Beyond Nanoparticles: The Role of Sub-nanosized Metal Species in Heterogeneous Catalysis

Optimized Pt-Co Alloy Nanoparticles for Reverse Water-Gas Shift Activation of CO2

Different Co contents were used to tune bimetallic Pt-Co nanoparticles with a diameter of 8 nm, resulting in Pt:Co ratios of 3.54, 1.51, and 0.96. These nanoparticles were then applied to the MCF-17 mesoporous silica support. The synthesized materials were characterized with HR-TEM, HAADF-TEM, EDX, XRD, BET, ICP-MS, in situ DRIFTS, and quasi in situ XPS techniques. The catalysts were tested in a thermally induced reverse water-gas shift reaction (CO2:H2 = 1:4) at atmospheric pressure in the 200-700 °C temperature range. All bimetallic Pt-Co particles outperformed the pure Pt benchmark catalyst. The nanoparticles with a Pt:Co ratio of 1.51 exhibited 2.6 times higher activity and increased CO selectivity by 4% at 500 °C. Experiments proved that the electron accumulation and alloying effect on the Pt-Co particles are stronger with higher Co ratios. The production of CO followed the formate reaction pathway on all catalysts due to the face-centered-cubic structure, which is similar to the Pt benchmark. It is concluded that the enhanced properties of Co culminate at a Pt:Co ratio of 1.51 because decreasing the ratio to 0.96 results in lower activity despite having more Co atoms available for the electronic interaction, resulting in the lack of electron-rich Pt sites.

Partial Methane Oxidation in Fuel Cell-Type Reactors for Co-Generation of Energy and Chemicals: A Short Review

The conversion of methane into chemicals is of interest to achieve a decarbonized future. Fuel cells are electrochemical devices commonly used to obtain electrical energy but can be utilized either for chemicals’ production or both energy and chemicals cogeneration. In this work, the partial oxidation of methane in fuel cells for electricity generation and valuable chemicals production at the same time is reviewed. For this purpose, we compile different types of methane-fed fuel cells, both low- and high-temperature fuel cells. Despite the fact that few studies have been conducted on this subject, promising results are driving the development of fuel cells that use methane as a fuel source for the cogeneration of power and valuable chemicals.

Constructing g-C3N4/Cd1−xZnxS-Based Heterostructures for Efficient Hydrogen Production under Visible Light

Two types of photocatalysts, 1%Pt/Cd1−xZnxS/g-C3N4 (x = 0.2–0.3) and Cd1−xZnxS/1%Pt/g-C3N4 (x = 0.2–0.3), were synthesized by varying the deposition order of platinum, and a solid solution of cadmium and zinc sulfides onto the surface of g-C3N4. The characterization of photocatalysts showed that, for 1%Pt/Cd1−xZnxS/g-C3N4, small platinum particles were deposited onto a solid solution of cadmium and zinc sulfides; in the case of Cd1−xZnxS/1%Pt/g-C3N4, enlarged platinum clusters were located on the surface of graphitic carbon nitride. Based on the structure of the photocatalysts, we assumed that, in the first case, type II heterojunctions and, in the latter case, S-scheme heterojunctions were realized. The activity of the synthesized samples was tested in hydrogen evolution from triethanolamine (TEOA) basic solution under visible light (λ = 450 nm). A remarkable increase in hydrogen evolution rate compared to single-phase platinized 1%Pt/Cd1−xZnxS photocatalysts was observed only in the case of ternary photocatalysts with platinum located on the g-C3N4 surface, Cd1−xZnxS/1%Pt/g-C3N4. Thus, we proved using kinetic experiments and characterization techniques that, for composite photocatalysts based on Cd1−xZnxS and g-C3N4, the formation of the S-scheme mechanism is more favorable than that for type II heterojunction. The highest activity, 2.5 mmol H2 g−1 h−1, with an apparent quantum efficiency equal to 6.0% at a wavelength of 450 nm was achieved by sample 20% Cd0.8Zn0.2S/1% Pt/g-C3N4.

Photocatalytic Applications of Metal Oxides for Sustainable Environmental Remediation

Along with industrialization and rapid urbanization, environmental remediation is globally a perpetual concept to deliver a sustainable environment. Various organic and inorganic wastes from industries and domestic homes are released into water systems. These wastes carry contaminants with detrimental effects on the environment. Consequently, there is an urgent need for an appropriate wastewater treatment technology for the effective decontamination of our water systems. One promising approach is employing nanoparticles of metal oxides as photocatalysts for the degradation of these water pollutants. Transition metal oxides and their composites exhibit excellent photocatalytic activities and along show favorable characteristics like non-toxicity and stability that also make them useful in a wide range of applications. This study discusses some characteristics of metal oxides and briefly outlined their various applications. It focuses on the metal oxides TiO2, ZnO, WO3, CuO, and Cu2O, which are the most common and recognized to be cost-effective, stable, efficient, and most of all, environmentally friendly for a sustainable approach for environmental remediation. Meanwhile, this study highlights the photocatalytic activities of these metal oxides, recent developments, challenges, and modifications made on these metal oxides to overcome their limitations and maximize their performance in the photodegradation of pollutants.

Treatment of Produced Water with Photocatalysis: Recent Advances, Affecting Factors and Future Research Prospects

Produced water is the largest byproduct of oil and gas production. Due to the complexity of produced water, especially dissolved petroleum hydrocarbons and high salinity, efficient water treatment technologies are required prior to beneficial use of such waste streams. Photocatalysis has been demonstrated to be effective at degrading recalcitrant organic contaminants, however, there is limited understanding about its application to treating produced water that has a complex and highly variable water composition. Therefore, the determination of the appropriate photocatalysis technique and the operating parameters are critical to achieve the maximum removal of recalcitrant compounds at the lowest cost. The objective of this review is to examine the feasibility of photocatalysis-involved treatment for the removal of contaminants in produced water. Recent studies revealed that photocatalysis was effective at decomposing recalcitrant organic compounds but not for mineralization. The factors affecting decontamination and strategies to improve photocatalysis efficiency are discussed. Further, recent developments and future research prospects on photocatalysis-derived systems for produced water treatment are addressed. Photocatalysis is proposed to be combined with other treatment processes, such as biological treatments, to partially reduce total organic carbon, break down macromolecular organic compounds, increase biodegradability, and reduce the toxicity of produced water.

The Potassium-Induced Decomposition Pathway of HCOOH on Rh(111)

Formic acid (FA) can be considered both a CO and a H2 carrier via selective dehydration and dehydrogenation pathways, respectively. The two processes can be influenced by the modification of the active components of the catalysts used. In the present study the adsorption of FA and the decomposition of the formed formate intermediate were investigated on potassium promoted Rh(111) surfaces. The preadsorbed potassium markedly increased the uptake of FA at 300 K, and influenced the decomposition of formate depending on the potassium coverage. The work function (Δϕ) is increased by the adsorption of FA on K/Rh(111) at 300 K suggesting a large negative charge on the chemisorbed molecule, which could be probably due to the enhanced back-donation of electrons from the K-promoted Rh into an empty π orbital of HCOOH. The binding energy of the formate species is therefore increased resulting in a greater concentration of irreversibly adsorbed formate species. Decomposition of the formate species led to the formation of H2, CO2, H2O, and CO, which desorbed at significantly higher temperatures from the K-promoted surface than from the K-free one as it was proven by thermal desorption studies. Transformation of surface formate to carbonate (evidenced by UPS) and its decomposition and desorption is responsible for the high temperature CO and CO2 formation.

Rh-induced Support Transformation and Rh Incorporation in Titanate Structures and Their Influence on Catalytic Activity

Rh is one of the most effective metals in several technologically important heterogeneous catalytic reactions, like the hydrogenation of CO2, and CO, the CO+H2O reaction, and methane and ethanol transformations. Titania and titanates are among the most frequently studied supports for Rh nanoparticles. The present study demonstrates that the nature of the support has a marked influence on the specific activity. For comparison, the catalytic activity of TiO2 P25 is also presented. It is pointed out that a certain amount of Rh can be stabilized as cation (Rh+) in ion-exchange positions (i.e., in atomic scale distribution) of the titanate framework. This ionic form does not exists on TiO2. We pay distinguished attention not only to the electronic interaction between Rh metal and the titania/titanate support, but also to the Rh-induced phase transitions of one-dimensional titanate nanowires (TiONW) and nanotubes (TiONT). Support transformation phenomena can be observed in Rh-loaded titanates. Rh decorated nanowires transform into the TiO2(B) phase, whereas their pristine counterparts recrystallize into anatase. The formation of anatase is dominant during the thermal annealing process in both acid-treated and Rh-decorated nanotubes; Rh catalysis this transformation. We demonstrate that the phase transformations and the formation of Rh nanoclusters and incorporated Rh ions affect the conversion and the selectivity of the reactions. The following initial activity order was found in the CO2 + H2, CO + H2O and C2H5OH decomposition reactions: Rh/TiO2 (Degussa P25) ≥ Rh/TiONW > Rh/TiONT. On the other hand it is remarkable that the hydrogen selectivity in ethanol decomposition was two times higher on Rh/TiONW and Rh/TiO(NT) catalysts than on Rh/TiO2 due to the presence of Rh+ cations incorporated into the framework of the titanate structures.

New Insight on the Formation of Sodium Titanates 1D Nanostructures and Its Application on CO2 Hydrogenation

The aim of this work is focused on the study of a series of non-traditional catalytic nanomaterials to transform greenhouse CO₂ gas into added-value products. We found encouraging results of CO₂ hydrogenation activity over sodium titanates with different morphologies. The yield to methanol increases with the increase in the Na incorporated in the nanostructures confirming the proposed mechanism. Samples were prepared at different times of hydrothermal treatment (HTT) with NaOH solutions, and these materials were labeled as Ti-nR-x with x as the hours on the HTT. HRTEM initially showed sphere-shaped nanoparticles in the TiO₂ commercial nanopowder, increasing the HTT resulted in morphological changes in which the structures passed from nanosheets and finally to nanorods after 30 h. The X-ray diffraction and Raman spectroscopy results indicated the formation of sodium titanates such as Na₂Ti₃O₇ with short Ti-O bonds and that Na begins to be incorporated into the distorted TiO₆ crystalline structure after 5 h of HTT (until 12 wt%). The crystalline and shape transformation resulted in a significant modification on the textural properties passing from 51 m².g⁻¹ to 150 m².g⁻¹ and from a pore volume of 0.12 cm³.g⁻¹ to 1.03 cm³.g⁻¹ for Ti-ref and Ti-nR-30 respectively. We also observed differences in the electronic properties as the bandgap presented a blue shift from 3.16 eV on the TiO₂ reference nano-powder to 3.44 eV for the Ti-nR-30 calcined sample. This fact coincides with the presence of a more electron-rich state of the Ti⁴⁺ and the formation of negative charge layer induced by the presence of Na⁺ interlayer cations detected by XPS analysis, at the same this helped us to explain the catalytic activity results.