Glass coatings to enhance the interfacial bond strength between veneering ceramic and zirconia

Effect of different interfacial surface treatments on the shear bond strength of veneering ceramic and zirconia core

BACKGROUND

Several interfacial surface treatments of zirconia surfaces have been proposed to improve adhesion to ceramic veneering. However, information regarding the durability and effect of such treatments on the bond strength following such treatments is lacking.

AIM OF THE STUDY

This study aimed to evaluate the shear bond strength between veneering ceramic and zirconia core after different interfacial surface treatments.

MATERIALS AND METHODS

Fifty-two discs (8 mm in diameter and 3 mm in height) were fabricated from zirconia blanks using a microtome cutting machine. Zirconia discs were divided into four groups (n = 13). Group I was subjected to air-borne abrasion using (Al₂O₃), group II was coated by bioglass, group III was coated with ZirLiner, and group IV was subjected to wash firing (sprinkle technique). A cylinder (4 mm in diameter and 3 mm in height) of veneering ceramic was fired on top of the zirconia core. Shear bond strength (SBS) between zirconia core and veneering ceramic was evaluated by using a universal testing machine. The data was collected and statistically analysed using One-Way ANOVA followed by multiple pairwise comparisons using Bonferroni adjusted significance level. The failure modes were assessed using a stereomicroscope for each group.

RESULTS

The highest mean bond strength was recorded in group III (17.98 ± 2.51 MPa), followed by group II (15.10 ± 4.53 MPa), then group I 14.65 ± 2.97 MPa. The lowest mean bond strength was recorded in group IV (13.28 ± 3.55 MPa).

CONCLUSIONS

Surface treatments had an effect on the zirconia-veneer shear bond strength. Liner coating revealed the highest shear bond strength values, significantly higher in comparison to wash firing (sprinkle technique) .

Construction of Nanostructured Glass-Zirconia to Improve the Interface Stability of Dental Bilayer Zirconia

Bilayer zirconia restoration is one of the most commonly used restorations in dental practice, but the high frequency of the cohesive/adhesive fracture of veneered porcelain is still a problem. This paper focuses on the development of nanostructured glass-zirconia to improve the interface stability of dental zirconia substrate and veneered porcelain. A novel SiO₂-Li₂O-Al₂O₃ (SLA) glass was prepared and infiltrated into the surface of fully sintered dental zirconia to obtain nanostructured glass-zirconia structure. The prepared glass-zirconia was analyzed with scanning electron microscopes (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction spectroscopy (XRD). The wettability, roughness and 3D morphology of zirconia were altered, and shear bonding strength (SBS) test demonstrated almost double increase in SBS values of the nanostructured glass-zirconia structure. The failure modes and microstructure characteristics also verified the improved interfacial stability. This investigation provides a promising method for enhancing the structural stability of bilayer zirconia restorations.

Effect of different zirconia surface pretreatments on the flexural strength of veneered Y-TZP ceramic before and after in vitro aging

PURPOSE

The investigation of zirconia core surface pretreatments on the flexural strength of bilayered zirconia ceramics before and after artificial accelerating aging.

METHODS

Ninety bar-shaped specimens were manufactured from Yttria Stabilized Tetragonal Zirconia Polycrystal (Y-TZP) and divided in three groups depending on zirconia surface pretreatment before veneering: layering with liner, pretreatment with silane-containing gas flame (SGF) with the Silano-Pen device and alumina air-abrasion. Half of the veneered specimens in each group (n=15) underwent artificial accelerating aging. A 4-point bending test was performed to determine flexural strength. Three specimens from each group were further analyzed using Scanning Electron Microscopy (SEM), X-ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FTIR) before veneering and after fracture (aged and non-aged subgroups).

RESULTS

Alumina air-abrasion was correlated to increased phase transformation from tetragonal to monoclinic zirconia phase. Qualitative analysis revealed that with the majority of the specimens pretreated with the silane-containing gas flame, areas of the veneering material remained firmly attached to the zirconia core after flexural strength testing. There was no statistically significant difference on the flexural strength among the groups before or after aging. Artificial accelerating aging resulted in statistically significant higher flexural strength of the specimens after aging.

CONCLUSION

SGF pretreatment can be an acceptable and feasible alternative method before the veneering of Y-TZP zirconia as it presented slightly higher bond strength compared with alumina air-abrasion which was associated with higher tetragonal to monoclinic (t→m) phase transformation. Accelerating aging leads to an increase of the mechanical properties under in vitro conditions.

Analysis of surface conditioning methods on core-veneer bond strength of CAD/CAM zirconia restorations

BACKGROUND

The increased strength of zirconia has resulted in its widespread application in clinical dentistry. Nevertheless, the fracture of veneering porcelains remains one of the key reasons of failure.

OBJECTIVE

The objective of this study was to compare and analyze the influence of surface conditioning methods on the core-veneer bond strength of zirconia restorations.

METHODS

Thirty specimens of zirconia core with sizes 10 × 5 × 5 mm were layered with porcelain of sizes 5 × 3 × 3 mm. On the basis of different surface conditioning methods, four groups were made: Group I: abrasion with airborne alumina particles of 110 μm size, Group II: sandblasting with silica coated alumina particles of 50 μm in size, Group III (modified group): alteration with a coating of zirconia powder prior to sintering, and Group IV (control group): metal core specimens. The shear force of all specimens was tested using a universal testing machine with a 0.5 mm/min crosshead speed. One-way analysis of variance (ANOVA) and Tukey's post hoc pair wise comparison (p= 0.05) were performed to analyze the shear bond strength. A scanning electron microscope was used to assess the fractured specimens.

RESULTS

A statistically significant difference was noted between the groups. The mean value of shear bond strength was 40.25 MPa for Group I, 41.93 MPa for Group II, 48.08 MPa for Group III and 47.01 MPa for Group IV.

CONCLUSIONS

The modified zirconia group and control group demonstrated a significantly higher mean bond strength than that of Group I, where airborne particle abrasion was used. The scanning electron microscope showed that cohesive fracture in the porcelain veneers was the main problem of failure in altered zirconia. The modified zirconia specimens in Group III demonstrated significantly improved values of shear bond strength.

Antibacterial Bio-Based Polymers for Cranio-Maxillofacial Regeneration Applications

Cranio-maxillofacial structure is a region of particular interest in the field of regenerative medicine due to both its anatomical complexity and the numerous abnormalities affecting this area. However, this anatomical complexity is what makes possible the coexistence of different microbial ecosystems in the oral cavity and the maxillofacial region, contributing to the increased risk of bacterial infections. In this regard, different materials have been used for their application in this field. These materials can be obtained from natural and renewable feedstocks, or by synthetic routes with desired mechanical properties, biocompatibility and antimicrobial activity. Hence, in this review, we have focused on bio-based polymers which, by their own nature, by chemical modifications of their structure, or by their combination with other elements, provide a useful antibacterial activity as well as the suitable conditions for cranio-maxillofacial tissue regeneration. This approach has not been reviewed previously, and we have specifically arranged the content of this article according to the resulting material and its corresponding application; we review guided bone regeneration membranes, bone cements and devices and scaffolds for both soft and hard maxillofacial tissue regeneration, including hybrid scaffolds, dental implants, hydrogels and composites.