Simultaneous Capillary Liquid Chromatography Determination of Drugs in Pharmaceutical Preparations Using Tunable Platforms of Polymethacrylate Monolithic Columns Modified with Octadecylamine

Monolithic stationary phases prepared via cyclic anhydride ring-opening polymerization as tunable platforms for chromatographic applications

Polymer monolithic stationary phases were prepared based on a cyclic anhydride as a reactive and tunable platform via ring-opening post-polymerization using primary amines, octadecylamine and benzylamine. The characterization techniques indicated the insertion of the functional groups into the original monoliths and confirmed the amidation reactions. The post-polymerization modification also improved the monolith's thermal and mechanical stability and induced significant improvement in their surface area. The stationary phases were synthesized inside small dimension stainless-steel columns (2.1 mm i.d. × 50 mm length). The prepared columns before and after modifications have been tested for the separation of the alkylbenzene series and some polycyclic aromatic hydrocarbons (PAHs) as model compounds. In all cases, the chromatographic performance in terms of the height equivalent to a theoretical plate on the functionalized monoliths was remarkably improved when compared with that on the unmodified monolith, which was between 9.59-39.49 μm and 4.08-31.50 μm using monoliths modified with octadecylamine and benzylamine, respectively. Under the same chromatographic conditions, the functionalization of monoliths with octadecylamine provided more hydrophobic interactions and enhanced the retention of alkylbenzenes, while the modification of monoliths with benzyl groups improved the separation and the retention of the PAHs through the strong π-π interactions. However, post-modification polymerization with octadecylamine and benzylamine enhanced the separation efficiency of the prepared columns toward all studied compounds. The repeatability of the injections on the same column and the reproducibility of the prepared columns have been studied for some selected parameters and estimated in terms of percent relative standard deviation (%RSD) for some of the studied compounds. The repeatability of the prepared columns was ≤9.42% (n = 5) based on run-to-run injections and ≤9.48% based on day-to-day injections for five successive days. The reproducibility levels, on the other hand, were ≤20.95% for all studied parameters in all cases. To assess their performance for the analysis of real samples, the applicability of the prepared columns was examined for the separation of the active ingredients extracted from some commercial pharmaceutical formulations and for the separation of tea water extract constituents. The validation data show the suitability of the columns for practical use in the routine analysis of these samples.

Montmorillonite-based polymethacrylate composite monoliths as stationary phase materials for food and pharmaceutical analysis in capillary liquid and gas chromatography

This work relates to the preparation of novel and promising stationary phases containing inorganic-organic composites for capillary liquid and gas chromatography. A naturally occurring montmorillonite was introduced to polymethacrylate monoliths, then used under different conditions of GC and HPLC at the same time. The performance of the columns was evaluated for the separation of alkane and alkylbenzene series in GC and capillary HPLC, respectively. While the bare monoliths failed to separate the model analytes, montmorillonite-based polymethacrylate allowed a full separation of the mixtures with R_s≥1.42. The columns were applied for the determination of myrcene and limonene isomers in the peel extracts of some fruits using GC, and for the analysis of active ingredients including aspirin, vitamin-C, caffeine, and ibuprofen extracted from common drugs using capillary HPLC. In GC, fast separation was achieved in 1.0 min with R_s of 6.53. The columns exhibited the best efficiency for myrcene with 20,900 plates/m. Using the capillary HPLC columns, the active ingredients were resolved in 10 min with R_s≥5.72. The efficiency values located between 12,800-21,700 plates/m in all cases. The developed methods were found to be linear in the range of 0.10-10.0 and 0.20-180 μg/mL for GC and HPLC, respectively. In comparison with commercial columns, the results in GC methods reveal that, despite their much shorter length, the prepared columns proved a faster separation with higher efficiency and comparable detection limits and chromatographic resolution. The prepared HPLC capillaries exposed lower run times and detection limits with comparable efficiency and resolution, and consume fewer samples and mobile phase solvents. The results demonstrate that the montmorillonite-based polymethacrylate composites are applicable as stationary phases for routine analysis and quality control of important fields such as food and pharmaceutical samples.

Naturally Occurring Montmorillonite-Based Polymer Monolith Composites as Stationary Phases for Capillary Liquid and Gas Chromatography

This work is associated with the preparation of capillary chromatographic columns containing inorganic-organic composites comprised of naturally occurring montmorillonite (MMT) clay mineral and polymethacrylate monolithic material. The prepared composites combine the best qualities of both constituents, offering desirable properties for use under the disparate conditions of both GC and HPLC at the same time. The stationary phases were investigated by scanning electron microscopy (SEM), the specific surface area, and thermogravimetric analysis (TGA) and examined in terms of various conditions utilized for GC and HPLC methods. The prepared columns demonstrated an excellent permeability and stability against common chromatographic conditions, such as the eluent type, flow rate, pressure, and temperature. The results confirmed that the addition of small amounts of MMT into the monolith induced significant improvement in the specific surface area, which contributed to the formation of more active sites and enhanced the retention of analytes. The registered column backpressures did not exceed 980 kPa and 16,500 kPa for the prepared GC and HPLC columns, respectively. The prepared columns were subjected to the separation of various interesting compounds possessing different chemistries and polarities, including alkanes, alkylbenzenes, polycyclic aromatic hydrocarbons (PAHs), alcohols, ketones, phenols, some common organic solvents, and isomeric mixtures. Under the optimal conditions, the efficiency of the columns fell between 4900–38,500 plates m−1 for GC and 3400–58,800 plates m−1 for capillary HPLC applications. In all cases, the measured chromatographic resolution was more than 1.38, with excellent an peak symmetry and low tailing factors. In comparison with the most commonly used commercial columns, the polysiloxane open tubular column for GC and silica-based C18 packed column for HPLC, the prepared GC columns demonstrated a faster separation with a higher efficiency, comparable resolution and tailing factors, and lower consumption of carrier gas. Regarding the capillary columns prepared for HPLC, the chromatographic experiments exposed a much lower run time with a comparable efficiency and resolution and drastically lower consumption of mobile phase solvents and samples. The results demonstrate that the MMT-based polymethacrylate monolith composites are applicable as novel and promising separation media for analyzing various mixtures of interest in different fields, such as petrochemical and environmental samples.