Artificial valves “up to date” in Japan

3D printed polyurethane prosthesis for partial tracheal reconstruction: a pilot animal study

A ready-made, acellular patch-type prosthesis is desirable in repairing partial tracheal defects in the clinical setting. However, many of these prostheses may not show proper biological integration and biomechanical function when they are transplanted. In this study, we developed a novel 3D printed polyurethane (PU) tracheal scaffold with micro-scale architecture to allow host tissue infiltration and adequate biomechanical properties to withstand physiological tracheal condition. A half-pipe shaped PU scaffold (1.8 cm of height, 0.18 cm thickness, and 2 cm of diameter) was fabricated by 3D printing of PU 200 μm PU beam. The 3D printed tracheal scaffolds consisted of a porous inner microstructure with 200 × 200 × 200 μm³ sized pores and a non-porous outer layer. The mechanical properties of the scaffolds were 3.21 ± 1.02 MPa of ultimate tensile strength, 2.81 ± 0.58 MPa of Young's modulus, and 725% ± 41% of elongation at break. To examine the function of the 3D printed tracheal scaffolds in vivo, the scaffolds were implanted into 1.0 × 0.7 cm² sized anterior tracheal defect of rabbits. After implantation, bronchoscopic examinations revealed that the implanted tracheal scaffolds were patent for a 16 week-period. Histologic findings showed that re-epithelialization after 4 weeks of implantation and ciliated respiratory epithelium with ciliary beating after 8 weeks of implantation were observed at the lumen of the implanted tracheal scaffolds. The ingrowth of the connective tissue into the scaffolds was observed at 4 weeks after implantation. The biomechanical properties of the implanted tracheal scaffolds were continually maintained for 16 week-period. The results demonstrated that 3D printed tracheal scaffold could provide an alternative solution as a therapeutic treatment for partial tracheal defects.

In vitro hydrodynamic evaluation of a biovalve with stent (tubular leaflet type) for transcatheter pulmonary valve implantation

We have been developing an autologous heart valve-shaped tissue with a stent (stent-biovalve) for transcatheter pulmonary valve implantation (TPVI) using "in-body tissue architecture" technology. In this study, the hydrodynamic performance of a stent-biovalve with tubular leaflets was evaluated by changing its leaflet height in an in vitro test in order to determine the appropriate stent-biovalve form for the pulmonary valve. A specially designed, self-expandable, stent-mounted, cylindrical acrylic mold was placed in a dorsal subcutaneous pouch of goat, and the implant was extracted 2 months later. Only the cylindrical acrylic mold was removed from the implant, and a tubular hollow structure of membranous connective tissue impregnated with the stent strut was obtained. Half of tubular tissue was completely folded in half inwards, and 3 commissure parts were connected to form 3 leaflets, resulting in the preparation of a stent-biovalve with tubular leaflets (25-mm ID). The stent-biovalve with adjusting leaflet height (13, 14, 15, 17, 20, and 25 mm) was fixed to a specially designed pulsatile mock circulation circuit under pulmonary valve conditions using 37 °C saline. The mean pressure difference and effective orifice area were better than those of the biological valve. The lowest and highest leaflet heights had a high regurgitation rate due to lack of coaptation or prevention of leaflet movement, respectively. The lowest regurgitation (ca. 11%) was observed at a height of 15 mm. The leaflet height was found to significantly affect the hydrodynamics of stent-biovalves, and the existence of an appropriate leaflet height became clear.

Utilization of star-shaped polymer architecture in the creation of high-density polymer brush coatings for the prevention of platelet and bacteria adhesion

We demonstrate utilization of star-shaped polymers as high-density polymer brush coatings and their effectiveness to inhibit the adhesion of platelets and bacteria. Star polymers consisting of poly(2-hydroxyethyl methacrylate) (PHEMA) and/or poly(methyl methacrylate) (PMMA), were synthesized using living radical polymerization with a ruthenium catalyst. The polymer coatings were prepared by simple drop casting of the polymer solution onto poly(ethylene terephthalate) (PET) surfaces and then dried. Among the star polymers prepared in this study, the PHEMA star polymer (star-PHEMA) and the PHEMA/PMMA (mol. ratio of 71/29) heteroarm star polymer (star-H71M29) coatings showed the highest percentage of inhibition against platelet adhesion (78-88% relative to noncoated PET surface) and Escherichia coli (94-97%). These coatings also showed anti-adhesion activity against platelets after incubation in Dulbecco's phosphate buffered saline or surfactant solution for 7 days. In addition, the PMMA component of the star polymers increased the scratch resistance of the coating. These results indicate that the star-polymer architecture provides high polymer chain density on PET surfaces to prevent adhesion of platelets and bacteria, as well as coating stability and physical durability to prevent exposure of bare PET surfaces. The star polymers provide a simple and effective approach to preparing anti-adhesion polymer coatings on biomedical materials against the adhesion of platelets and bacteria.