Monomer reactivity ratio and thermal performance of α-methyl styrene and glycidyl methacrylate copolymers

Effect of Different Comonomers Added to Graft Copolymers on the Properties of PLA/PPC/PLA-g-GMA Blends

The melt-free radical grafting of glycidyl methacrylate (GMA) onto poly (lactic acid) (PLA) with styrene (St), α-methylstyrene (AMS), and epoxy resin (EP) as comonomers in a twin-screw extruder was used to prepare PLA-g-GMA graft copolymers. The prepared graft copolymers were then used as compatibilizers to prepare PLA/PPC/PLA-g-GMA blends by melt blending with PLA and polypropylene carbonate (PPC), respectively. The effects of different comonomers in the PLA-g-GMA graft copolymers on the thermal, rheological, optical, and mechanical properties and microstructure of the blends were studied. It was found that the grafting degree of PLA-g-GMA graft copolymers was increased to varying degrees after the introduction of comonomers in the PLA-g-GMA grafting reaction system. When St was used as the comonomer, the grafting degree of the PLA-g-GMA graft copolymer increased most significantly, from 0.8 to 1.6 phr. St as a comonomer also most improved the compatibility between PLA and PPC, and the haze of the blends was reduced while maintaining high transmittance. In addition, the PLA-g-GMA graft copolymer with the introduction of St as a comonomer significantly improved the impact toughness of the blends, while the thermal stability and tensile strength of the blends remained largely unchanged.

Physicochemical properties of dimethacrylate resin composites with comonomer of Hexa/Tri-ethylene glycol bis(carbamate-isoproply-α-methylstyrene)

New photocurable "Phene" like monomers Hexaethylene glycol bis(carbamate-isoproply-α-methylstyrene) (HE-Phene) and Triethylene glycol bis(carbamate-isoproply-α-methylstyrene) (TE-Phene) were synthesized and incorporated into Bis-GMA/TEGDMA with the aim of reducing polymerization shrinkage without detriment to the physical and handling properties of the resin composites. Phene like monomers (HE/TE-Phene) were synthesized through a one-step reaction route, and their structures were confirmed by FT-IR and ¹H-NMR spectra. HE/TE-Phene were incorporated into Bis-GMA/TEGDMA (50/50,wt/wt) with a series of mass fraction (from 0 wt.% to 40 wt.%). Experimental resin composites were prepared by mixing 29 wt.% of resin matrix to 71 wt.% of particulate-fillers. Degree of conversion (DC) was determined by FT-IR analysis. The volumetric shrinkage (VS) was calculated as a buoyancy change in distilled water by means of the Archimedes principle. Polymerization shrinkage-stress (SS) was measured using the tensilometer technique. The flexural strength (FS), modulus (FM), and fracture toughness (FT) were measured using a three-point bending setup. Viscosity was analyzed with a rotating disk rheometer. Water sorption and solubility were also measured. ANOVA analysis showed that DC (after 40 s), VS, and SS were in a trend of decreasing with the increasing of HE/TE-Phene concentration. In general, the experimental resin composites had comparable FT, FS and FM (p > 0.05) when the mass fraction of HE/TE-Phene in resin matrix was not more than 30 wt.%. The overall tested properties prove that including HE/TE-Phene up to 30 wt.% into Bis-GMA/TEGDMA resin could be potentially useful in the formulation of low-shrinkage resin composites.

Preparation of antibacterial and radio-opaque dental resin with new polymerizable quaternary ammonium monomer

OBJECTIVE

A new polymerizable quaternary ammonium monomer (IPhene) with iodine anion was synthesized and incorporated into Bis-GMA/TEGDMA (50/50, wt/wt) to prepare antibacterial and radio-opaque dental resin.

METHODS

IPhene was synthesized through a 2-steps reaction route, and its structure was confirmed by FT-IR and (1)H-NMR spectra. IPhene was incorporated into Bis-GMA/TEGDMA (50/50, wt/wt) with a series of mass fraction (from 10 wt.% to 40 wt.%). Degree of monomer conversion (DC) was determined by FT-IR analysis. Polymerization shrinkage was determined according to the variation of density before and after polymerization. The flexural strength, modulus of elasticity, and fracture energy were measured using a three-point bending set up. Radiograph was taken to evaluate the radio-opacity of the polymer. A single-species biofilm model with Streptococcus mutans (S. mutans) as the tests organism was used to evaluate the antibacterial activity of the polymer. Bis-GMA/TEGDMA resin system without IPhene was used as a control group.

RESULTS

FT-IR and (1)H-NMR spectra of IPhene revealed that IPhene was the same as the designed structure. ANOVA analysis showed that when mass fraction of IPhene was more than 10 wt.%, the obtained resin formulation had lower DC, polymerization shrinkage, FS, and FM than control resin (p<0.05). Polymers with 20 wt.% and 30 wt.% IPhene had higher fracture energies than control polymer (p<0.05). IPhene containing samples had higher radio-opacity than control group (p<0.05), and radio-opacity of IPhene containing sample increased with the increasing of IPhene mass fraction (p<0.05). Only polymers with 30 wt.% and 40 wt.% of IPhene showed antibacterial activity (p<0.05).

SIGNIFICANCE

IPhene could endow dental resin with both antibacterial and radio-opaque activity when IPhene reached 30 wt.% or more. Though sample with 30 wt.% of IPhene had lower FS and FM than control group, its lower volumetric shrinkage, higher fracture energy, higher radio-opacity, and antibacterial activity still made it having potential to be used in dentistry.