Constitutive modeling of menisci tissue: a critical review of analytical and numerical approaches

Effect of meniscus modelling assumptions in a static tibiofemoral finite element model: importance of geometry over material

Finite element studies of the tibiofemoral joint have increased use in research, with attention often placed on the material models. Few studies assess the effect of meniscus modelling assumptions in image-based models on contact mechanics outcomes. This work aimed to assess the effect of modelling assumptions of the meniscus on knee contact mechanics and meniscus kinematics. A sensitivity analysis was performed using three specimen-specific tibiofemoral models and one generic knee model. The assumptions in representing the meniscus attachment on the tibia (shape of the roots and position of the attachment), the material properties of the meniscus, the shape of the meniscus and the alignment of the joint were evaluated, creating 40 model instances. The values of material parameters for the meniscus and the position of the root attachment had a small influence on the total contact area but not on the meniscus displacement or the force balance between condyles. Using 3D shapes to represent the roots instead of springs had a large influence in meniscus displacement but not in knee contact area. Changes in meniscus shape and in knee alignment had a significantly larger influence on all outcomes of interest, with differences two to six times larger than those due to material properties. The sensitivity study demonstrated the importance of meniscus shape and knee alignment on meniscus kinematics and knee contact mechanics, both being more important than the material properties or the position of the roots. It also showed that differences between knees were large, suggesting that clinical interpretations of modelling studies using single geometries should be avoided.

Fractional-order poromechanics for a fully saturated biological tissue: Biomechanics of meniscus

Biomechanics of biological fibrous tissues as the meniscus are strongly influenced by past histories of strains involving the so-called material hereditariness. In this paper, a three-axial model of linear hereditariness that makes use of fractional-order calculus is used to describe the constitutive behavior of the tissue. Fluid flow across meniscus' pores is modeled in this paper with Darcy relation yielding a novel model of fractional-order poromechanics, describing the evolution of the diffusion phenomenon in the meniscus. A numerical application involving an 1D confined compression test is reported to show the effect of the material hereditariness on the pressure drop evolution.

Region- and layer-specific investigations of the human menisci using SHG imaging and biaxial testing

In this paper, we examine the region- and layer-specific collagen fiber morphology via second harmonic generation (SHG) in combination with planar biaxial tension testing to suggest a structure-based constitutive model for the human meniscal tissue. Five lateral and four medial menisci were utilized, with samples excised across the thickness from the anterior, mid-body, and posterior regions of each meniscus. An optical clearing protocol enhanced the scan depth. SHG imaging revealed that the top samples consisted of randomly oriented fibers with a mean fiber orientation of 43.3 ^o . The bottom samples were dominated by circumferentially organized fibers, with a mean orientation of 9.5 ^o . Biaxial testing revealed a clear anisotropic response, with the circumferential direction being stiffer than the radial direction. The bottom samples from the anterior region of the medial menisci exhibited higher circumferential elastic modulus with a mean value of 21 MPa. The data from the two testing protocols were combined to characterize the tissue with an anisotropic hyperelastic material model based on the generalized structure tensor approach. The model showed good agreement in representing the material anisotropy with a mean r ² = 0.92.

Influence of material heterogeneity on the mechanical response of articulated cartilages in a knee joint

Structurally, the articular cartilages are heterogeneous owing to nonuniform distribution and orientation of its constituents. The oversimplification of this soft tissue as a homogeneous material is generally considered in the simulation domain to estimate contact pressure along with other physical responses. Hence, there is a need for investigating knee cartilages for their actual response to external stimuli. In this article, impact of material and geometrical heterogeneity of the cartilage is resolved using well known material models. The findings are compared with conventional homogeneous models. The results indicate vital differences in contact pressure distribution and tissue deformation. Further, this study paves way for standardizing material models to extract maximum information possible for investigating knee mechanics with variable geometry and case specific parameters.

Experiments and hyperelastic modeling of porcine meniscus show heterogeneity at high strains

Constitutive modeling of the meniscus is critical in areas like knee surgery and tissue engineering. At low strain rates, the meniscus can be described using a hyperelastic model. Calibration of hyperelastic material models of the meniscus is challenging on many fronts due to material variability and friction. In this study, we present a framework to determine the hyperelastic material parameters of porcine meniscus (and similar soft tissues) using no-slip uniaxial compression experiments. Because of the nonhomogeneous deformation in the specimens, a finite element solution is required at each step of the iterative calibration process. We employ a Bayesian calibration approach to account for the inherent material variability and a Bayesian optimization approach to minimize the resulting cost function in the material parameter space. Cylindrical specimens of porcine meniscus from the anterior, middle and posterior regions are tested up to 30% compressive strain and the Yeoh form of hyperelastic strain energy density function is used to describe the material response. The results show that the Yeoh form is able to accurately describe the compressive response of porcine meniscus and that the Bayesian calibration and optimization approaches are able to calibrate the model in a computationally efficient manner while taking into account the inherent material variability. The results also show that the shear modulus or the initial stiffness is roughly uniform across the different areas of the meniscus, but there is significant spatial heterogeneity in the response at high strains. In particular, the middle region is considerably stiffer at high strains. This heterogeneity is important to consider in modeling the response of the meniscus for clinical applications.

Numerical Modeling of Shockwave Treatment of Knee Joint

Arthritis is a degenerative disease that primarily affects the cartilage and meniscus of the knee joint. External acoustic stimulation is used to treat this disease. This article presents a numerical model of the knee joint aimed at the computer-aided study of the regenerative effects of shockwave treatment. The presented model was verified and validated. A numerical analysis of the conditions for the regeneration of the tissues of the knee joint under shockwave action was conducted. The results allow us to conclude that to obtain the conditions required for the regeneration of cartilage tissues and meniscus (compressive stresses above the threshold value of 0.15 MPa to start the process of chondrogenesis; distortional strains above the threshold value of 0.05% characterized by the beginning of the differentiation of the tissues in large volumes; fluid pressure corresponding to the optimal level of 68 kPa to transfer tissue cells in large volumes), the energy flux density of therapeutic shockwave loading should exceed 0.3 mJ/mm².