The effect of composition of solid silver amalgam electrodes on their electrochemical response

Selenium Supplementation Sensor Based on Direct Electrochemistry of Urinary Selenosugar and Total Selenium

Emerging point-of-care testing methods are extremely beneficial for personalized assessments of trace element metabolism including selenium (Se). Given the lack of timely evaluation methods for well-received Se fortification, an electrochemical solution was developed based on the recently identified urinary selenosugar (Sel) as a marker. The Se content of crude urine was rapidly determined (∼5 min), and the square-wave voltammetric responses of a Se-selective probe (SeSE) composed of liquid metal amalgam demonstrated comparable performance (e.g., detection limit: 19 nM) to central lab benchtop equipment within the physiological range. Meanwhile, SeSE enabled total urinary Se detection via a mere one-step oxidation. Additionally, SeSE was utilized to jointly assess the apparent internalization and utilization rate of two typical nutrients, selenite and selenomethionine, in a rat nutrition model, demonstrating consistent results with those obtained by HPLC-MS and ICP-MS. Upon systematic standardization directed by Ramaley's theory, SeSE was integrated into a battery-operated portable kit (dubbed "SeEye") with a micro electrochemical drive and tablet PC console for one-stop service trials in a local commercial scenario. This study establishes (1) a nutritive value classifier in a low-cost consumer electronic format and (2) noninvasive diagnostic technology for Se supplementation.

Enhanced sustainable electro-generation of a Ni (I) homogeneous electro-catalyst at a silver solid amalgam electrode for the continuous degradation of N2O, NO, DCM, and CB pollutants

This paper reports the sustainable and enhanced generation of a Ni(I) active electro-catalyst using AgSAE as a cathode material for the sustainable degradation of N₂O, NO, dichloromethane (DCM), and chlorobenzene (CB) by electroscrubbing in a series operation. The AgSAE electrode showed 1.66 times higher Ni(I) formation than the Ag metal electrode. The AgSAE achieved 20% ± 2% Ni(I) generation in a highly concentrated alkaline medium, whereas Ag metal only achieved 12% ± 2% Ni(I) generation at the same current density. Electrochemical impedance spectroscopy and voltammetric studies determined that the kinetics of the charge-transfer reaction was also preferential at the AgSAE, with the cathodic peak at -1.26 V vs. Ag/AgCl confirming Ni(I) formation. Initially, the change in the oxygen reduction potential and reduction efficiency of Ni(I) confirmed the removal of N₂O, NO, DCM and CB. In addition, the gas Fourier transform infrared (FTIR) spectrum revealed 99.8% removal efficiency of toxic pollutants. Therefore, the regeneration of Ni(I) confirmed the sustainable removal of toxic pollutants. Furthermore, the FTIR spectra revealed the formation of NH₃ during the reduction of N₂O and NO. On the other hand, DCM and CB were reduced to benzene derivatives in the solution phase. In addition, a plausible reduction mechanism was derived. As a result, the AgSAE cathode exhibited two-fold higher removal efficiency of N₂O, NO, DCM, and CB than the previously reported electrodes.

Electrospun metal oxide-TiO2 nanofibers for elemental mercury removal from flue gas

Nanofibers prepared by an electrospinning method were used to remove elemental mercury (Hg(0)) from simulated coal combustion flue gas. The nanofibers composed of different metal oxides (MO(x)) including CuO, In(2)O(3), V(2)O(5), WO(3) and Ag(2)O supported on TiO(2) have been characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), energy dispersing X-ray (EDX) and UV-vis spectra. The average diameters of these nanofibers were about 200nm. Compared to pure TiO(2), the UV-vis absorption intensity for MO(x)-TiO(2) increased significantly and the absorption bandwidth also expanded, especially for Ag(2)O-TiO(2) and V(2)O(5)-TiO(2). Hg(0) oxidation efficiencies over the MO(x)-TiO(2) nanofibers were tested under dark, visible light (vis) irradiation and UV irradiation, respectively. The results showed that WO(3) doped TiO(2) exhibited the highest Hg(0) removal efficiency of 100% under UV irradiation. Doping V(2)O(5) into TiO(2) enhanced Hg(0) removal efficiency greatly from 6% to 63% under visible light irradiation. Ag(2)O doped TiO(2) showed a steady Hg(0) removal efficiency of around 95% without any light due to the formation of silver amalgam. An extended experiment with 8 Hg(0) removal cycles showed that the MO(x)-TiO(2) nanofibers were stable for removing Hg(0) from flue gas. Factors responsible for the enhanced photocatalytic activities of the MO(x)-TiO(2) nanofibers were also discussed.

A Comparative Electrochemical Behaviour Study and Analytical Detection of the p-Nitrophenol Using Silver Solid Amalgam, Mercury, and Silver Electrodes

This work reports a comparative electrochemical behaviour study and p-nitrophenol analytical detection using silver solid amalgam, hanging dropping mercury, and silver electrodes. For this, square wave voltammetry was employed, where the analytical responses and the redox mechanisms could be compared for reduction processes of 4-nitrophenol by analysis of the voltammetric responses. The analytical performance of the electrode was evaluated and detection and quantification limits, recovery percentages, repeatability, and reproducibility for the silver solid amalgam and hanging dropping mercury electrodes presented similar values; the results presented for the silver electrode indicated worse analytical parameters than the other electrodes. The results indicate that the silver solid amalgam electrode can be considered a suitable tool and an interesting alternative for the analytical determination of 4-nitrophenol, as well as for the determination of other biological and environmentally interesting compounds that present analytical responses on mercury surfaces.