Increasing dental zirconia micro-retentive aspect through ultra-short pulsed laser microstructuring: study on flexural strength and crystal phase characterization

Effect of femtosecond laser induced surface patterns on the flexural strength of monolithic zirconia

To investigate how patterns generated by femtosecond (fs) laser and femtosecond laser power affect the surface roughness (Ra) and biaxial flexural strength (BFS) of monolithic zirconia. Eighty disk-shaped zirconia specimens were divided into eight subgroups (n = 10): Control (C), airborne-particle abrasion (APA), 400 mW fs laser (spiral [SP(400)], square [SQ(400)], circular [CI(400)]), and 700 mW fs laser ([SP(700)], [SQ(700)], [CI(700)]). Ra values were calculated by using a surface profilometer. One additional specimen per group was analyzed with scanning electron microscopy and x-ray diffractometry. BFS values were obtained by using the piston-on-3-ball test. One-way ANOVA and either Tukey's HSD (BFS) or Tamhane's T2 (Ra) tests were used to evaluate data (α = 0.05). Regardless of the pattern and power, fs laser groups had higher Ra than C and APA, while SP groups had lower Ra than CI and SQ groups (p ≤ 0.004). For each pattern, Ra increased with higher laser power (p < 0.001), while the laser power did not affect the BFS (p ≥ 0.793). CI and SQ groups had lower BFS than the other groups (p ≤ 0.040), whereas SP groups had similar BFS to C and APA (p ≥ 0.430). Fs laser microstructuring with spiral surface pattern increased the Ra without jeopardizing the BFS of zirconia. Thus, this treatment might be an option to roughen tested zirconia.

Intraoral Applications of Lasers in the Prosthetic Rehabilitation with Fixed Partial Dentures-A Narrative Review

Laser, an acronym for Light Amplification by Stimulated Emission of Radiation, is a powerful tool with diverse applications in modern dentistry. It emits monochromatic, coherent light resulting from photon-induced chain reactions. Available dental lasers include diode, argon, Er,Cr:YSGG, Er:YAG, Nd:YAG, and CO2. The unique property of these lasers, allowing them to be effectively used on both soft and hard tissues based on the operational parameters, positions them as particularly suited for a wide range of dental procedures. Compared to traditional methods, lasers offer advantages such as improved hemostasis and quicker wound healing. Such benefits stress the shift towards laser technology in dental treatment. In the realm of dental prosthodontics, which focuses on esthetics, functionality, and the physiological aspects of dental prostheses, lasers provide promising outcomes. Among the prosthetic options, fixed partial dentures stand out for their ability to mimic natural teeth, offering both esthetic and functional features, leading to satisfactory long-term outcomes if managed properly. This review paper delves into the specific application of laser technology in the context of prosthetic rehabilitation involving fixed partial dentures. By investigating intraoral laser procedures, it contributes to understanding laser's role in improving patients' satisfaction and clinical efficiency in this field.

An experimental study of flexural strength and hardness of zirconia and their relation to crown failure loads

STATEMENT OF PROBLEM

Dental zirconia is often marketed and selected for restorative use based upon the biaxial flexural strength of prefabricated specimens (disks) without considering other mechanical and physical properties.

PURPOSE

The purpose of this in vitro study was to test whether 4-point flexural strength, biaxial flexural strength, and/or hardness may correlate with failure loads for crowns made of different zirconia materials.

MATERIAL AND METHODS

Three brands of zirconia (BruxZir, Cercon, and Katana) were used to fabricate anatomically contoured crowns, rectangular bars, and circular disks. The sample size was n=15 specimens per zirconia brand and specimen shape. The bars were tested for 4-point flexural strength by using the 4-point bending (4PB) test and Vickers hardness (VH), while the disks were tested for biaxial flexural strength by using a piston-on-3 ball (POB) test. Crowns were attached to resin abutments and compressed with a steel spherical indenter through a polyethylene sheet to assess the failure loads by using the "crunch the crown" (CTC) test. One-way ANOVA (α=.05) was used to test for statistically significant differences between groups, and Weibull analysis was used to assess the variability of the measured flexural strengths, failure load, and hardness.

RESULTS

Statistical differences (P<.001) were found in comparing Cercon, BruxZir, and Katana ([4260 N=4186 N]>3195 N, respectively) with the CTC test and (396 MPa>[281 MPa=275 MPa], respectively) the 4PB test. No statistical differences (P=.084) were found among the zirconia brands (Cercon [384 MPa]=Bruxzir [359 MPa]=Katana [416 MPa]) for the POB test. No significant correlations (P>.05) were found between the 4PB, POB, or VH tests and the corresponding CTC test. The Weibull modulus varied for the different specimen geometries.

CONCLUSIONS

The piston-on-3 ball, 4-point bending, and Vickers hardness test results were not correlated with the corresponding crunch-the-crown test.

Qualitative SEM analysis of fracture surfaces for dental ceramics and polymers broken by flexural strength testing and crown compression

PURPOSE

To perform qualitative analysis using scanning electron microscopy (SEM) of fracture surfaces for ceramic and polymeric dental materials broken via standardized flexural and crunch-the-crown (CTC) tests.

MATERIALS AND METHODS

Zirconia, glass-ceramic, and polymeric (Trilor; TRI, Juvora; JUV, Pekkton; PEK) materials were loaded using crowns for CTC tests, discs (zirconia and glass-ceramics) for piston-on-3 ball tests, bars (polymer) for 3-point bend tests, and bars (zirconia, glass-ceramics) for 4-point bend tests. SEM was used to characterize the fracture surfaces and identify fracture surface features (e.g., origin, mist, hackle, and the direction of crack propagation [DCP]). Electron dispersive spectroscopy was used to identify the local chemistry.

RESULTS

Fracture surface features were found to be less visually apparent for glass-ceramics than zirconia. For zirconia bars, fractures originated roughly midway between the corner and center for processing defects related to sintering. Fractures originated at the bottom corners of glass-ceramic bars (void or surface flaw) and PEK bars (surface flaw). TRI bar failures exposed glassy fibers. Fracture features were generally less discernable for discs compared to bars for zirconia and glass-ceramics. Ceramic crowns fractured into 2 to 3 pieces, with fractures originating at the occlusal surface and clear evidence for the DCP. Failures of TRI and JUV specimens (bars and crowns) were less catastrophic than for the ceramics, with exposed fibers (TRI) and surface cracks (JUV). PEK crown and bar fractures presented dimple (ductile) features formed due to microvoid coalescence followed by brittle crack propagation.

CONCLUSIONS

The critical flaws responsible for failure initiation were a function of material composition and test configuration. Fractographic analysis can reveal problems associated with the manufacturing of materials, their handling, grinding and finishing/polishing procedures, the structural design and choice of material, and the quality of the final laboratory-delivered restoration.

Effect of different surface treatments on the biaxial flexural strength of zirconia ceramics

STATEMENT OF PROBLEM

Different surface treatments have been applied to zirconia restorations in clinical practice to increase the bond strength between zirconia and cement, but their effect on flexural strength is unknown.

PURPOSE

The purpose of this in vitro study was to evaluate the effect of different surface treatments before and after sintering on the flexural strength of zirconia.

MATERIAL AND METHODS

Sixty disk-shaped specimens with an initial diameter of 18.6 ±0.1 mm and thickness of 2 ±0.1 mm were prepared from preshaded presintered 3Y-TZP blocks. The specimens were randomly divided into 3 groups (n=20) according to surface treatments (Group Laser, Group APA, Group Rocatec), and the groups were then divided into 2 subgroups (n=10) according to surface treatment before and after sintering. The phase compositions of the groups were examined by using an X-ray diffractometer (XRD) with 3 randomly selected specimens from each group. Biaxial flexural strength testing was conducted using a universal testing machine to examine the flexural strength of the zirconia specimens. Two-way ANOVA and post hoc least significant difference tests were performed (α=.05).

RESULTS

According to the XRD analysis, no monoclinic phases were determined on the surface of the presintered laser-treated specimens, but tetragonal phases were observed on the surface of the postsintered specimens. Surface treatment type and application stage (presintering to postsintering) have a significant effect on the biaxial flexural strength of the specimens (P<.05). The lowest biaxial flexural values were observed in the Laser group, and postsintered specimens showed higher biaxial flexural strength than presintered specimens (P<.05).

CONCLUSIONS

Postsintered specimens showed higher monoclinic content than presintered specimens. Laser-treated specimens showed the lowest biaxial flexural strength for both presintered and postsintered specimens.