Preparation of polyacrylamide via surface-initiated electrochemical-mediated atom transfer radical polymerization (SI-eATRP) for Pb2+ sensing

Fabrication of high-performance cell-imprinted polymers based on AuNPs/MXene composites via metal-free visible light-induced ATRP

Cell-imprinted polymers (CIPs) for yeasts were fabricated via metal-free visible-light-induced atom transfer radical polymerization (MVL ATRP) on the surface of a glassy carbon electrode (GCE) which had been modified with gold nanoparticles (AuNPs)/MXene (Ti₃C₂T_x) composites. Here, the AuNPs/Ti₃C₂T_x composites form a macroporous structure, which could improve the electron transfer rate of the materials and facilitate the leaving or rebinding of cells. Methacrylic acid (MAA) and N,N'-methylene bis-acrylamide (MBA) were selected as the functional monomer and cross-linker of CIPs, because they could form efficient hydrogen bonding with mannan from yeast cell walls. The obtained electrode (CIPs/AuNPs/Ti₃C₂T_x/GCE) was characterized by electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). Further experiments indicated that the CIPs/AuNPs/Ti₃C₂T_x/GCE electrode could be utilized as an electrochemical biosensor to determine yeast cells by differential pulse voltammetry (DPV). The linear response range was 1.0 × 10² to 1.0 × 10⁹ cells per mL and the detection limit was 20 cells per mL (S/N = 3). The CIPs/AuNPs/Ti₃C₂T_x/GCE electrode also showed good selectivity, repeatability, reproducibility, and regeneration. Finally, the proposed sensor was used to detect yeast cells in commercial samples of Saccharomyces boulardii sachets by a standard addition method. The obtained recovery was from 96.9 to 104.8% showing its potential applications in clinical and diagnostic research.

Probing polymer brushes with electrochemical impedance spectroscopy: a mini review

Polymer brushes are frequently used as surface-tethered antifouling layers in biosensors to improve sensor surface-analyte recognition in the presence of abundant non-target molecules in complex biological samples by suppressing nonspecific interactions. However, because brushes are complex systems highly responsive to changes in their surrounding environment, studying their properties remains a challenge. Electrochemical impedance spectroscopy (EIS) is an emerging method in this context. In this mini review, we aim to elucidate the potential of EIS for investigating the physicochemical properties and structural aspects of polymer brushes. The application of EIS in brush-based biosensors is also discussed. Most common principles employed in these biosensors are presented, as well as interpretation of EIS data obtained in such setups. Overall, we demonstrate that the EIS-polymer brush pairing has a considerable potential for providing new insights into brush functionalities and designing highly sensitive and specific biosensors.

A novel electrochemical biosensor for lung cancer-related gene detection based on copper ferrite-enhanced photoinitiated chain-growth amplification

We reported an electrochemical biosensor via CuFe₂O₄-enhanced photoinitiated chain-growth polymerization for ultrasensitive detection of lung cancer-related gene. In this work, photoinitiated atom transfer radical polymerization (ATRP) was applied to amplify the electrochemical signal corresponding to lung cancer-related gene, and polymerization was triggered off under the illumination of blue light which was involved in copper-mediated reductive quenching cycle. At the same time, CuFe₂O₄-H₂O₂ system was also activated to enhance polymerization based on the photocatalysis of CuFe₂O₄, which was based on the reaction between •OH and methacrylic monomers to generate carbon-based radicals. Numerous ferrocene-based polymer was graft onto electrode surface through this amplification stages. The limit of detection was low to 1.98 aM (in 10 μL, ∼11.9 molecules) (R² = 0.998) with a wide linear range from 0.1 fM to 10 pM. This strategy made a good trade-off between cost-effectiveness and sensitivity, and it also presented a high selectivity and anti-interference. In addition, the operation was greatly simplified and detection time was also shortened, which endowed this electrochemical DNA biosensor great application potential.

Preparation of IgG imprinted polymers by metal-free visible-light-induced ATRP and its application in biosensor

Immunoglobulin G (IgG) is related to the occurrence of many diseases, such as measles and inflammatory. In this paper, IgG imprinted polymers (IgGIPs) were fabricated on the surface of nano Au/nano Ni modified Au electrode (IgGIPs/AuNCs/NiNCs/Au) via metal-free visible-light-induced atom transfer radical polymerization (MVL ATRP). The IgGIPs were prepared by IgG conjugated with fluorescein isothiocyanate (FITC-IgG) as both a template and a photocatalyst. After the templates were removed, the photocatalysts (FITC) would not remain in the polymer and avoided all the effect of catalysts on the electrode. The fabricated electrodes were examined by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS). Under the optimized conditions, IgGIPs/AuNCs/NiNCs/Au was prepared and used as an electrochemical biosensor. The biosensor could be successfully applied for the determination of IgG by differential pulse voltammetry (DPV) measurement. The results showed that the proposed biosensor displayed a broader linear range and a lower detection limit for IgG determination when it was compared to those similar IgG sensors. The linear range from 1.0 × 10^-6 mg L^-1 to 1.0 × 10¹ mg L^-1 was obtained with a low detection limit (LOD) of 2.0 × 10^-8 mg L^-1 (S/N = 3). Briefly, the biosensor in this study introduced an easy and non-toxic method for IgG determination and also provided a progressive approach for designing protein imprinted polymers.

Hydrophilic Surface Functionalization of Electrospun Nanofibrous Scaffolds in Tissue Engineering

Electrospun polymer nanofibers have received much attention in tissue engineering due to their valuable properties such as biocompatibility, biodegradation ability, appropriate mechanical properties, and, most importantly, fibrous structure, which resembles the morphology of extracellular matrix (ECM) proteins. However, they are usually hydrophobic and suffer from a lack of bioactive molecules, which provide good cell adhesion to the scaffold surface. Post-electrospinning surface functionalization allows overcoming these limitations through polar groups covalent incorporation to the fibers surface, with subsequent functionalization with biologically active molecules or direct deposition of the biomolecule solution. Hydrophilic surface functionalization methods are classified into chemical approaches, including wet chemical functionalization and covalent grafting, a physiochemical approach with the use of a plasma treatment, and a physical approach that might be divided into physical adsorption and layer-by-layer assembly. This review discusses the state-of-the-art of hydrophilic surface functionalization strategies of electrospun nanofibers for tissue engineering applications. We highlighted the major advantages and drawbacks of each method, at the same time, pointing out future perspectives and solutions in the hydrophilic functionalization strategies.

Immobilization of laccase onto modified PU/RC nanofiber via atom transfer radical polymerization method and application in removal of bisphenol A

In this study, 2-hydroxyethyl methacrylate (HEMA) was used as the monomers for surface grafting on electrospun PU/RC nanofiber membrane via atom transfer radical polymerization (ATRP) method, and the PU/RC-poly(HEMA) nanofiber membrane was investigated as a carrier for LAC. Free and immobilized LAC was characterized, and efficiency of bisphenol A (BPA) removal was determined. The results indicated that the PU/RC-poly(HEMA)-LAC showed relatively higher pH stability, temperature stability, and storage stability than free and PU/RC-LAC; moreover, more than 60% of the PU/RC-poly(HEMA)-LAC activity was retained after 10 cycles of ABTS treatment. Notably, the BPA removal efficiency of PU/RC-poly(HEMA)-LAC membrane generally ranged from 87.3 to 75.4% for the five cycles. Therefore, the PU/RC-poly(HEMA) nanofiber membrane has great potential as a carrier for the LAC immobilization for various industrial applications and bioremediation.

Under pressure: electrochemically-mediated atom transfer radical polymerization of vinyl chloride

Electrochemically mediated ATRP (eATRP) of vinyl chloride (VC), a less activated monomer, was successfully achieved. It is the first report on eATRP of a gaseous monomer under pressure.

Surface patterning of polyacrylamide gel using scanning electrochemical cell microscopy (SECCM)

Scanning electrochemical cell microscopy is introduced as a new tool for the synthesis and deposition of polymers on SAM-functionalised Au surfaces. The deposition of poly(N-hydroxyethyl acrylamide) is shown to be enhanced through the electrochemical generation of activating Cu(i)Cl/Me6TREN catalyst. Initiation of the polymerisation reaction is most likely due to in situ generation of reactive oxygen species following oxygen reduction.

Externally controlled atom transfer radical polymerization

ATRP can be externally controlled by electrical current, light, mechanical forces and various chemical reducing agents. The mechanistic aspects and preparation of polymers with complex functional architectures and their applications are critically reviewed.

Hydrophilicity and anti-fouling performance of polyethersulfone membrane modified by grafting block glycosyl copolymers via surface initiated electrochemically mediated atom transfer radical polymerization

In this study, we synthesize a modified polyethersulfone membrane to construct block copolymer brushes on the membrane surface.

Surface-Initiated Controlled Radical Polymerization: State-of-the-Art, Opportunities, and Challenges in Surface and Interface Engineering with Polymer Brushes

The generation of polymer brushes by surface-initiated controlled radical polymerization (SI-CRP) techniques has become a powerful approach to tailor the chemical and physical properties of interfaces and has given rise to great advances in surface and interface engineering. Polymer brushes are defined as thin polymer films in which the individual polymer chains are tethered by one chain end to a solid interface. Significant advances have been made over the past years in the field of polymer brushes. This includes novel developments in SI-CRP, as well as the emergence of novel applications such as catalysis, electronics, nanomaterial synthesis and biosensing. Additionally, polymer brushes prepared via SI-CRP have been utilized to modify the surface of novel substrates such as natural fibers, polymer nanofibers, mesoporous materials, graphene, viruses and protein nanoparticles. The last years have also seen exciting advances in the chemical and physical characterization of polymer brushes, as well as an ever increasing set of computational and simulation tools that allow understanding and predictions of these surface-grafted polymer architectures. The aim of this contribution is to provide a comprehensive review that critically assesses recent advances in the field and highlights the opportunities and challenges for future work.

Preparation of protein imprinted polymers via protein-catalyzed eATRP on 3D gold nanodendrites and their application in biosensors

Sensitive detection of metalloproteins is very essential in human pathologies.

Hydrophilicity and anti-fouling modification of polyethersulfone membrane by grafting copolymer chains via surface initiated electrochemically mediated atom transfer radical polymerization

Polyethersulfone membrane is modified by grafting copolymer chainsviathe SI-eATRP method for improvement of hydrophlicity and anti-fouling performance.