Temperature imaging of laser-induced thermotherapy (LITT) by MRI: evaluation of different sequences in phantom

Estimation of the Proton Resonance Frequency Coefficient in Agar-based Phantoms

Aim

Agar-based phantoms are popular in high intensity focused ultrasound (HIFU) studies, with magnetic resonance imaging (MRI) preferred for guidance since it provides temperature monitoring by proton resonance frequency (PRF) shift magnetic resonance (MR) thermometry. MR thermometry monitoring depends on several factors, thus, herein, the PRF coefficient of agar phantoms was estimated.

Materials and Methods

Seven phantoms were developed with varied agar (2, 4, or 6% w/v) or constant agar (6% w/v) and varied silica concentrations (2, 4, 6, or 8% w/v) to assess the effect of the concentration on the PRF coefficient. Each phantom was sonicated using varied acoustical power for a 30 s duration in both a laboratory setting and inside a 3T MRI scanner. PRF coefficients were estimated through linear trends between phase shift acquired using gradient sequences and thermocouple-based temperatures changes.

Results

Linear regression (R 2 = 0.9707-0.9991) demonstrated a proportional dependency of phase shift with temperature change, resulting in PRF coefficients between -0.00336 ± 0.00029 and -0.00934 ± 0.00050 ppm/°C for the various phantom recipes. Weak negative linear correlations of the PRF coefficient were observed with increased agar. With silica concentrations, the negative linear correlation was strong. For all phantoms, calibrated PRF coefficients resulted in 1.01-3.01-fold higher temperature changes compared to the values calculated using a literature PRF coefficient.

Conclusions

Phantoms developed with a 6% w/v agar concentration and doped with 0%-8% w/v silica best resemble tissue PRF coefficients and should be preferred in HIFU studies. The estimated PRF coefficients can result in enhanced MR thermometry monitoring and evaluation of HIFU protocols.

Nanomaterial-Enabled Photothermal Heating and Its Use for Cancer Therapy via Localized Hyperthermia

Photothermal therapy (PTT), which employs nanoscale transducers delivered into a tumor to locally generate heat upon irradiation with near-infrared light, shows great potential in killing cancer cells through hyperthermia. The efficacy of such a treatment is determined by a number of factors, including the amount, distribution, and dissipation of the generated heat, as well as the type of cancer cell involved. The amount of heat generated is largely controlled by the number of transducers accumulated inside the tumor, the absorption coefficient and photothermal conversion efficiency of the transducer, and the irradiance of the light. The efficacy of treatment depends on the distribution of the transducers in the tumor and the penetration depth of the light. The vascularity and tissue thermal conduction both affect the dissipation of heat and thereby the distribution of temperature. The successful implementation of PTT in the clinic setting critically depends on techniques for real-time monitoring and management of temperature.

Technical Note: Advantages of a 2-Room Intraoperative 3-Tesla Magnetic Resonance Imaging Operating Suite for Performing Laser Interstitial Thermal Therapy in Pediatric Epilepsy and Tumor Surgery

OBJECTIVE

Magnetic resonance thermography-guided laser interstitial thermal therapy (LITT) provides a minimally invasive treatment option in children with central nervous system tumors or medically intractable epilepsy. However, transporting anesthetized children between an operating room (OR) and a radiologic suite creates logistical challenges. Thus we describe advantages of using a 2-room intraoperative magnetic resonance imaging (MRI) concept for LITT.

METHODS

Patients were pinned in a head frame that doubles as the lower part of the MRI head coil. Preoperative MRI was performed for accurate neuronavigation, after which laser fibers were stereotactically implanted. Transport between OR and MRI was achieved by sliding the top of the OR table onto a trolly.

RESULTS

We performed 12 procedures in 11 children, mean age 7.1 years (range: 2 to 14 years). Ten children suffered from medically intractable epilepsy, and 1 child had a pilocytic midbrain astrocytoma. Two fibers were placed in 8 and 1 fiber in 4 procedures. Mean entry point and target errors were 2.8 mm and 3.4 mm, respectively. Average transfer time from OR to MRI and vice versa was 9 minutes (±1 minute, 40 seconds). Altogether, 50% of the seizure patients were seizure free (Engel grade I) at 22 months' follow-up time. One hemorrhagic event, which could be managed nonoperatively, occurred. We recorded no surgical site or intracranial infections.

CONCLUSIONS

All LITT procedures were successfully carried out with head frame in the sterile environment. The intraoperative MRI suite proved to be advantageous for minimally invasive procedures, especially in young children resulting in short transports while maintaining high accuracy and safety.

Validation of a drift-corrected 3D MR temperature imaging sequence for breast MR-guided focused ultrasound treatments

Real-time temperature monitoring is critical to the success of thermally ablative therapies. This work validates a 3D thermometry sequence with k-space field drift correction designed for use in magnetic resonance-guided focused ultrasound treatments for breast cancer. Fiberoptic probes were embedded in tissue-mimicking phantoms, and temperature change measurements from the probes were compared with the magnetic resonance temperature imaging measurements following heating with focused ultrasound. Precision and accuracy of measurements were also evaluated in free-breathing healthy volunteers (N = 3) under a non-heating condition. MR temperature measurements agreed closely with those of fiberoptic probes, with a 95% confidence interval of measurement difference from -2.0 °C to 1.4 °C. Field drift-corrected measurements in vivo had a precision of 1.1 ± 0.7 °C and were accurate within 1.3 ± 0.9 °C across the three volunteers. The field drift correction method improved precision and accuracy by an average of 46 and 42%, respectively, when compared to the uncorrected data. This temperature imaging sequence can provide accurate measurements of temperature change in aqueous tissues in the breast and support the use of this sequence in clinical investigations of focused ultrasound treatments for breast cancer.

Validating a simulation model for laser-induced thermotherapy using MR thermometry

OBJECTIVES

We want to investigate whether temperature measurements obtained from MR thermometry are accurate and reliable enough to aid the development and validation of simulation models for Laser-induced interstitial thermotherapy (LITT).

METHODS

Laser-induced interstitial thermotherapy (LITT) is applied to ex-vivo porcine livers. An artificial blood vessel is used to study the cooling effect of large blood vessels in proximity to the ablation zone. The experimental setting is simulated using a model based on partial differential equations (PDEs) for temperature, radiation, and tissue damage. The simulated temperature distributions are compared to temperature data obtained from MR thermometry.

RESULTS

The overall agreement between measurement and simulation is good for two of our four test cases, while for the remaining cases drift problems with the thermometry data have been an issue. At higher temperatures local deviations between simulation and measurement occur in close proximity to the laser applicator and the vessel. This suggests that certain aspects of the model may need some refinement.

CONCLUSION

Thermometry data is well-suited for aiding the development of simulations models since it shows where refinements are necessary and enables the validation of such models.

MR relaxation properties of tissue-mimicking phantoms

High quality tissue-mimicking phantoms (TMPs) have a critical role in the preclinical testing of emerging modalities for diagnosis and therapy. TMPs capable of accurately mimicking real tissue in Magnetic Resonance guided Focused Ultrasound (MRgFUS) applications should be fabricated with precise T1 and T2 relaxation times. Given the current popularity of the MRgFUS technology, we herein performed a systematic review on the MR relaxation properties of different phantoms types. Polyacrylamide (PAA) and agar based phantoms were proven capable of accurately replicating critical thermal, acoustical, and MR relaxation properties of various body tissues. Although gelatin phantoms were also proven factional in this regard, they lack the capacity to withstand ablation temperatures, and thus, are only recommended for hyperthermia applications. Other gelling agents identified in the literature are Poly-vinyl alcohol (PVA), Polyvinyl Chloride (PVC), silicone, and TX-150/ TX-151; however, their efficacy in thermal studies is yet to be established. PAA gels are favorable in that they offer optical transparency enabling direct visualization of coagulative lesions. On the other hand, agar phantoms have lower preparation costs and were proven very promising for use with the MRgFUS technology, without the toxicity issues related to the preparation and storage of PAA materials. Remarkably, agar turned out to be the prominent modifier of the T2 relaxation time even for phantoms containing other types of gelling agents instead of agar. This review could be useful in manufacturing realistic MRgFUS phantoms while simultaneously indicating an opportunity for further research in the field with a particular focus on the MR behavior of agar-based TMPs.

Techniques for Temperature Monitoring of Myocardial Tissue Undergoing Radiofrequency Ablation Treatments: An Overview

Cardiac radiofrequency ablation (RFA) has received substantial attention for the treatment of multiple arrhythmias. In this scenario, there is an ever-growing demand for monitoring the temperature trend inside the tissue as it may allow an accurate control of the treatment effects, with a consequent improvement of the clinical outcomes. There are many methods for monitoring temperature in tissues undergoing RFA, which can be divided into invasive and non-invasive. This paper aims to provide an overview of the currently available techniques for temperature detection in this clinical scenario. Firstly, we describe the heat generation during RFA, then we report the principle of work of the most popular thermometric techniques and their features. Finally, we introduce their main applications in the field of cardiac RFA to explore the applicability in clinical settings of each method.

Fiber Bragg Grating Sensors for Performance Evaluation of Fast Magnetic Resonance Thermometry on Synthetic Phantom

The increasing recognition of minimally invasive thermal treatment of tumors motivate the development of accurate thermometry approaches for guaranteeing the therapeutic efficacy and safety. Magnetic Resonance Thermometry Imaging (MRTI) is nowadays considered the gold-standard in thermometry for tumor thermal therapy, and assessment of its performances is required for clinical applications. This study evaluates the accuracy of fast MRTI on a synthetic phantom, using dense ultra-short Fiber Bragg Grating (FBG) array, as a reference. Fast MRTI is achieved with a multi-slice gradient-echo echo-planar imaging (GRE-EPI) sequence, allowing monitoring the temperature increase induced with a 980 nm laser source. The temperature distributions measured with 1 mm-spatial resolution with both FBGs and MRTI were compared. The root mean squared error (RMSE) value obtained by comparing temperature profiles showed a maximum error of 1.2 °C. The Bland-Altman analysis revealed a mean of difference of 0.1 °C and limits of agreement 1.5/−1.3 °C. FBG sensors allowed to extensively assess the performances of the GRE-EPI sequence, in addition to the information on the MRTI precision estimated by considering the signal-to-noise ratio of the images (0.4 °C). Overall, the results obtained for the GRE-EPI fully satisfy the accuracy (~2 °C) required for proper temperature monitoring during thermal therapies.

Microfocusing sapphire capillary needle for laser surgery and therapy: Fabrication and characterization

A sapphire shaped capillary needle designed for collimating and focusing of laser radiation was proposed and fabricated by the edge-defined film-fed growth technique. It features an as-grown surface quality, high transparency for visible and near-infrared radiation, high thermal and chemical resistance and the complex shape of the tip, which protects silica fibers. The needle's geometrical parameters can be adjusted for use in various situations, such as type of tissue, modality of therapy and treatment protocol. The focusing effect was demonstrated numerically and observed experimentally during coagulation of the ex vivo porcine liver samples. This needle in combination with 0.22NA optical fiber allows intensive and uniform coagulation of 150 mm³ volume interstitially and 30 mm³ superficially by laser exposure with 280 J without tissue carbonization and fiber damaging along with delicate treatment of small areas. The demonstrated results reveal the perspectives of the proposed sapphire microfocusing needle for laser surgery and therapy.

Optimization of sapphire capillary needles for interstitial and percutaneous laser medicine

Sapphire capillary needles fabricated by edge-defined film-fed growth (EFG) technique hold strong potential in laser thermotherapy and photodynamic therapy, thanks to the advanced physical properties of sapphire. These needles feature an as-grown optical quality, their length is tens of centimeters, and they contain internal capillary channels, with open or closed ends. They can serve as optically transparent bearing elements with optical fibers introduced into their capillary channels in order to deliver laser radiation to biological tissues for therapeutic and, in some cases, diagnostic purposes. A potential advantage of the EFG-grown sapphire needles is associated with an ability to form the tip of a needle with complex geometry, either as-grown or mechanically treated, aimed at controlling the output radiation pattern. In order to examine a potential of the radiation pattern shaping, we present a set of fabricated sapphire needles with different tips. We studied the radiation patterns formed at the output of these needles using a He-Ne laser as a light source, and used intralipid-based tissue phantoms to proof the concept experimentally and the Monte-Carlo modeling to proof it numerically. The observed results demonstrate a good agreement between the numerical and experimental data and reveal an ability to control within wide limits the direction of tissue exposure to light and the amount of exposed tissue by managing the sapphire needle tip geometry.

A thermometry software tool for monitoring laser-induced interstitial thermotherapy

The purpose of this study was to develop a thermometry software tool for temperature monitoring during laser-induced interstitial thermotherapy (LITT). C++ programming language and several libraries including DICOM Toolkit, Grassroots DICOM library, Insight Segmentation and Registration Toolkit, Visualization Toolkit and Quasar Toolkit were used. The software's graphical user interface creates windows displaying the temperature map and the coagulation extent in the tissue, determined by the magnetic resonance imaging (MRI) thermometry with the echo planar imaging sequence and a numerical simulation based on the radiation and heat transfer in biological tissues, respectively. The software was evaluated applying the MRI-guided LITT to ex vivo pig liver and simultaneously measuring the temperature through a fiber-optic thermometer as reference. Using the software, the temperature distribution determined by the MRI method was compared with the coagulation extent simulation. An agreement was shown between the MRI temperature map and the simulated coagulation extent. Furthermore, the MRI-based and simulated temperatures agreed with the measured one - a correlation coefficient of 0.9993 and 0.9996 was obtained, respectively. The precision of the MRI temperature amounted to 2.4°C. In conclusion, the software tool developed in the present study can be applied for monitoring and controlling the LITT procedure in ex vivo tissues.

Advances in Magnetic Noble Metal/Iron-Based Oxide Hybrid Nanoparticles as Biomedical Devices

The study of the noble metal magnetic hybrid nanoparticles is a really promising topic from both the scientific and the technological points of views, with applications in several fields. Iron oxide materials which are hybridized with noble metal nanoparticles (NPs) have attracted increasing interest among researchers because of their cooperative effects on combined magnetic, electronic, photonic, and catalytic activities. This review article contains a summary of magnetic noble metal/iron oxide nanoparticle systems potentially useful in practical biomedical applications. Among the applications, engineered devices for both medical diagnosis and treatments were considered. The preparation to produce different structures, as blends or core-shell structures, of several nanometric systems was also considered. Several characterization techniques available to describe the structure, morphology and different kinds of properties of hybrid nanoparticles are also included in this review.

Predictive modeling of brain tumor laser ablation dynamics

INTRODUCTION

Laser interstitial thermal therapy (LITT) is a novel MR thermometry-guided thermoablative tool revolutionizing the clinical management of brain tumors. A limitation of LITT is our inability to estimate a priori how tissues will respond to thermal energy, which hinders treatment planning and delivery. The aim of this study was to determine whether brain tumor LITT ablation dynamics may be predicted by features of the preoperative MRI and the relevance of these data, if any, to the recurrence of metastases after LITT.

METHODS

Intraoperative thermal damage estimate (TDE) map pixels representative of irreversible damage were retrospectively quantified relative to ablation onset for 101 LITT procedures. Raw TDE pixel counts and TDE pixel counts modelled with first order dynamics were related to eleven independent variables derived from the preoperative MRI, demographics, laser settings, and tumor pathology. Stepwise regression analysis generated predictive models of LITT dynamics, and leave-one-out cross validation evaluated the accuracy of these models at predicting TDE pixel counts solely from the independent variables. Using a deformable atlas, TDE maps were co-registered to the immediate post-ablation MRI, allowing comparison of predicted and actual ablation sizes.

RESULTS

Brain tumor TDE pixel counts modelled with first order dynamics, but not raw pixel counts, are correlated with the independent variables. Independent variables showing strong relations to the TDE pixel measures include T1 gadolinium and T2 signal, perfusion, and laser power. Associations with tissue histopathology are minimal. Leave-one-out analysis demonstrates that predictive models using these independent variables account for 77% of the variance observed in TDE pixel counts. Analysis of metastases treated revealed a trend towards the over-estimation of LITT effects by TDE maps during rapid ablations, which was associated with tumor recurrence.

CONCLUSIONS

Features of the preoperative MRI are predictive of LITT ablation dynamics and could eventually be used to improve the clinical efficacy with which LITT is delivered to brain tumors.

Improved MR thermometry for laser interstitial thermotherapy

OBJECTIVES

To develop, test and evaluate improved 2D and 3D protocols for proton resonance frequency shift magnetic resonance temperature imaging (MRTI) of laser interstitial thermal therapy (LITT). The objective was to develop improved MRTI protocols in terms of temperature measurement precision and volume coverage compared to the 2D MRTI protocol currently used with a commercially available LITT system.

METHODS

Four different 2D protocols and four different 3D protocols were investigated. The 2D protocols used multi-echo readouts to prolong the total MR sampling time and hence the MRTI precision, without prolonging the total acquisition time. The 3D protocols provided volumetric thermometry by acquiring a slab of 12 contiguous slices in the same acquisition time as the 2D protocols. The study only considered readily available pulse sequences (Cartesian 2D and 3D gradient recalled echo and echo planar imaging [EPI]) and methods (partial Fourier and parallel imaging) to ensure wide availability and rapid clinical implementation across vendors and field strengths. In vivo volunteer studies were performed to investigate and compare MRTI precision and image quality. Phantom experiments with LITT heating were performed to investigate and compare MRTI precision and accuracy. Different coil setups were used in the in vivo studies to assess precision differences between using local (such as flex and head coils) and non-local (i.e., body coil) receive coils. Studies were performed at both 1.5 T and 3 T.

RESULTS

The improved 2D protocols provide up to a factor of two improvement in the MRTI precision in the same acquisition time, compared to the currently used clinical protocol. The 3D echo planar imaging protocols provide comparable precision as the currently used 2D clinical protocol, but over a substantially larger field of view, without increasing the acquisition time. As expected, local receive coils perform substantially better than the body coil, and 3 T provides better MRTI accuracy and precision than 1.5 T. 3D data can be zero-filled interpolated in all three dimensions (as opposed to just two dimensions for 2D data), reducing partial volume effects and measuring higher maximum temperature rises.

CONCLUSIONS

With the presented protocols substantially improved MRTI precision (for 2D imaging) or greatly improved field of view coverage (for 3D imaging) can be achieved in the same acquisition time as the currently used protocol. Only widely available pulse sequences and acquisition methods were investigated, which should ensure quick translation to the clinic. Lasers Surg. Med. 51:286-300, 2019. © 2019 Wiley Periodicals, Inc.

Quantitative MR thermometry based on phase-drift correction PRF shift method at 0.35 T

Background

Noninvasive magnetic resonance thermometry (MRT) at low-field using proton resonance frequency shift (PRFS) is a promising technique for monitoring ablation temperature, since low-field MR scanners with open-configuration are more suitable for interventional procedures than closed systems. In this study, phase-drift correction PRFS with first-order polynomial fitting method was proposed to investigate the feasibility and accuracy of quantitative MR thermography during hyperthermia procedures in a 0.35 T open MR scanner.

Methods

Unheated phantom and ex vivo porcine liver experiments were performed to evaluate the optimal polynomial order for phase-drift correction PRFS. The temperature estimation approach was tested in brain temperature experiments of three healthy volunteers at room temperature, and in ex vivo porcine liver microwave ablation experiments. The output power of the microwave generator was set at 40 W for 330 s. In the unheated experiments, the temperature root mean square error (RMSE) in the inner region of interest was calculated to assess the best-fitting order for polynomial fit. For ablation experiments, relative temperature difference profile measured by the phase-drift correction PRFS was compared with the temperature changes recorded by fiber optic temperature probe around the microwave ablation antenna within the target thermal region.

Results

The phase-drift correction PRFS using first-order polynomial fitting could achieve the smallest temperature RMSE in unheated phantom, ex vivo porcine liver and in vivo human brain experiments. In the ex vivo porcine liver microwave ablation procedure, the temperature error between MRT and fiber optic probe of all but six temperature points were less than 2 °C. Overall, the RMSE of all temperature points was 1.49 °C.

Conclusions

Both in vivo and ex vivo experiments showed that MR thermometry based on the phase-drift correction PRFS with first-order polynomial fitting could be applied to monitor temperature changes during microwave ablation in a low-field open-configuration whole-body MR scanner.

Tapered fiber optic applicator for laser ablation: Theoretical and experimental assessment of thermal effects on ex vivo model

Laser Ablation (LA) is a minimally invasive technique for tumor removal. The laser light is guided into the target tissue by a fiber optic applicator; thus the physical features of the applicator tip strongly influence size and shape of the tissue lesion. This study aims to verify the geometry of the lesion achieved by a tapered-tip applicator, and to investigate the percentage of thermally damaged cells induced by the tapered-tip fiber optic applicator. A theoretical model was implemented to simulate: i) the distribution of laser light fluence rate in the tissue through Monte Carlo method, ii) the induced temperature distribution, by means of the Bio Heat Equation, iii) the tissue injury, by Arrhenius integral. The results obtained by the implementation of the theoretical model were experimentally assessed. Ex vivo porcine liver underwent LA with tapered-tip applicator, at different laser settings (laser power of 1 W and 1.7 W, deposited energy equal to 330 J and 500 J, respectively). Almost spherical volume lesions were produced. The thermal damage was assessed by measuring the diameter of the circular-shaped lesion. The comparison between experimental results and theoretical prediction shows that the thermal damage discriminated by visual inspection always corresponds to a percentage of damaged cells of 96%. A tapered-tip applicator allows obtaining localized and reproducible damage close to spherical shape, whose diameter is related to the laser settings, and the simple theoretical model described is suitable to predict the effects, in terms of thermal damage, on ex vivo liver. Further trials should be addressed to adapt the model also on in vivo tissue, aiming to develop a tool useful to support the physician in clinical application of LA.

Validation of a mathematical model for laser-induced thermotherapy in liver tissue

The purpose of the study was to develop a simulation approach for laser-induced thermotherapy (LITT) that is based on mathematical models for radiation transport, heat transport, and tissue damage. The LITT ablation was applied to ex vivo pig liver tissue. Experiments were repeated with different laser powers, i.e., 22-34 W, and flow rates of the cooling water in the applicator system, i.e., 47-92 ml/min. During the procedure, the temperature was measured in the liver sample at different distances to the applicator as well as in the cooling circuit using a fiber optic thermometer. For validation, the simulation results were compared with the results of the laser ablation experiments in the ex vivo pig liver samples. The simulated and measured temperature curves presented a relatively good agreement. The Bland-Altman plot showed an average of temperature differences of -0.13 ^∘C and 95%-limits-of-agreement of ±7.11 ^∘C. The standard deviation amounted to ±3.63 ^∘C. The accuracy of the developed simulation is comparable with the accuracy of the MR thermometry reported in other clinical studies. The simulation showed a significant potential for the application in treatment planning.

Optothermal profile of an ablation catheter with integrated microcoil for MR-thermometry during Nd:YAG laser interstitial thermal therapies of the liver—an in-vitro experimental and theoretical study

PURPOSE

Flexible microcoils integrated with ablation catheters can improve the temperature accuracy during local MR-thermometry in Nd:YAG laser interstitial thermal therapies. Here, the authors are concerned with obtaining a preliminary confirmation of the clinical utility of the modified catheter. They investigate whether the thin-film substrate and copper tracks of the printed coil inductor affect the symmetry of the thermal profile, and hence of the lesion produced.

METHODS

Transmission spectroscopy in the near infrared was performed to test for the attenuation at 1064 nm through the 25 μm thick Kapton substrate of the microcoil. The radial transmission profile of an infrared high-power, light emitting diode with >80% normalized power at 1064 nm was measured through a cross section of the modified applicator to assess the impact of the copper inductor on the optical profile. The measurements were performed in air, as well as with the applicator surrounded by two types of scattering media; crystals of NaCl and a layer of liver-mimicking gel phantom. A numerical model based on Huygens-Fresnel principle and finite element simulations, using a commercially available package (COMSOL Multiphysics), were employed to compare with the optical measurements. The impact of the modified optical profile on the thermal symmetry was assessed by examining the high resolution microcoil derived thermal maps from a Nd:YAG laser ablation performed on a liver-mimicking gel phantom.

RESULTS

Less than 30% attenuation through the Kapton film was verified. Shadowing behind the copper tracks was observed in air and the measured radial irradiation correlated well with the diffraction pattern calculated numerically using the Huygens-Fresnel principle. Both optical experiments and simulations, demonstrate that shadowing is mitigated by the scattering properties of a turbid medium. The microcoil derived thermal maps at the end of a Nd:YAG laser ablation performed on a gel phantom in a 3 T scanner confirm that the modified irradiation pattern does not disrupt the thermal symmetry, even though, unlike tissue, the gel is minimally scattering.

CONCLUSIONS

The results from this initial assessment indicate that microcoils can be safely integrated with ablation catheters and ensure that the complete necrosis of the liver tumor can still be achieved.

The release of Doxorubicin from liposomes monitored by MRI and triggered by a combination of US stimuli led to a complete tumor regression in a breast cancer mouse model

The work aimed at developing a novel MRI-based theranostic protocol for improving the anticancer efficacy of a Doxil-like liposomal formulation. The goal was achieved stimulating the intratumor release of the drug from the nanocarrier and favoring its diffusion in the lesion by the sequential application of low-intensity pulsed ultrasound. The protocol was tested on mice bearing a syngeneic breast cancer model. The combination of acoustic waves with different characteristics allowed for: i) the release of the drug and the co-encapsulated MRI agent (Gadoteridol) from the liposomes in the vessels of the tumor region, and ii) the extravasation of the released material, as well as intact liposomes, in the tumor stroma. The MR-T1 contrast enhancement measured in the tumor reported on the delivery and US-triggered release of Doxorubicin. The developed protocol resulted in a marked increase in the intratumor drug concentration that, in turn, led to the complete regression of the lesion. The protocol has a good clinical translatability because all the components of the theranostic agent (Doxorubicin, liposomes, Gadoteridol) are approved for human use.

Effect of size, concentration, and type of spherical gold nanoparticles on heat evolution following laser irradiation using tissue-simulating phantoms

Photothermal therapy has recently gained a considerable attention particularly after the revolution of nanomaterials and nanotechnology. The aim of the present study is to assess the optimal photothermal response through investigating some effective parameters of spherical gold nanoparticles (AuNPs), e.g., type, size, and concentration, as a preclinical study for efficient photothermal treatment. Tissue-simulating phantoms based on agar and water media incorporated with two different types of AuNPs, spherical Au particles capped with citrate or spherical Au core-silica shell NPs, were built. Heat evolution for each NP type was recorded in the phantom matrix with different particle sizes at various concentrations following exposure to low laser power (irradiance 35 mW/cm(2)) and emitting at λ = 532 nm. Our results demonstrated that AuNPs capped with citrate recorded higher temperature elevations than those capped with silica shell. Particles with smaller sizes produced more heating effect than those having larger sizes. Also, higher temperatures were recorded at a critical concentration of NPs. Exponential decay constants based on theoretical calculations demonstrated that laser attenuation increases with the continuous increase of particle size and concentration.

Stereoelectroencephalography-guided radiofrequency thermocoagulation in the epileptogenic zone: a retrospective study on 89 cases

OBJECT

Radiofrequency thermocoagulation (RF-TC) of presumed epileptogenic lesions and/or structures has gained new popularity as a treatment option for drug-resistant focal epilepsy, mainly in patients with mesial temporal lobe epilepsy. The role of this minimally invasive procedure in more complex cases of drug-resistant epilepsy, which may require intracranial electroencephalographic evaluation, has not been fully assessed. This retrospective study reports on a case series of patients with particularly complex focal epilepsy who underwent stereoelectroencephalography (SEEG) evaluation with stereotactically implanted multicontact intracerebral electrodes for the detailed identification of the epileptogenic zone (EZ) and who received RF-TC in their supposed EZ (according to SEEG findings).

METHODS

Eighty-nine patients (49 male and 40 female; age range 2–49 years) who underwent SEEG evaluation and subsequent RF-TC of the presumed EZ at the authors' institution between January 2008 and December 2013 were selected. Brain MRI revealed structural abnormalities in 43 cases and no lesions in 46 cases. After SEEG, 67 patients were judged suitable for resective surgery (Group 1), whereas surgery was excluded for 22 patients (Group 2). Thermocoagulation was performed in each of these patients by using the previously implanted multicontact recording electrodes and delivering RF-generated currents to adjacent electrode contacts.

RESULTS

The mean number of TC sites per patient was 10.6 ± 7.2 (range 1–33). Sustained seizure freedom occurred after TC in 16 patients (18.0%) (13 in Group 1 and 3 in Group 2). A sustained worthwhile improvement was reported by 9 additional patients (10.1%) (3 in Group 1 and 6 in Group 2). As a whole, 25 patients (28.1%) exhibited a persistent significant improvement in their seizures. More favorable results were observed in patients with nodular heterotopy (p = 0.0001389), those with a lesion found on MRI (not significant), and those with hippocampal sclerosis (not significant). Other variables significantly correlated to seizure freedom were the patient's age (p = 0.02885) and number of intralesional TC sites (p = 0.0271). The patients in Group 1 who did not benefit at all (21 patients) or who experienced only a transient benefit (30 patients) from TC underwent microsurgical resection of their EZ. Thermocoagulation was followed by severe permanent neurological deficits in 2 patients (an unexpected complex neuropsychological syndrome in one patient and an expected and anticipated permanent motor deficit in the other).

CONCLUSIONS

This study provides evidence that SEEG-guided TC in the EZ may be a treatment option for particularly complex drug-resistant focal epilepsy that requires invasive evaluation. A small subset of patients who achieve seizure freedom or worthwhile improvement may avoid open surgery or take advantage of an otherwise unexpected treatment if resection is not an option. Patients with epileptogenic nodular heterotopy are probably ideal candidates for this treatment.

A Needlelike Probe for Temperature Monitoring During Laser Ablation Based on Fiber Bragg Grating: Manufacturing and Characterization

Temperature distribution monitoring in tissue undergoing laser ablation (LA) could be beneficial for improving treatment outcomes. Among several thermometric techniques employed in LA, fiber Bragg grating (FBG) sensors show valuable characteristics, although their sensitivity to strain entails measurement error for patient respiratory movements. Our work describes a solution to overcome this issue by housing an FBG in a surgical needle. The metrological properties of the probes were assessed in terms of thermal sensitivity (0.027 nm °C−1 versus 0.010 nm °C−1 for epoxy liquid encapsulated probe and thermal paste one, respectively) and response time (about 100 ms) and compared with properties of nonencapsulated FBG (sensitivity of 0.010 nm °C−1, response time of 43 ms). The error due to the strain caused by liver movements, simulating a typical respiratory pattern, was assessed: the strain induces a probes output error less than 0.5 °C, which is negligible when compared to the response of nonencapsulated FBG (2.5 °C). The metallic needle entails a measurement error, called artifact, due to direct absorption of the laser radiation. The analysis of the artifact was performed by employing the probes for temperature monitoring on liver undergoing LA. Experiments were performed at two laser powers (i.e., 2 W and 4 W) and at nine distances between the probes and the laser applicator. The artifact decreases with the distance and increases with the power: it exceeds 10 °C at 4 W, when the encapsulated probes are placed at 3.6 mm and 0 deg from the applicator, and it is lower than 1 °C for distance higher than 5 mm and angle higher than 30 deg.

Sonosensitive theranostic liposomes for preclinical in vivo MRI-guided visualization of doxorubicin release stimulated by pulsed low intensity non-focused ultrasound

The main goal of this study was to assess the theranostic performance of a nanomedicine able to generate MRI contrast as a response to the release from liposomes of the antitumor drug Doxorubicin triggered by the local exposure to pulsed low intensity non focused ultrasounds (pLINFU). In vitro experiments showed that Gadoteridol was an excellent imaging agent for probing the release of Doxorubicin following pLINFU stimulation. On this basis, the theranostic system was investigated in vivo on a syngeneic murine model of TS/A breast cancer. MRI offered an excellent guidance for monitoring the pLINFU-stimulated release of the drug. Moreover, it provided: i) an in vivo proof of the effective release of the liposomal content, and ii) a confirmation of the therapeutic benefits of the overall protocol. Ex vivo fluorescence microscopy indicated that the good therapeutic outcome was originated from a better diffusion of the drug in the tumor following the pLINFU stimulus. Very interestingly, the broad diffusion of the drug in the tumor stroma appeared to be mediated by the presence of the liposomes themselves. The results of this study highlighted either the great potential of US-based stimuli to safely trigger the release of a drug from its nanocarrier or the associated significant therapeutic improvement. Finally, MRI demonstrated to be a valuable technique to support chemotherapy and monitoring the outcome. Furthermore, in this specific case, the theranostic agent developed has a high clinical translatability because the MRI agent utilized is already approved for human use.