Selective Catalytic Reduction of NOx with NH3 on Cu-BTC-derived Catalysts: Influence of Modulation and Thermal Treatment

Remarkable N2-selectivity enhancement of NH3-SCR over HPMo modified MnCo-BTC@SiO2 catalyst

In this work, the phosphomolybdate (HPMo) modification strategy was applied to improve the N2 selectivity of MnCo-BTC@SiO2 catalyst for the selective catalytic reduction of NOx, and further, the mechanism of HPMo modification on enhanced catalytic performance was explored. Among MnCo-BTC@SiO2-x catalysts with different HPMo concentrations, MnCo-BTC@SiO2-0.75 catalyst exhibited not only the highest NH3-SCR performance (∼95% at 200-300°C) but also the best N2 selectivity (exceed 80% at 100-300°C) due to the appropriate redox capacity, greater surface acidity. X-ray photoelectron spectrometer (XPS) and temperature programmed reduction of H2 (H2-TPR) results showed that the modification with HPMo reduced the oxidation-reduction performance of the catalyst due to electron transfer from Mo5+ to Mn4+/Mn3+ and prevent the excessive oxidation of ammonia adsorption species. NH3 temperature-programmed desorption of (NH3-TPD) results showed that the modification with HPMo could significantly improve the surface acidity and NH3 adsorption, which enhance the catalytic activity and N2 selectivity. In-situ diffused reflectance infrared Fourier transform spectroscopy (in-situ DRIFTS) revealed that modification with HPMo increased significantly the amount of adsorbed NH3 species on the Bronsted acid site and CB/CL, it suppressed the production of N2O by inhibiting the production of NH species, the deep dehydrogenation of ammonia adsorption species. This study provided a simple design strategy for the catalyst to improve the low-temperature catalytic performance and N2 selectivity.

MOF-based catalysts: insights into the chemical transformation of greenhouse and toxic gases

Metal-organic framework (MOF)-based catalysts are outstanding alternative materials for the chemical transformation of greenhouse and toxic gases into high-add-value products. MOF catalysts exhibit remarkable properties to host different active sites. The combination of catalytic properties of MOFs is mentioned in order to understand their application. Furthermore, the main catalytic reactions, which involve the chemical transformation of CH4, CO2, NOx, fluorinated gases, O3, CO, VOCs, and H2S, are highlighted. The main active centers and reaction conditions for these reactions are presented and discussed to understand the reaction mechanisms. Interestingly, implementing MOF materials as catalysts for toxic gas-phase reactions is a great opportunity to provide new alternatives to enhance the air quality of our planet.

Progress in Metal-Organic Framework Catalysts for Selective Catalytic Reduction of NOx: A Mini-Review

Nitrogen oxides released from the combustion of fossil fuels are one of the main air pollutants. Selective catalytic reduction technology is the most widely used nitrogen oxide removal technology in the industry. With the development of nanomaterials science, more and more novel nanomaterials are being used as catalysts for the selective reduction of nitrogen oxides. In recent years, metal-organic frameworks (MOFs), with large specific surface areas and abundant acid and metal sites, have been extensively studied in the selective catalytic reduction of nitrogen oxides. This review summarizes recent progress in monometallic MOFs, bimetallic MOFs, and MOF-derived catalysts for the selective catalytic reduction of nitrogen oxides and compares the reaction mechanisms of different catalysts. This article also suggests the advantages and disadvantages of MOF-based catalysts compared with traditional catalysts and points out promising research directions in this field.

Construction of Cu-BTC by carboxylic acid organic ligand and its application in low temperature SCR denitration

The removal of NO has always been a hot issue in the treatment of coal-fired flue gas. In this paper, a hydrothermal synthesis method was used to prepare porous denitration catalysts with polycarboxyl organic isomers (trimellitic acid, phthalic acid, and benzoic acid). And then developed as the NO removing catalysts for low temperature selective catalytic reduction (SCR) with NH₃. XRD, BET, SEM, FTIR, XPS, Raman, H₂-TPR, NH₃-TPD and TG were used to analyze the crystallinity, microscopic morphology, surface functional groups and metal content. The results showed that: (1) From the crystal structure analysis, the catalyst prepared with 1,3,5 and 1,2,4-benzenetricarboxylic acid as ligands (1,3,5-A and 1,2,4-B) was Cu-BTC. (2) 1,3,5-A catalyst had a huge specific surface area, up to 1421.32 m²/g, and a pore volume up to 0.5798 cm³/g. (3) The prepared catalysts were applied to NH₃-SCR denitration, and the catalyst with Cu-BTC structure had relatively high catalytic performance, and the overall catalytic capacity showed an increasing trend with the temperature. (4) 1,3,5-A catalyst had stability and catalytic activity. When the temperature was 270 °C, the denitration efficiency reached 83.87%. And within 8 h, the denitration efficiency was stable up to 82%.

Synthesis of metal–organic frameworks (MOFs) and their application in the selective catalytic reduction of NOx with NH3

This review summarizes the synthesis, applications for the NH3-SCR and methods for strengthening the water resistance and thermal stability of MOF catalysts.

Atomically Dispersed Copper Sites in a Metal-Organic Framework for Reduction of Nitrogen Dioxide

Metal–organic framework (MOF) materials provide an excellent platform to fabricate single-atom catalysts due to their structural diversity, intrinsic porosity, and designable functionality. However, the unambiguous identification of atomically dispersed metal sites and the elucidation of their role in catalysis are challenging due to limited methods of characterization and lack of direct structural information. Here, we report a comprehensive investigation of the structure and the role of atomically dispersed copper sites in UiO-66 for the catalytic reduction of NO₂ at ambient temperature. The atomic dispersion of copper sites on UiO-66 is confirmed by high-angle annular dark-field scanning transmission electron microscopy, electron paramagnetic resonance spectroscopy, and inelastic neutron scattering, and their location is identified by neutron powder diffraction and solid-state nuclear magnetic resonance spectroscopy. The Cu/UiO-66 catalyst exhibits superior catalytic performance for the reduction of NO₂ at 25 °C without the use of reductants. A selectivity of 88% for the formation of N₂ at a 97% conversion of NO₂ with a lifetime of >50 h and an unprecedented turnover frequency of 6.1 h^–1 is achieved under nonthermal plasma activation. In situ and operando infrared, solid-state NMR, and EPR spectroscopy reveal the critical role of copper sites in the adsorption and activation of NO₂ molecules, with the formation of {Cu(I)···NO} and {Cu···NO₂} adducts promoting the conversion of NO₂ to N₂. This study will inspire the further design and study of new efficient single-atom catalysts for NO₂ abatement via detailed unravelling of their role in catalysis.