Electro-oxidation of ceftazidime in real municipal wastewater using PbO2–Ce and SnO2–Sb electrodes: influence of electrolyte and degradation pathway

Simultaneous Determination of Ceftazidime in Three Different Pharmaceutical Preparations Combined with Either Tazobactam, Tobramycin or Sulbactam by HPTLC-Spectrodensitometric Method

A new, simple hight performance thin layer chromatography (HPTLC)-Spectrodensitometric strategy was created and approved for the synchronous estimation of four antibacterial specialists: ceftazidime (CEF), tazobactam (TAZ), tobramycin (TOB) and sulbactam (SUL). The four compounds were separated on TLC aluminum plates covered with silica gel 60 F254, using chloroform-acetonitrile-methanol-ammonia (4:1:0.5:0.15, v/v/v/v) as a mobile phase at 254 nm. Linear correlation was obeyed over the concentration ranges of 12.0-72.0, 2.0-12.0, 3.0-18.0 and 10.0-50.0 μg mL-1 for CEF, TAZ, TOB and SUL, respectively. The proposed approach is efficient, repeatable and convenient as a flexible method for the quality control of diverse combinations of these pharmaceuticals in various pharmaceutical preparations, with high percent recoveries that are highly consistent with labeled data. When the findings of the proposed technique were compared to those of the comparison methods, there were no critical contrasts in terms of precision and accuracy.

The evaluation of parameter effects on cefoperazone treatability with new generation anodes

In this study it was aimed to investigate the treatability of cefoperazone with new generation Sb-doped SnO₂-Ni anodes. For this purpose, it was studied with Sn/Sb/Ni: 500/8/1 anodes for the oxidation of aqueous solution containing cefoperazone antibiotic by addition of different types of electrolyte. Potassium chloride was found as the best electrolyte type affecting the electrochemical reactions positively even at lower concentrations (750 mg/L⁻¹). At pH 8 the best results were obtained, which is the neutral pH value of the aqueous solution. 50 mA/cm² was found as the best value for current density parameter, providing full mineralization just after 60 min of reaction. The removal efficiencies increased generally with the increase of current density, because active oxidants occur increasingly at higher current values. According to the results of the study it was seen that, electrochemical oxidation processes with Sn/Sb/Ni–Ti anodes could be carried out efficiently without need adding extra electrolyte (salt) and pH adjustment step for real wastewaters containing antibiotics. Thus, it was found an easy and economic way to perform electrochemical oxidation with Sn/Sb/Ni–Ti anodes for the wastewaters containing cefoperazone antibiotics.

Efficient removal of antibiotics from water resources is a public health priority: a critical assessment of the efficacy of some remediation strategies for antibiotics in water

This review discusses the fundamental principles and mechanism of antibiotic removal from water of some commonly applied treatment techniques including chlorination, ozonation, UV-irradiation, Fenton processes, photocatalysis, electrochemical-oxidation, plasma, biochar, anaerobicdigestion, activated carbon and nanomaterials. Some experimental shortfalls identified by researchers such as certain characteristics of degradation agent applied and the strategies explored to override the identified limitations are briefly discussed. Depending on interactions of a range of factors including the type of antibiotic compound, operational parameters applied such as pH, temperature and treatment time, among other factors, all reviewed techniques can eliminate or reduce the levels of antibiotic compounds in water to varying extents. Some of the reviewed techniques such as anaerobic digestion generally require longer treatment times (up to 360, 193 and 170 days, according to some studies), while others such as photocatalysis achieved degradation within short contact time (within a minimum of 30, but up to 60, 240, 300 and 1880 minutes, in some cases). For some treatment techniques such as ozonation and Fenton, it is apparent that subjecting compounds to longer treatment times may improve elimination efficiency, whereas for some other techniques such as nanotechnology, application of longer treatment time generally meant comparatively minimal elimination efficiency. Based on the findings of experimental studies summarized, it is apparent that operational parameters such as pH and treatment time, while critical, do not exert sole or primary influence on the elimination percentage(s) achieved. Elimination efficiency achieved rather seems to be due more to the force of a combination of several factors.

A state of the art review on electrochemical technique for the remediation of pharmaceuticals containing wastewater

Pharmaceutical wastewater is a frequent kind of wastewater with high quantities of organic pollutants, although little research has been done in the area. Pharmaceutical wastewaters containing antibiotics and high salinity may impair traditional biological treatment, resulting in the propagation of antibiotic resistance genes. The potential for advanced oxidation processes (AOPs) to break down hazardous substances instead of present techniques that essentially transfer contaminants from wastewater to sludge, a membrane filter, or an adsorbent has attracted interest. Among a variety of AOPs, electrochemical systems are a feasible choice for treating pharmaceutical wastewater. Many electrochemical approaches exist now to remediate rivers polluted by refractory organic contaminants, like pharmaceutical micro-pollutants, which have become a severe environmental problem. The first part of this investigation provides the bibliometric analysis of the title search from 1970 to 2021 for keywords such as wastewater and electrochemical. We have provided information on relations between keywords, countries, and journals based on three fields plot, inter-country co-authorship network analysis, and co-occurrence network visualization. The second part introduces electrochemical water treatment approaches customized to these very distinct discarded flows, containing how processes, electrode materials, and operating conditions influence the results (with selective highlighting cathode reduction and anodic oxidation). This section looks at how electrochemistry may be utilized with typical treatment approaches to improve the integrated system's overall efficiency. We discuss how electrochemical cells might be beneficial and what compromises to consider when putting them into practice. We wrap up our analysis with a discussion of known technical obstacles and suggestions for further research.

A novel composite anode via immobilizing of Ce-doped PbO2 on CoTiO3 for efficiently electrocatalytic degradation of dye

The exploitation of efficient electrocatalyst is significantly important for degradation of refractory organic pollutants. Herein, a novel Ti/CoTiO₃/Ce-PbO₂ composite electrocatalyst (abbreviated as CTO/CP) is successfully constructed via facile consecutive immersion pyrolysis and electro-deposition method and then systematically characterized by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), Fourier Transform infrared spectroscopy (FT-IR), energy dispersive spectroscopy (EDS) and near infrared chemical imaging (NIR-CI). Importantly, the electrochemical measurements demonstrate that the CTO/CP possesses numerous prominent properties such as lower charge transfer resistance, larger electroactive area, higher oxygen evolution potential than those of the pristine Ti/CoTiO₃ (CTO) and Ti/Ce-PbO₂ (CP). Thereby, the CTO/CP exhibits an enhanced electrocatalytic degradation performance with the degradation efficiency as high as 90.0% and COD removal rate of 88.3% at 180 min for the optimal CTO/CP (denoted as 10 layers of CTO and 1 h electrodeposition of CP), in which the ·OH is the major reactive species. Additionally, the optimal CTO/CP also shows a higher ICE/ACE together with lower EEC and desirable stability, universal applicability for many different dyes and reusability. Overall, this work offers a promising approach for enhancing the electrocatalytic properties of CTO via introducing CP.