Optical coherence tomography to evaluate variance in the extent of carious lesions in depth

Diagnosis of dental caries based on attenuation coefficients analysis of optical coherence tomography images

Quantitative analysis of optical attenuation based on optical coherence tomography images will offer an effective method to enhance diagnostic capabilities. In this paper, the optical attenuation in demineralized caries specimens was calculated to distinguish between normal teeth and carious teeth and further to differentiate the severity of caries, and thus come to the half-automated diagnosis of dental caries. Results show that the attenuation coefficient in carious regions is approximately 4.97 mm - 1 ± 0.206 , while that of normal teeth is about 3.69 mm - 1 ± 0.231 . Attenuation coefficient of carious regions is 35% higher than that of normal teeth. Moreover, five classes of caries were qualified and classified based on the optical attenuation coefficient. Compared with the healthy teeth, there is a noticeable disparity in the attenuation coefficients of carious teeth, both on the surface and at the dentinoenamel junction. This study provides a method for accurate caries diagnosis, particularly in detection of early lesions and subtle structural changes.

Enamel Caries Lesion Depth Obtained by Optical Coherence Tomography and Transverse Microradiography: A Comparative Study

INTRODUCTION

Visual imaging of subsurface caries lesions is of vital interest in dentistry, which can be obtained by invasive radiography technique as well as by available non-destructive imaging approaches. Thus, as a first step toward the development of a new innovative approach, Spectral-domain optical coherence tomography (SD-OCT) was applied to detect the lesion depth in comparison to the established reference technique (transverse microradiography [TMR]).

METHODS

Bovine enamel specimens were demineralized for 5 days, following previous studies. For OCT, the resulting artificial lesions were scanned three-dimensionally (SD-OCT) and semi-automated measured (CarLQuant). For TMR, specimens were sectioned and the lesion depth was manually determined (Inspektor Research System).

RESULTS

The range of lesion depth detected with OCT was 24.0-174.0 μm (mouth rinse study), 18.0-178.0 μm (toothpastes study) and with TMR 59.2-198.0 μm (mouth rinse study), 33.2-133.4 μm (toothpastes study). We found a strong correlation between both methods in terms of lesion depth (Spearman rankwith outlierp < 0.001, Rho = 0.75, Spearman rankwithout outlierp = 0.001, Rho = 0.79). The two methods produce similar results (Passing-Bablok regression, 1.16). As deeper is the lesion, the smallest is the difference between both methods as indicated by Bland-Altman-plots.

CONCLUSION

Especially in the case of deep lesions, the values obtained by both methods are in agreement, and OCT can potentially substitute TMR to detect and assess lesion depth with the benefit of being non-destructive.

Assessibility of different CAD/CAM ceramics with optical coherence tomography

OBJECTIVES

To investigate the light penetration depth of various CAD/CAM ceramics and luting agents by spectral-domain optical coherence tomography (SD-OCT).

METHODS

Six CAD/CAM ceramics: lithium disilicate (LS2), zirconia-reinforced lithium silicate (ZLS), lithium aluminosilicate (LAS), polymer infiltrated (PIC), feldspar (FEL) and zirconium oxide (ZRO) and five common luting agents, two self-adhesive and three adhesive materials, were included. SD-OCT wavelengths (1310/1550 nm) and frequencies (5/28 kHz) that are particularly suitable for these materials were investigated. Subsequently, a clinical simulation was performed with an adhesively or self-adhesively inserted partial crown made of a ceramic that had an OCT penetration depth of > 1.0 mm.

RESULTS

Best SD-OCT penetration was obtained at 1550 nm and 28 kHz. For ZLS, LS2 and LAS, SD-OCT light penetration depth of > 4 mm was shown. In contrast, the penetration depth of ZRO, PIC and FEL was less than 1 mm. Adhesive and self-adhesive luting agents could be visualized up to ≥ 0.9 mm. All clinically relevant areas (ceramic restoration, luting area, interfaces and adjacent tooth structures) can be imaged when SD-OCT-suitable ceramics are used.

CONCLUSIONS

SD-OCT can be used to analyze CAD/CAM ceramics based on ZLS, LS2 and LAS, whereas ZRO, PIC, and FEL had insufficient penetration depth for clinical application. The type of luting agent or its thickness played an insignificant role. With suitable ceramics, SD-OCT can be recommended as a non-invasive examination tool.

CLINICAL SIGNIFICANCE

This study indicates that SD-OCT is a useful non-invasive examination method for monitoring lithium silicate-based ceramic restorations and adjacent structures.

Light-based diagnostic methods for the in vivo assessment of initial caries lesions: Laser fluorescence, QLF and OCT

OBJECTIVES

To evaluate different light-based caries diagnostic methods for assessment of non-cavitated initial carious lesions on smooth surfaces.

METHODS

39 participants were included. For each participant, three regions of interest (ROI) with ICDAS codes 0, 1 or 2 were defined. All ROIs (n = 117) were investigated/imaged with laser fluorescence (LF, DIAGNOdent 2095; KaVo dental GmbH), quantitative light-induced fluorescence (QLF; Biluminator 2+, Inspektor Research Systems B.V.) and spectral-domain optical coherence tomography (SD-OCT; Telesto II, Thorlabs GmbH). The values of LF, ΔF of QLF, and the lesion extent assessed by OCT were categorized. Frequency distribution of LF-/QLF- and OCT-scores was determined for each ICDAS code included. Inter- and intra-examiner reproducibility of QLF and OCT measurements were assessed by unweighted kappa coefficient (ĸ) and Wilcoxon test (α = 0.05).

RESULTS

Compared with LF and QLF, OCT showed various manifestations of carious lesions for visually sound ROIs and a larger variation of caries extent in depth within the same ICDAS code groups. Intra-examiner reproducibility ranged between 0.49 and 1.00 for the QLF analysis and between 0.95 and 0.99 for the OCT analysis. Inter-examiner reproducibility ranged between 0.17 and 0.32 for the QLF analysis and between 0.65 and 0.79 for the OCT analysis.

CONCLUSION

LF and QLF were insensitive to less pronounced smooth-surface lesions while OCT allowed differentiation based on the penetration depth of the carious lesions. This makes OCT a suitable method to complement conventional visual inspection in order to detect and assess (very) early lesions.

Transillumination and optical coherence tomography for the detection and diagnosis of enamel caries

BACKGROUND

Caries is one of the most prevalent and preventable conditions worldwide. If identified early enough then non-invasive techniques can be applied, and therefore this review focusses on early caries involving the enamel surface of the tooth. The cornerstone of caries detection and diagnosis is a visual and tactile dental examination, although alternative approaches are available. These include illumination-based devices that could potentially support the dental examination. There are three categories of illumination devices that exploit various methods of application and interpretation, each primarily defined by different wavelengths, optical coherence tomography (OCT), near-infrared (NIR), and fibre-optic technology, which incorporates more recently developed digital fibre optics (FOTI/DIFOTI).

OBJECTIVES

To estimate the diagnostic test accuracy of different illumination tests for the detection and diagnosis of enamel caries in children or adults. We also planned to explore the following potential sources of heterogeneity: in vitro or in vivo studies with different reference standards; tooth surface (occlusal, proximal, smooth surface, or adjacent to a restoration); single or multiple sites of assessment on a tooth surface; and the prevalence of caries into dentine.

SEARCH METHODS

Cochrane Oral Health's Information Specialist undertook a search of the following databases: MEDLINE Ovid (1946 to 15 February 2019); Embase Ovid (1980 to 15 February 2019); US National Institutes of Health Ongoing Trials Register (ClinicalTrials.gov, to 15 February 2019); and the World Health Organization International Clinical Trials Registry Platform (to 15 February 2019). We studied reference lists as well as published systematic review articles.

SELECTION CRITERIA

We included diagnostic accuracy study designs that compared the use of illumination-based devices with a reference standard (histology, enhanced visual examination with or without radiographs, or operative excavation). These included prospective studies that evaluated the diagnostic accuracy of a single index test and studies that directly compared two or more index tests. Both in vitro and in vivo studies of primary and permanent teeth were eligible for inclusion. We excluded studies that explicitly recruited participants with caries into dentine or frank cavitation. We also excluded studies that artificially created carious lesions and those that used an index test during the excavation of dental caries to ascertain the optimum depth of excavation.

DATA COLLECTION AND ANALYSIS

Two review authors extracted data independently and in duplicate using a standardised data extraction form and quality assessment based on QUADAS-2 specific to the clinical context. Estimates of diagnostic accuracy were determined using the bivariate hierarchical method to produce summary points of sensitivity and specificity with 95% confidence regions. The comparative accuracy of different illumination devices was conducted based on indirect and direct comparisons between methods. Potential sources of heterogeneity were pre-specified and explored visually and more formally through meta-regression.

MAIN RESULTS

We included 24 datasets from 23 studies that evaluated 16,702 tooth surfaces. NIR was evaluated in 6 datasets (673 tooth surfaces), OCT in 10 datasets (1171 tooth surfaces), and FOTI/DIFOTI in 8 datasets (14,858 tooth surfaces). The participant selection domain had the largest number of studies judged at high risk of bias (16 studies). Conversely, for the index test, reference standard, and flow and timing domains the majority of studies were judged to be at low risk of bias (16, 12, and 16 studies respectively). Concerns regarding the applicability of the evidence were judged as high or unclear for all domains. Notably, 14 studies were judged to be of high concern for participant selection, due to selective participant recruitment, a lack of independent examiners, and the use of an in vitro study design. The summary estimate across all the included illumination devices was sensitivity 0.75 (95% confidence interval (CI) 0.62 to 0.85) and specificity 0.87 (95% CI 0.82 to 0.92), with a diagnostic odds ratio of 21.52 (95% CI 10.89 to 42.48). In a cohort of 1000 tooth surfaces with a prevalence of enamel caries of 57%, this would result in 142 tooth surfaces being classified as disease free when enamel caries was truly present (false negatives), and 56 tooth surfaces being classified as diseased in the absence of enamel caries (false positives). A formal comparison of the accuracy according to device type indicated a difference in sensitivity and/or specificity (Chi2(4) = 34.17, P < 0.01). Further analysis indicated a difference in the sensitivity of the different devices (Chi2(2) = 31.24, P < 0.01) with a higher sensitivity of 0.94 (95% CI 0.88 to 0.97) for OCT compared to NIR 0.58 (95% CI 0.46 to 0.68) and FOTI/DIFOTI 0.47 (95% CI 0.35 to 0.59), but no meaningful difference in specificity (Chi2(2) = 3.47, P = 0.18). In light of these results, we planned to formally assess potential sources of heterogeneity according to device type, but due to the limited number of studies for each device type we were unable to do so. For interpretation, we presented the coupled forest plots for each device type according to the potential source of heterogeneity. We rated the certainty of the evidence as low and downgraded two levels in total due to avoidable and unavoidable study limitations in the design and conduct of studies, indirectness arising from the in vitro studies, and imprecision of the estimates.

AUTHORS' CONCLUSIONS

Of the devices evaluated, OCT appears to show the most potential, with superior sensitivity to NIR and fibre-optic devices. Its benefit lies as an add-on tool to support the conventional oral examination to confirm borderline cases in cases of clinical uncertainty. OCT is not currently available to the general dental practitioner, and so further research and development are necessary. FOTI and NIR are more readily available and easy to use; however, they show limitations in their ability to detect enamel caries but may be considered successful in the identification of sound teeth. Future studies should strive to avoid research waste by ensuring that recruitment is conducted in such a way as to minimise selection bias and that studies are clearly and comprehensively reported. In terms of applicability, any future studies should be undertaken in a clinical setting that is reflective of the complexities encountered in caries assessment within the oral cavity.

An Intraoral OCT Probe to Enhanced Detection of Approximal Carious Lesions and Assessment of Restorations

Caries, the world's most common chronic disease, remains a major cause of invasive restorative dental treatment. To take advantage of the diagnostic potential of optical coherence tomography (OCT) in contemporary dental prevention and treatment, an intraorally applicable spectral-domain OCT probe has been developed based on an OCT hand-held scanner equipped with a rigid 90°-optics endoscope. The probe was verified in vitro. In vivo, all tooth surfaces could be imaged with the OCT probe, except the vestibular surfaces of third molars and the proximal surface sections of molars within a "blind spot" at a distance greater than 2.5 mm from the tooth surface. Proximal surfaces of 64 posterior teeth of four volunteers were assessed by intraoral OCT, visual-tactile inspection, bitewing radiography and fiber-optic transillumination. The agreement in detecting healthy and carious surfaces varied greatly between OCT and established methods (18.2-94.7%), whereby the established methods could always be supplemented by OCT. Direct and indirect composite and ceramic restorations with inherent imperfections and failures of the tooth-restoration bond were imaged and qualitatively evaluated. The intraoral OCT probe proved to be a powerful technological approach for the non-invasive imaging of healthy and carious hard tooth tissues and gingiva as well as tooth-colored restorations.

3D imaging of proximal caries in posterior teeth using optical coherence tomography

Optical coherence tomography (OCT) can create cross-sectional images of tooth without X-ray exposure. This study aimed to investigate the diagnostic accuracy of 3D imaging of OCT for proximal caries in posterior teeth. Thirty-six human molar teeth with 51 proximal surfaces visibly 6 intact, 16 slightly demineralized, and 29 distinct carious changes were mounted to take digital radiographs and 3D OCT images. The sensitivity, specificity and area under the receiver operating characteristic curve (AUC) for the diagnosis of enamel caries and dentin caries were calculated to quantify the diagnostic ability of 3D OCT in comparison with digital radiography. Diagnostic accuracy was evaluated by the agreement with histology using weighted Kappa. OCT showed significantly higher sensitivity, AUC and Kappa values than radiography. OCT can be a safer option for the diagnosis of proximal caries in posterior teeth that can be applied to the patients without X-ray exposure.

Effects of artificial aging and progression of cracks on thin occlusal veneers using SD-OCT

OBJECTIVES

The purpose of this study was to evaluate the effects of artificial aging on thin glass-ceramic occlusal premolar veneers, adhesively bonded to dentin, by examining the changes caused by artificial aging using spectral domain optical coherence tomography (SD-OCT). In addition, the development of cracks in the ceramic veneers and their possible influence on the behavior of the ceramic restorations were examined.

METHODS

In total, 48 extracted sound upper premolars were prepared in the dentin for occlusal veneers milled from lithium disilicate ceramic blocks (IPS e.max CAD, Ivoclar Vivadent, Liechtenstein). All restorations were adhesively bonded using resin cement (Variolink Esthetic DC, Ivoclar Vivadent). Specimens were 3-dimensionally and 2-dimensionally imaged by SD-OCT (Telesto II, Thorlabs GmbH, Germany), then subjected to thermal-dynamic loading in a chewing simulator with 1,200,000 cycles at a load of 10 kg. Specimens were 2D and 3D imaged again after the artificial aging. Finally, they were subjected to quasi-static loading using a universal testing machine until failure occurred and later examined microscopically to assess the mode of failure. ANOVA test was performed for statistical analysis of data and Tukey's post-hoc test was used to compare the groups at 5% significance level. Chi-Square Test and Fischer's Exact Test of Independence were conducted to test the association between nominal variables.

RESULTS

No changes or irregularities were observed in the cement layer or tooth substrate after the aging process. However, wear of the ceramic was noticed at the surface of contact with the antagonist during the test. The development of cracks was detected in 23% of the specimens. Cracks did not affect the fracture strength (p > 0.05) but influenced the mode of failure (p ≤ 0.001).

SIGNIFICANCE

Optical coherence tomography allows an easy and non-invasive method to internally scan teeth and restorations. Development of cracks in the ceramic did not affect the fracture strength of the restorations but might lead to a more catastrophic type of failure.