A novel method for processing adipose-derived stromal stem cells using a closed cell washing concentration device with a hollow fiber membrane module

Laser-activated autologous adipose tissue-derived stromal vascular fraction restores spinal cord architecture and function in multiple sclerosis cat model

BACKGROUND

Multiple sclerosis (MS) is the most frequent non-traumatic neurological debilitating disease among young adults with no cure. Over recent decades, efforts to treat neurodegenerative diseases have shifted to regenerative cell therapy. Adipose tissue-derived stromal vascular fraction (SVF) comprises a heterogeneous cell population, considered an easily accessible source of MSCs with therapeutic potential in autoimmune diseases. This study aimed to assess the regenerative capacity of low-level laser-activated SVF in an MS cat model.

METHODS

Fifteen adult Persian cats were used in this study: Group I (control negative group, normal cats), Group II (EB-treated group, induced for MS by ethidium bromide (EB) intrathecal injection), and Group III (SVF co-treated group, induced for MS then treated with SVF on day 14 post-induction). The SVF was obtained after digesting the adipose tissue with collagenase type I and injecting it intrathecal through the foramen magnum.

RESULTS

The results showed that the pelvic limb's weight-bearing locomotion activity was significantly (P ≤ 0.05) recovered in Group III, and the Basso, Beattie, and Bresnahan (BBB) scores of hindlimb locomotion were significantly higher in Group III (14 ± 0.44) than Group II (4 ± 0.31). The lesion's extent and intensity were reduced in the magnetic resonance imaging (MRI) of Group III. Besides, the same group showed a significant increase in the expression of neurotrophic factors: BDNF, SDF and NGF (0.61 ± 0.01, 0.51 ± 0.01 and 0.67 ± 0.01, respectively) compared with Group II (0.33 ± 0.01, 0.36 ± 0.006 and 0.2 ± 0.01, respectively). Furthermore, SVF co-treated group revealed a significant (P ≤ 0.05) increase in oligodendrocyte transcription factor (Olig2) and myelin basic protein (4 ± 0.35 and 6 ± 0.45, respectively) that was decreased in group II (1.8 ± 0.22 and 2.9 ± 0.20, respectively). Moreover, group III showed a significant (P ≤ 0.05) reduction in Bax and glial fibrillary acidic protein (4 ± 0.53 and 3.8 ± 0.52, respectively) as compared with group II (10.7 ± 0.49 and 8.7 ± 0.78, respectively). The transmission electron microscopy demonstrated regular more compact, and markedly (P ≤ 0.05) thicker myelin sheaths (mm) in Group III (0.3 ± 0.006) as compared with group II (0.1 ± 0.004). Based on our results, the SVF co-treated group revealed remyelination and regeneration capacity with a reduction in apoptosis and axonal degeneration.

CONCLUSION

SVF is considered an easy, valuable, and promising therapeutic approach for treating spinal cord injuries, particularly MS.

A New Classification for Adipose-derived Stromal-cell Systems

Obtaining regenerative cells from adipose tissue and their clinical use has become one of the most popular subjects of plastic surgery. However, there is no accepted classification in terms of methods. In this study, classification is proposed for the first time as a new idea. Accordingly, stromal cells can be obtained from adipose tissue by two approaches: direct methods for the bonds between parenchymal and stromal cells, and indirect methods, which target parenchymal cells rather than strong bonds, and increase the stromal cell ratio relatively. These methods can also be subclassified as fat (+), fat (-), fat (±) in terms of using the remaining fat in the final product as a graft. Direct methods include adinizing and enzymatic techniques; indirect methods include emulsification and micro-fragmentation/micronization techniques. In the enzymatic method, the fat tissue in the final product is considered dirty because it contains enzymes and must be discarded. That is why it is a fat (-) method. The adinizing method using ultra-sharp blades is fat (+) because the adipose tissue after the procedure can be used. Because the fat tissue is exposed to blunt pressure in emulsification techniques, it cannot be used as a graft. Thus, these are fat (-) methods. In micronization techniques using filter systems, there may still be intact adipocytes; therefore, it should be classified as fat (±). Adinizing provides both the highest efficiency and the full use of the end product. This classification will guide clinicians in terms of choosing the right product.

Cell-Assisted Lipotransfer in Breast Augmentation Surgery: Clinical Outcomes and Considerations for Future Research

Autologous fat transfer is a widely used surgical technique, chosen by numerous plastic surgeons for breast augmentation surgery. This technique is based on three steps: 1. harvesting of the lipoaspirate from the patient, 2. centrifugation and removal of the top, oily, layer, and 3. implantation in the patient’s breast(s). It has been associated with various complications, including post-surgical fat resorption, as measured quantitatively with MRI, CT, and other 3D-quantification systems.

Adipose-derived stem cells have been explored as a means of addressing fat resorption. They can be separated from the lipoaspirate following centrifugation, and enzymatically purified from unwanted debris, with collagenase, forming the stromal vascular fraction. The stromal vascular fraction is then recombined with the graft volume prior to implantation. This novel technique, referred to as “cell-assisted lipotransfer”, has shown promising results in terms of reducing fat resorption. These results are due to the pro-angiogenic and pro-adipogenic ability of the stem cells, which allow the graft to address the conditions of ischemia more effectively than autologous fat transfer.

The aim of this review is to explore the ways in which cell-assisted lipotransfer is different from the autologous fat transfer, as well as how and why adipose-derived stem cells may contribute towards limiting fat resorption. The immunological background of these cells is discussed in detail, while grounds for further development are discussed, by means of the administration of external growth factors, which could, potentially, maximize outcomes, while limiting complications.

Advances in automated cell washing and concentration

The successful commercialization of cell therapies requires thorough planning and consideration of product quality, cost and scale of the manufacturing process. The implementation of automation can be central to a robust and reproducible manufacturing process at industrialized scales. There have been a number of wash-and-concentrate devices developed for cell manufacturing. These technologies have arisen from transfusion medicine, hematopoietic stem cell and biologics manufacturing where operating mechanisms are distinct from manual centrifugation. This review describes the historical origin and fundamental technologies underlying each currently available wash-and-concentrate device as well as their relative advantages and disadvantages in cell therapy applications. Understanding the specific attributes and limitations of these technologies is essential to optimizing cell therapy manufacturing.