Comparison of the efficiency of bacterial and fungal laccases in delignification and detoxification of steam-pretreated lignocellulosic biomass for bioethanol production

Effect of Laccase Detoxification on Bioethanol Production from Liquid Fraction of Steam-Pretreated Olive Tree Pruning

During lignocellulosic bioethanol production, the whole slurry obtained by steam explosion is filtered, generating a water-insoluble fraction rich in cellulose which is used for saccharification and ethanol fermentation, as well as a liquid fraction containing solubilised glucose and xylose but also some inhibitory by-products (furan derivatives, weak acids and phenols), which limits its use for this purpose. Since utilization of this liquid fraction to ethanol is essential for an economically feasible cellulosic ethanol process, this work studied a laccase from Myceliophthora thermophila to detoxify the liquid fraction obtained from steam-pretreated olive tree pruning (OTP) and to overcome the effects of these inhibitors. Then, the fermentation of laccase-treated liquid fraction was evaluated on ethanol production by different Saccharomyces cerevisiae strains, including the Ethanol Red, with the capacity to ferment glucose but not xylose, and the xylose-fermenting recombinant strain F12. Laccase treatment reduced total phenols content by 87% from OTP liquid fraction, not affecting furan derivatives and weak acids concentration. Consequently, the fermentative behavior of both Ethanol Red and F12 strains was improved, and ethanol production and yields were increased. Moreover, F12 strain was capable of utilizing some xylose, which increased ethanol production (10.1 g/L) compared to Ethanol Red strain (8.6 g/L).

NMR Study on Laccase Polymerization of Kraft Lignin Using Different Enzymes Source

The usage of laccases is a sustainable and environmentally friendly approach to modifying the Kraft lignin structure for use in certain applications. However, the inherent structure of Kraft lignin, as well as that resulting from laccase modification, still presents challenges for fundamental comprehension and successful lignin valorization. In this study, bacterial and fungal laccases were employed to modify eucalypt Kraft lignin. To evaluate the type and range of the chemical and structural changes of laccase-treated lignins, different NMR techniques, including solution ¹H and 2D NMR (heteronuclear single quantum correlation (HSQC)), and solid-state ¹³C NMR, were applied. Size exclusion chromatography and infrared spectroscopy were also used. Interestingly, HSQC analysis showed substantial changes in the oxygenated aliphatic region of lignins, showing an almost complete absence of signals corresponding to side-chains due to laccase depolymerization. Simultaneously, a significant loss of aromatic signals was observed by HSQC and ¹H NMR, which was attributed to a deprotonation of the lignin benzenic rings due to polymerization/condensation by laccase reactions. Then, condensed structures, such as α-5', 5-5', and 4-O-5', were detected by HSQC and ¹³C NMR, supporting the increment in molecular weight, as well as the phenolic content reduction determined in lignins.

Enzyme-Catalyzed Polymerization of Kraft Lignin from Eucalyptus globulus: Comparison of Bacterial and Fungal Laccases Efficacy

Kraft lignin, a side-stream from the pulp and paper industry, can be modified by laccases for the synthesis of high added-value products. This work aims to study different laccase sources, including a bacterial laccase from Streptomyces ipomoeae (SiLA) and a fungal laccase from Myceliophthora thermophila (MtL), for kraft lignin polymerization. To study the influence of some variables in these processes, a central composite design (CCD) with two continuous variables (enzyme concentration and reaction time) and three levels for each variable was used. The prediction of the behavior of the output variables (phenolic content and molecular weight of lignins) were modelled by means of response surface methodology (RSM). Moreover, characterization of lignins was performed by Fourier-transform infrared (FTIR) spectroscopy and different nuclear magnetic resonance (NMR) spectroscopy techniques. In addition, antioxidant activity was also analyzed. Results showed that lignin polymerization (referring to polymerization as lower phenolic content and higher molecular weight) occurred by the action of both laccases. The enzyme concentration was the most influential variable in the lignin polymerization reaction within the range studied for SiLA laccase, while the most influential variable for MtL laccase was the reaction time. FTIR and NMR characterization analysis corroborated lignin polymerization results obtained from the RSM.

Nepenthes mirabilis Fractionated Pitcher Fluid Use for Mixed Agro-Waste Pretreatment: Advocacy for Non-Chemical Use in Biorefineries

This study determined whether it is feasible to pretreat mixed agro-waste of different particle sizes using the pitcher fluid of Nepenthes mirabilis (N. mirabilis), which is known to digest leaf litter due to the enzyme cocktail contained in the fluid. This is due to the need for the holocellulolysis (a source of fermentable sugars) of mixed agro-waste to produce fermentable hydrolysates. The pitcher fluid was fractionated (<3 kDa, ˃3 kDa, <10 kDa, ˃10 kDa) and slurrified with the mixed agro-waste, i.e., 25% (w/w) for each waste—orange peels, apple peels, maize cobs, grape pomace, and oak plant leaf litter of various particle sizes, i.e., >75 µm x < 106 µm and >106 µm. The process of producing a high concentration of total reducible sugars (TRSs) with the lowest production of total phenolic compounds (TPCs) was determined to be a particle size of >106 µm, pretreatment for 72 h, and an enzyme fraction of <10 kDa, whereby 97 g/L of TRSs were produced with a significantly lower TPCs load (1 g/L). Furthermore, the <10 kDa showed preferable physico-chemical properties, with the highest reduction-oxidation potential including acidity. Several enzymes, i.e., β-1,3-Glucanase, Putative peroxidase 27, Thaumatin-like protein, among others, were identified in the <10 kDa fraction, i.e., enzymes known to perform various functions in plant-based waste. Therefore, there is a need for the renewable energy industry to consider solely using pitcher fluids to pretreat mixed agro-waste for fermentable hydrolysates’ production, which can be used as liquid feedstock for the bioenergy and/or biorefinery industries for environmental pollution reduction.

Endophytic fungi: a potential source of industrial enzyme producers

Microbial enzymes have gained interest for their widespread use in various industries and medicine due to their stability, ease of production, and optimization. Endophytic fungi in plant tissues produce a wide range of secondary metabolites and enzymes, which exhibit a variety of biological activities. The present review illustrates promising applications of enzymes produced by endophytic fungi and discusses the characteristic features of the enzymes, application of the endophytic fungal enzymes in therapeutics, agriculture, food, and biofuel industries. Endophytic fungi producing ligninolytic enzymes have possible biotechnological applications in lignocellulosic biorefineries. The global market of industrially important enzymes, challenges, and future prospects are illustrated. However, the commercialization of endophytic fungal enzymes for industrial purposes is yet to be explored. The present review suggests that endophytic fungi can produce various enzymes and may become a novel source for upscaling the production of enzymes of industrial use.

Development of different pretreatments and related technologies for efficient biomass conversion of lignocellulose

Lignocellulose, a kind of biological resource widely existing in nature, which can be transformed into value-added biochemical products through saccharification, fermentation or chemical catalysis. Pretreatments are the necessary step to increase the accessibility and digestibility of lignocellulose. This paper comprehensively reviewed different pretreatment progress of lignocellulose in recent year, including mechanical/thermal, biological, inorganic solvent, organic solvent and unconventional physical-chemical pretreatments, focusing on quantifying the influence of pretreatments on subsequent biomass conversion. In addition, related pretreatment techniques such as genetic engineering, reactor configurations, downstream process and visualization technology of pretreatment were discussed. Finally, this review presented the challenge of lignocellulose pretreatment in the future.

Laccase-mediated delignification and detoxification of lignocellulosic biomass: removing obstacles in energy generation

The rising global population and worldwide industrialization have led to unprecedented energy demand that is causing fast depletion of fossil reserves. This has led to search for alternative energy sources that are renewable and environment friendly. Use of lignocellulosic biomass for energy generation is considered a promising approach as it does not compete with food supply. However, the lignin component of the biomass acts as a natural barrier that prevents its efficient utilization. In order to remove the lignin and increase the amount of fermentable sugars, the lignocellulosic biomass is pretreated using physical and chemical methods which are costly and hazardous for environment. Moreover, during the traditional pretreatment process, numerous inhibitory compounds are generated that adversely affect the growth of fermentative microbes. Alternatively, biological methods that use microbes and their enzymes disrupt lignin polymers and increase the accessibility of the carbohydrates for the sugar generation. Microbial laccases have been considered as an efficient biocatalyst for delignification and detoxification offering a green initiative for energy generation process. The present review aims to bring together recent studies in bioenergy generation using laccase biocatalyst in the pretreatment processes. The work provides an overview of the sustainable and eco-friendly approach of biological delignification and detoxification through whole-cell and enzymatic methods, use of laccase-mediator system, and immobilized laccases for this purpose. It also summarizes the advantages, associated challenges, and potential prospects to overcome the limitations.

Efficient decolorization of recalcitrant dyes at neutral/alkaline pH by a new bacterial laccase-mediator system

Laccases and laccase-mediator systems (LMS) are versatile catalysts that can oxidize a broad range of substrates coupled to the sole reduction of dioxygen to water. They possess many biotechnological applications in paper, textile, and food industries, bioethanol production, organic synthesis, detection and degradation of pollutants, and biofuel cell development. In particular, bacterial laccases are getting relevance due to their activity in a wide range of pH and temperature and their robustness under harsh conditions. However, the enzyme and the redox mediator's availability and costs limit their large-scale commercial use. Here we demonstrate that β-(10-phenothiazyl)-propionic acid can be used as an efficient and low-cost redox mediator for decolorizing synthetic dyes by the recombinant laccase SilA from Streptomyces ipomoeae produced in E. coli. This new LMS can decolorize more than 80% indigo carmine and malachite green in 1 h at pH = 8.0 and 2 h in tap water (pH = 6.8). Furthermore, it decolorized more than 40% of anthraquinone dye remazol brilliant blue R and 80% of azo dye xylidine ponceau in 5 h at 50 °C, pH 8.0. It supported at least 3 decolorization cycles without losing activity, representing an attractive candidate for a cost-effective and environmentally friendly LMS functional at neutral to alkaline pH.

Comparison of performances of different fungal laccases in delignification and detoxification of alkali-pretreated corncob for bioethanol production

The performance of the alkaline fungal laccase PIE5 (pH 8.5) in the delignification and detoxification of alkali-pretreated corncob to produce bioethanol was evaluated and compared with that of the neutral counterpart (rLcc9, 6.5), with the acidic laccase rLacA (4.0) was used as an independent control. Treatment with the three laccases facilitated bioethanol production compared with their respective controls. The lignin contents of alkali-pretreated corncob reduced from 4.06%, 5.06%, and 7.80% to 3.44%, 3.95%, and 5.03%, after PIE5, rLcc9, and rLacA treatment, respectively. However, the performances of the laccases were in the order rLacA > rLcc9 > PIE5 in terms of decreasing total phenol concentration (0.18, 0.36, and 0.67 g/l), boosting ethanol concentration (8.02, 7.51, and 7.31 g/l), and volumetric ethanol productivity (1.34, 0.94, and 0.91 g/l hr), and shortening overall fermentation time. Our results would inform future attempts to improve laccases for ethanol production. Furthermore, based on our data and the fact that additional procedures, such as pH adjustment, are needed during neutral/alkaline fungal laccase treatment, we suggest acidic fungal laccases may be a better choice than neutral/alkaline fungal laccases in bioethanol production.

Immobilization of Laccase on Magnetic Nanoparticles and Application in the Detoxification of Rice Straw Hydrolysate for the Lipid Production of Rhodotorula glutinis

The production of microbial lipid using lignocellulosic agroforestry residues has attracted much attention. But, various inhibitors such as phenols and furans, which are produced during lignocellulosic hydrolysate preparation, are harmful to microbial lipid accumulation. Herein, we developed a novel detoxification strategy of rice straw hydrolysate using immobilized laccase on magnetic Fe₃O₄ nanoparticles for improving lipid production of Rhodotorula glutinis. Compared with free laccase, the immobilized laccase on magnetic nanoparticles showed better stability, which still retained 76% of original activity at 70 °C and 56% at pH 2 for 6 h. This immobilized laccase was reused to remove inhibitors in acid-pretreated rice straw hydrolysate through recycling with external magnetic field. The results showed that most of phenols, parts of furans, and formic acids could be removed by immobilized laccase after the first batch. Notably, the immobilized laccase exhibited good reusability in repeated batch detoxification. 78.2% phenols, 43.8% furfural, 30.4% HMF, and 16.5% formic acid in the hydrolysate were removed after the fourth batch. Furthermore, these detoxified rice straw hydrolysates, as substrates, were applied to the lipid production of Rhodotorula glutinis. The lipid yield in detoxified hydrolysate was significantly higher than that in undetoxified hydrolysate. These findings suggest that the immobilized laccase on magnetic nanoparticles has a potential to detoxify lignocellusic hydrolysate for improving microbial lipid production.

Enzymatic removal of inhibitory compounds from lignocellulosic hydrolysates for biomass to bioproducts applications

The physicochemical pretreatment is an important step to reduce biomass recalcitrance and facilitate further processing of plant lignocellulose into bioproducts. This process results in soluble and insoluble biomass fractions, and both may contain by-products that inhibit enzymatic biocatalysts and microbial fermentation. These fermentation inhibitory compounds (ICs) are produced during the degradation of lignin and sugars, resulting in phenolic and furanic compounds, and carboxylic acids. Therefore, detoxification steps may be required to improve lignocellulose conversion by microoganisms. Several physical and chemical methods, such as neutralization, use of activated charcoal and organic solvents, have been developed and recommended for removal of ICs. However, biological processes, especially enzyme-based, have been shown to efficiently remove ICs with the advantage of minimizing environmental issues since they are biogenic catalysts and used in low quantities. This review focuses on describing several enzymatic approaches to promote detoxification of lignocellulosic hydrolysates and improve the performance of microbial fermentation for the generation of bioproducts. Novel strategies using classical carbohydrate active enzymes (CAZymes), such as laccases (AA1) and peroxidases (AA2), as well as more advanced strategies using prooxidant, antioxidant and detoxification enzymes (dubbed as PADs), i.e. superoxide dismutases, are discussed as perspectives in the field.

A critical review on current strategies and trends employed for removal of inhibitors and toxic materials generated during biomass pretreatment

The main objective of biomass pretreatment is to separate biomass components and provide easier access with ultimate aim for lignin removal, hemicellulose protection and cellulose crystallinity reduction. Effective bioconversion with least inhibitory compound production would play a considerable role in economic practicability of the process in order to achieve economic sustainability. In this regard, detoxification is an important condition to make biomass hydrolysate acquiescent to bioconversion; also, understanding of inhibitors effect on growth and fermentation are necessary requirements for system detoxification. A number of physical, chemical and biological methods like feedstock selection, membrane selection, neutralization, use of activated charcoal etc have been recommended and developed for removal or minimizing the inhibitory compounds effect. This work reviews various inhibitory compounds produced during pretreatment methods and their removal by various processes.

The first fungal laccase with an alkaline pH optimum obtained by directed evolution and its application in indigo dye decolorization

Engineering of fungal laccases with optimum catalytic activity at alkaline pH has been a long-lasting challenge. In this study, a mutant library containing 3000 clones was obtained by error-prone PCR to adapt the optimum pH of a fungal laccase Lcc9 from the basidiomycete Coprinopsis cinerea. After three rounds of functional screening, a mutant with three amino acid changes (E116K, N229D, I393T) named PIE5 was selected. PIE5 showed an optimum pH of 8.5 and 8.0 against guaiacol and 2,6-DMP when expressed in Pichia pastoris, representing the first fungal laccase that possesses an optimum pH at an alkaline condition. Site directed mutagenesis disclosed that N229D contributed the most to the optimum pH increment. A single N229D mutation caused an increase in optimum pH by 1.5 units. When used in indigo dye decolorization, PIE5 efficiently decolorized 87.1 ± 1.1% and 90.9 ± 0.3% indigo dye at the optimum conditions of pH 7.0-7.5 and 60 °C, and with either methyl 3,5-dimethoxy-4-hydroxybenzoate or 2,2'-azino-bis(3-ethylbenzothazoline-6-sulfonate) as the mediator. In comparison, the commercially available fungal laccase TvLac from Trametes villosa decolorized 84.3 ± 1.8% of indigo dye under its optimum conditions (opt. pH 5.0 and 60 °C). The properties of an alkaline-dependent activity and the high indigo dye decolorization ability (1.3-fold better than the parental Lcc9) make the new fungal laccase PIE5 an alternative for specific industrial applications.

A thermostable laccase from Thermus sp. 2.9 and its potential for delignification of Eucalyptus biomass

Laccases are multicopper oxidases that are being studied for their potential application in pretreatment strategies of lignocellulosic feedstocks for bioethanol production. Here, we report the expression and characterization of a predicted laccase (LAC_2.9) from the thermophilic bacterial strain Thermus sp. 2.9 and investigate its capacity to delignify lignocellulosic biomass. The purified enzyme displayed a blue color typical of laccases, showed strict copper dependence and retained 80% of its activity after 16 h at 70 °C. At 60 °C, the enzyme oxidized 2,2′-azino-di-(3-ethylbenzthiazoline sulfonate) (ABTS) and 2,6-dimethoxyphenol (DMP) at optimal pH of 5 and 6, respectively. LAC_2.9 had higher substrate specificity (k_cat/K_M) for DMP with a calculated value that accounts for one of the highest reported for laccases. Further, the enzyme oxidized a phenolic lignin model dimer. The incubation of steam-exploded eucalyptus biomass with LAC_2.9 and 1-hydroxybenzotriazole (HBT) as mediator changed the structural properties of the lignocellulose as evidenced by Fourier transform infrared (FTIR) spectroscopy and thermo-gravimetric analysis (TGA). However, this did not increase the yield of sugars released by enzymatic saccharification. In conclusion, LAC_2.9 is a thermostable laccase with potential application in the delignification of lignocellulosic biomass.

Biodelignification and hydrolysis of rice straw by novel bacteria isolated from wood feeding termite

In this study, two bacterial strains capable of degrading lignin, cellulose, and hemicellulose were isolated from wood feeding termite. The isolates were identified by 16S rRNA gene sequencing. A bacterium Ochrobactrum oryzae BMP03 capable of degrading lignin was isolated on alkali lignin medium and Bacillus sp. BMP01 strain capable of degrading cellulose and hemicellulose were isolated on carboxymethyl cellulose and xylan media. The efficiency of bacterial degradation was studied by evaluating the composition of rice straw both before and after degradation. The appearance of new cellulose bands at 1382, 1276, 1200, and 871 cm-1, and the absence of former lignin bands at 1726, 1307, and 1246 cm-1 was observed after biodelignification. This was further confirmed by the formation of channeling and layering of the microstructure of biodelignified rice straw observed under electron microscope. Maximum lignin removal was achieved in separate biodelignification and hydrolysis process after the 14th day of treatment by Ochrobactrum oryzae BMP03 (53.74% lignin removal). Hydrolysis of the biodelignified rice straw released 69.96% of total reducing sugars after the 14th day hydrolysis by Bacillus sp. BMP01. In simultaneous delignification and hydrolysis process, about 58.67% of total reducing sugars were obtained after the 13th day of biotreatment. Separate delignification and hydrolysis process were found to be effective in lignin removal and sugar released than the simultaneous process. The bacteria, Bacillus sp. BMP01, has the ability to degrade hemicellulose and cellulose simultaneously. Overall, these results demonstrate that the possibility of rice straw bioconversion into reducing sugars by bacteria from termite gut.