Atomic analysis and hardness measurement of the cavity prepared by laser

Microindentation hardness and calcium/phosphorus ratio of dentin following excavation of dental caries lesions with different techniques

BACKGROUND

The aim of this in vitro study was to evaluate the microindentation hardness and chemical composition of residual dentin left at the cavity bottom following removal of carious dentin using the Carisolv chemomechanical and Er:YAG laser caries excavation methods in comparison with the conventional tungsten-carbide bur excavation.

METHODS

Sixty-nine extracted permanent teeth with occlusal dentin caries were assigned into three groups according to caries removal technique. Carious dentin excavation was guided by tactile method and a caries-staining dye. In stereomicroscope images (100×) of the samples, the presence or absence of residual caries was defined. The Knoop hardness value of the cavity floor was determined and atomic analysis of treated cavities was performed by energy dispersive X-ray spectroscopy.

RESULTS

The Knoop hardness value of residual dentin left at the cavity bottom was lower (One-way ANOVA, Dunnett-C, p < 0.05) and the percentage of samples with remaining carious dentin was higher after Carisolv excavation than those obtained after conventional and laser excavations (Kruskal-Wallis, Mann-Whitney U, p < 0.05). No significant differences were found between the quantities of calcium content (Ca wt%), phosphorus content (P wt%) and calcium/phosphorus ratio of the cavities treated by three techniques (Kruskal-Wallis, Mann-Whitney U, p > 0.05).

CONCLUSION

The results indicated that Er:YAG laser was more comparable to conventional bur excavation than chemomechanical method in the efficacy of caries removal with regard to microindentation hardness of remaining dentin and both Carisolv gel and Er:YAG laser did not alter chemical composition of residual dentin in the treated cavities.

The effect of the angle of instrumentation of the Piezoelectric Ultrasonic Scaler on root surfaces

OBJECTIVES

To evaluate the influence of variations in the working angle of the piezoelectric ultrasonic scaler (PUS) on root surfaces.

MATERIAL AND METHODS

Fifty-five uniradicular bovine teeth were used, of which 25 teeth were used for the analysis of the roughness and root wear, while the remaining 30 teeth were used for the analysis of morphology (MRS) and the attachment of blood components (ABC). The teeth were randomly divided into five groups according to the type of treatment (G1-G5: piezoelectric ultrasonic scaler; G6: manual curette) and to the PUS working angle applied (G1: 0°; G2: 30°; G3: 45°; G4: 60°; G5: 90°). For statistical analysis, the data describing the MRS and ABC were analysed by the Kruskal-Wallis and Dunn's tests, and the data describing the roughness and tooth wear were analysed by anova and Tukey's tests at the significance level of 5%.

RESULTS

Manual curette (MC) promoted a smoother root surface than the application of the PUS. The PUS used at the angles of 30° and 45° resulted in a high level of ABC that was comparable to that obtained by MC. Additionally, the group in which the PUS was applied at an angle of 45° exhibited less tooth wear than the other groups.

CONCLUSIONS

Changes in the working angle of the PUS influenced the characteristics of root surfaces after instrumentation.

The effect of Nd:YAG and Er,Cr:YSGG lasers on the microhardness of human dentin

The current investigation determined the microhardness of dentin tissue irradiated with erbium, chromium-doped yttrium scandium gallium garnet (Er,Cr:YSGG) and neodymium-doped yttrium-aluminum garnet (Nd:YAG) lasers. Thirty non-carious human molars were used in this study. Dentin disks were prepared by horizontal sectioning of one third of the occlusal surface. Halves of dentin specimens were irradiated with 3.5- and 4.5-W Er,Cr:YSGG lasers and with a 2-W Nd:YAG laser. The remaining halves served as controls. The microhardness measurements were recorded with a Vickers surface microhardness tester. The results were statistically evaluated by paired t test and one-way ANOVA (p = 0.05). Laser irradiation has significantly reduced the microhardness of dentin within each group compared to its control. Moreover, statistically significant differences were observed among the different groups (p < 0.05). The 3.5-W Er,Cr:YSGG laser produced the greatest reduction in microhardness of dentin followed by 4.5 W and Nd:YAG laser. The differences between all the groups were statistically significant. It was concluded that both laser devices used in this study have resulted in significant thermal damage and subsequent reduction in dentin microhardness values.