta-percha or bioceramic root filling materials. VRF was induced on half of the decoronated teeth in each group using a Global Testing Machine, and the others were considered control. CBCT imaging was performed by the Cranex 3D machine. Comparisons of the 2 groups were made using the Mann-Whitney test.

Results:

There was a significant difference between the two groups of bioceramic and gutta-percha in the measured indices, including sensitivity (P=0.017), specificity (P=0.018), positive predictive value (P=0.018), negative predictive value (P=0.018), and accuracy (P=0.011). The Area Under Curve (AUC) also showed a significant difference between the two groups (P=0.011). According to Kappa test results, no significant difference was obtained between the findings of the two observers.

Conclusion:

Different root filling materials showed a different extent of artifact in CBCT images. Bioceramic root filling material induces fewer artifacts in CBCT images, and the diagnostic value of VRF in CBCT images in the root canals filled with it is greater than those filled with AH26 and gutta-percha.

Facial alveolar bone thickness and modifying factors of anterior maxillary teeth: a systematic review and meta-analysis of cone-beam computed tomography studies

BACKGROUND

Understanding the anatomy of the facial alveolar bone (FAB), provides a prognostic tool for estimating the degree of dimensional ridge alterations after tooth extraction. This systematic review and meta-analysis aims to determine the FAB thickness and modifying factors of anterior maxillary teeth measured by CBCT scans. A secondary objective was to assess the facial distance from the cementoenamel junction (CEJ) to the bone crest.

METHODS

An electronic search was made of Medline, Embase, Web of Science, Cochrane Library and Google Scholar up to December 2019. Studies that analyze and quantitatively compare FAB thickness at maxillary teeth by CBCT scans were included. The methodological quality of the included studies was appraised using the ROBINS-I tool and the overall meta-evidence certainty using the GRADE approach. A single means random-effects meta-analysis was performed to obtain the weighted mean for 95% confidence interval. A meta-regression of covariates and subgroup analysis was conducted. The nullity Qh test and I2 index for heterogeneity was estimated.

RESULTS

2560 potentially relevant articles were recorded from which 29 studies were selected for the qualitative analysis, including 17,321 teeth. Seventeen studies considered the facial bone crest, and 12 the CEJ as a reference point for their measurements. Mean FAB thickness was ≤ 1 mm in maxillary incisors and canines (0.75-1.05 mm) and 1-2 mm in premolars. Patients over 50 years of age, females and thin gingival phenotype was associated with thinner FAB at some apico-coronal locations of maxillary incisors and canines. The geographical setting was an effect modifier that could explain up to 87% of the heterogeneity in FAB thickness, being Asian populations that showed the lowest FAB thickness values. The CEJ-bone crest distance was 2-2.5 mm in all teeth analyzed. Population over 50 years of age exhibited greater CEJ-bone crest distances, and males also showed a trend for greater distance. Evidence certainty has shown moderate quality in most analysis subsets.

CONCLUSIONS

Facial alveolar bone at anterior maxillary teeth is thin, heterogeneous in width along its apico-coronal dimensions, and increases in thickness in maxillary premolars. The CEJ-bone crest distance presented homogeneous and similar values in all teeth analyzed.

Influence of CBCT-based volumetric distortion and beam hardening artefacts on the assessment of root canal filling quality in isthmus-containing molars

OBJECTIVES

To evaluate the influence of artefacts in cone beam CT (CBCT) images of filled root canals in isthmus-containing molars.

METHODS

10 teeth presenting canals with an isthmus were instrumented and filled with a thermoplasticised obturation technique. The teeth were scanned using a micro-CT device and two CBCT devices: 3D Accuitomo 170 (ACC) and NewTom VGi evo (NT), with different acquisition protocols: larger and smaller voxel size. Three examiners assessed the CBCT images for: (1) detection of filling voids; (2) assessment of under- or overestimation of the filling material and (3) resemblance of CBCT images to the reference standard. Analyses of Task 1 yielded accuracy, sensitivity and specificity for detection of filling voids. For tasks 2 and 3, statistical analysis was performed using Wilcoxon test. The level of significance was set at p < .05.

RESULTS

For Task 1, ACC showed higher sensitivity, whereas NT presented higher specificity. No significant difference was found between the protocols in ACC, however, for NT, differences between protocols were significant for all diagnostic values. In Task 2, visualisation of the filling was overestimated for NT, while for ACC, underestimation was observed. For Task 3, images with smaller voxel size were more similar to the reference image, for both CBCT devices.

CONCLUSIONS

Different artefacts compromise the detection of filling voids on CBCT images of canals in mandibular molars with isthmus. ACC and NT present rather similar diagnostic accuracy, even though artefact expression remains device-specific.

Development and properties of endodontic resin sealers with natural oils

OBJECTIVES

To synthesize and evaluate the physicochemical, antimicrobial, and cytocompatibility properties of experimental resin-based endodontic sealers containing butia or copaiba natural oils.

METHODS

Experimental groups contained butia (Butia capitata) at 0.5 % (B0.5), 1 % (B1), 2 % (B2), and copaiba (Copaifera spp.) at 0.5 % (C0.5), 1 % (C1), and 2 % (C2). The control group contained no added oils (experimental material, EM) and the commercial group was a methacrylate-based resin material (RealSeal™, SybronEndo Corporation, Orange, CA, USA). Degree of conversion, film thickness, setting time, flow, water sorption and solubility, and radiopacity were measured. Meanwhile, antimicrobial (modified direct contact test) and cytotoxicity assays of the experimental groups and controls were performed. One-way ANOVA was used to determine the effect of the independent variable (material) on the degree of conversion, film thickness, radiopacity, flow, setting time, water sorption and solubility, and cytotoxicity. For antimicrobial assays, data were analyzed using two-way ANOVA and Ŝidák's test.

RESULTS

The experimental groups containing natural oils showed higher values of degree of conversion, and lowest water sorption and solubility. EM, B0.5, B1, B2, and RS showed similar film thicknesses. The flow values were statistically similar in all groups. The experimental groups showed adequate cell compatibility. Copaiba oil at 2% increased the antimicrobial effect after 1 and 24 h (p < 0.05). The incorporation of butia or copaiba resulted in a slight modification in some physicochemical properties of the experimental resin sealers.

CONCLUSION

Novel resin sealers containing natural oils are a promising alternative for endodontics, because of their good physicochemical properties, antimicrobial effects, and cytocompatibility when compared to a commercially available sealer.

CLINICAL SIGNIFICANCE

Endodontic sealers containing butia or copaiba had satisfactory cytocompatibility, antimicrobial effects, and adequate physicochemical properties.

Biocompatibility of a High-Plasticity, Calcium Silicate-Based, Ready-to-Use Material

The Bio-C Sealer is a recently developed high-plasticity, calcium-silicate-based, ready-to-use material. In the present study, chemical elements of the materials were characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). The biocompatibility of the Bio-C Sealer was investigated using cytotoxicity tests and histological responses in the roots of dogs’ teeth. XRD, SEM, and FTIR produced hydrated calcium silicate in the presence of water molecules. In addition, FTIR showed the formation of calcium hydroxide and polyethylene glycol, a dispersing agent. The 1:4 dilutions of Bio-C Sealer presented weaker cytotoxicity than the Calcipex II in an in vitro system using the V-79 cell line. After 90 d, the periradicular tissue response of beagle dog roots was histologically evaluated. Absence of periradicular inflammation was reported in 17 of the 18 roots assessed with the Bio-C Sealer, whereas mature vertical periodontal ligament fibers were observed in the apical root ends filled with the Bio-C Sealer. Based on these results and previous investigations, the Bio-C Sealer is recommended as an effective root-end filling material. These results are relevant for clinicians considering the use of Bio-C Sealer for treating their patients.

Influence of windowing and metal artefact reduction algorithms on the volumetric dimensions of five different high-density materials: a cone-beam CT study

OBJECTIVE

To assess the influence of windowing and metal artefact reduction (MAR) algorithms on the volumetric dimensions of high-density materials using two CBCT systems.

METHODS

Four cylinders of amalgam, cobalt-chromium, gutta-percha, titanium and zirconium, were manufactured and their physical volumes (PV) were measured. A polymethyl methacrylate phantom containing the cylinders was submitted to CBCT acquisitions with Picasso Trio and OP300 units with their MAR enabled and disabled. The tomographic volume (TV) of all the cylinders was obtained by semi-automatic segmentation using two windowing adjustments: W1-large window width and upper window level; W2-narrow window width and low window level. Volumetric distortion was expressed as the difference between TV and PV. Statistics comprised intraclass correlation coefficient (ICC) and analysis of variance (ANOVA) for repeated measures with Tukey post hoc test (α = 5%).

RESULTS

The ICC values ​​indicated excellent reproducibility of TV. Gutta-percha and titanium resulted in the smallest volumetric distortion. Using W1 provided less volumetric distortion for almost all experimental conditions (p < 0.05). Activating MAR algorithm of Picasso Trio underestimated gutta-percha and titanium TV (p < 0.05) and was inefficient in significantly reducing the volumetric distortion of the other materials (p > 0.05). Disabling MAR algorithm of OP300 resulted in smaller volumetric distortion for almost all experimental conditions (p < 0.05).

CONCLUSIONS

The TV of gutta-percha and titanium were closer to the PV. In general, the MAR algorithms of both systems were inefficient in significantly reducing the volumetric distortion of high-density materials. We encourage the use of large window width and upper window level to evaluate high-density materials.

How image-processing parameters can influence the assessment of dental materials using micro-CT

Purpose

The aim of this study was to evaluate the influence of voxel size and different post-processing algorithms on the analysis of dental materials using micro-computed tomography (micro-CT).

Materials and Methods

Root-end cavities were prepared in extracted maxillary premolars, filled with mineral trioxide aggregate (MTA), Biodentine, and Intermediate Restorative Material (IRM), and scanned using micro-CT. The volume and porosity of materials were evaluated and compared using voxel sizes of 5, 10, and 20 µm, as well as different software tools (post-processing algorithms). The CTAn or MeVisLab/Materialise 3-matic software package was used to perform volume and morphological analyses, and the CTAn or MeVisLab/Amira software was used to evaluate porosity. Data were analyzed using 1-way ANOVA and the Tukey test (P<0.05).

Results

Using MeVisLab/Materialise 3-matic, a consistent tendency was observed for volume to increase at larger voxel sizes. CTAn showed higher volumes for MTA and IRM at 20 µm. Using CTAn, porosity values decreased as voxel size increased, with statistically significant differences for all materials. MeVisLab/Amira showed a difference for MTA and IRM at 5 µm, and for Biodentine at 20 µm. Significant differences in volume and porosity were observed in all software packages for Biodentine across all voxel sizes.

Conclusion

Some differences in volume and porosity were found according to voxel size, image-processing software, and the radiopacity of the material. Consistent protocols are needed for research evaluating dental materials.

A quantitative analysis of metal artifact reduction algorithm performance in volume correction with 3 CBCT devices

OBJECTIVE

The aim of this study was to quantitatively assess the performance of metal artifact reduction (MAR) algorithms on the volume of metal cylinders, considering the influence of materials, positions, and fields of view (FOVs), by using 3 cone beam computed tomography (CBCT) devices (NewTom VGi evo, Picasso Trio, and ProMax 3-D Max).

STUDY DESIGN

Nine phantoms containing cylinders of amalgam, copper-aluminum (CuAl) metal alloy, and titanium, combined in up to 3 positions, were scanned by using 2 different FOVs. MATLAB software was used to evaluate the differences between volumes before and after MAR application, and the possible interference of materials, positions, and FOVs. Wilcoxon's test and the Kruskal-Wallis test were used at a level of significance of 5%.

RESULTS

In general, images containing amalgam and CuAl showed a significant difference in volume before and after MAR application. However, no significant difference after MAR was observed (P > .05) relative to positions and FOVs. MAR had an impact on the cylinder volumes only in the NewTom VGi evo and ProMax 3-D Max scanners.

CONCLUSIONS

The performance of MAR algorithms in volume correction of metal objects is dependent on the materials and the CBCT unit.

Imaging of root canal treatment using ultra high field 9.4T UTE-MRI - a preliminary study

OBJECTIVES

To investigate the potential of 9.4T ultrashort echo time (UTE) technology visualizing tooth anatomy and root canal treatment in vitro. In particular, it was evaluated whether the currently achievable resolution is suited presenting all anatomical structures and whether the root canal filling materials are distinguishable in UTE-MRI.

METHODS

Four extracted human teeth were examined using 9.4T UTE-MRI prior endodontic treatment (native teeth), after preparation and after obturation procedure. Root canal obturation was performed using warm vertical compaction (Schilder technique) with an epoxy-resin-based sealer. A single gutta-percha cone measured by MRI served as intensity-reference. MRI results were validated with corresponding histologic sections of the teeth. In addition, all teeth were examined at the different stages with CBCT and conventional X-ray.

RESULTS

9.4T UTE-MRI enabled a precise visualization of root canal anatomy of all teeth at a resolution of 66 µm. After obturation, dentin, sealer and gutta-percha cones showed distinct MRI signal changes that allowed clear differentiation of the obturation materials from surrounding tooth structure. The filling materials, isthmal root canal connections and even dentin-cracks that were identified in the MR-images could be verified in histological sections.

CONCLUSIONS

9.4T UTE-MRI is suitable for visualization of root canal anatomy, the evaluation of root canal preparation and obturation with a high spatial resolution and may provide a versatile tool for dental material research in endodontics.

Evaluation of flow and filling of root canal sealers using different methodologies

Abstract Introduction Flow and filling ability of root canal sealers are indispensable for hermetic sealing of the root canal. Micro-computed tomography (micro-CT) can be used as a complementary methodology to evaluate such properties. Objective To evaluate the flow and filling ability of AH Plus, Endofill and Sealapex by conventional methodology and micro-CT. Material and method The flow of the sealers was analyzed according to ISO 6876/2012 and complemented by the area evaluation. Glass plates were manufactured with diameters of 1×1×2 mm and 1×1×1 mm (length, width and height), with a central cavity and four grooves in the horizontal and vertical directions. Each material was placed in the central cavity. Another glass plate and a metal weight were placed on the cement and kept for 10 minutes. The glass plate/sealer set was scanned using micro-CT. The flow was calculated by linear measurement of the material in the grooves. The central filling (mm3) was calculated in the central cavity and the lateral filling was measured up to 2 mm from the central cavity. Data were submitted to ANOVA/Tukey tests (α=0.05). Result All evaluated sealers presented flow according to ISO 6876 standards. The materials showed central cavity filling capacity higher than 80% and lateral filling greater than 75%. There was no difference in flow (mm and mm2) and in the filling ability (mm3) provided by the materials (p>0.05). Conclusion All evaluated root canal sealers showed adequate flow and filling capacity, suggesting their clinical application.