Enhancing the Textile Dye Removal from Aqueous Solution Using Cobalt Ferrite Nanoparticles Prepared in Presence of Fulvic Acid

New combined experimental and DFT studies for adsorption of sole Azo-dye or binary cationic dyes from aqueous solution

Textile-toxic synthetic dyes, which possess complex aromatic structures, are emitted into wastewater from various branches. To address this issue, the adsorption process was applied as an attractive method for the removal of dye contaminants from water in this article. An unprecedented integrated experimental study has been carried out, accompanied by theoretical simulations at the DFT-B3LYP/6-31G (d,P) level of theory to investigate how single Maxilon Blue GRL (MxB) dye or and its mixture with MG (Malachite Green) dyes interact with the adsorbent and compare the obtained results with the data obtained through experimentation. The full geometry optimization revealed the physical adsorption of dyes on the Al2O3 surface. Non-linear optical properties (NLO) results emphasized that the complex MG-Al2O3-MxB is a highly promising material in photo-applications, and the adsorbed binary system is energetically more favorable compared to the adsorbed sole dye system. The experimental results for (MxB) dye adsorption onto γ-Al2O3 affirmed that the optimum conditions to get more than 98% uptake were at dye concentration 100 ppm, pH 10, adsorbent content 0.05 g, and equilibrium time only 20 min. The kinetic and isothermal studies revealed that the adsorption accepted with the pseudo-second-order and Freundlich isotherm model, respectively. The removal efficiency of the mixture of MxB and MG dyes was the highest but did not change clearly with increasing the % of any of them. The details of the interaction mechanisms of the sole and binary dyes were proven.

Dye removal membrane from electrospun nanofibers of blended polybutylenesuccinate and sulphonated expanded polystyrene waste

Polystyrene (PS) is a thermoplastic polymer used in food packaging and the manufacture of trays and cups, among other applications. In this work, the preparation of a membrane by electrospinning blended sulphonated expanded PS waste and polybutylenesuccinate (PBS) is described. The fiber quality is controlled by selecting the right polymers' ratios and solvents. Investigation of the structure of the produced membranes by Fourier transform infrared spectroscopy-attenuated total reflectance confirmed the successful sulphonation of expanded PS and the appearance of characteristic (PBS) bands in the prepared blends. Morphology study of the electrospun membranes using a scanning electron microscope revealed that the quality of the fibers is improved significantly by increasing the amount of PBS in the blend solution. Moreover, continuous and more homogenous fibers are produced by increasing the ratio of PBS to 2%. The efficiency of the prepared membranes in dye removal was tested using methylene blue. The effects of different parameters such as, pH, contact time, temperature, and dye concentration have been studied. Also, kinetic and adsorption isotherm models as well as the durability of the prepared membranes were investigated. The membrane prepared from PSS/1% PBS demonstrated the highest dye uptake (846 mol) with good regeneration efficiency. The adsorption process was found to be endothermic and fits the Freundlich isotherm and pseudo-second-order kinetic model. The values of activation energy for the adsorption process are 36.98, 30.70, and 43.40 kJ/mol over PSS, PSS/1% PBS and PSS/2% PBS, respectively.

The pH dependent surface charging and points of zero charge. X. Update

Surfaces are often characterized by their points of zero charge (PZC) and isoelectric points (IEP). Different authors use these terms for different quantities, which may be equal to the actual PZC under certain conditions. Several popular methods lead to results which are inappropriately termed PZC. This present review is limited to zero-points obtained in the presence of inert electrolytes (halides, nitrates, and perchlorates of the 1st group metals). IEP are reported for all kinds of materials. PZC of metal oxides obtained as common intersection points of potentiometric curves for 3 or more ionic strengths (or by means of equivalent methods) are also reported, while the apparent PZC obtained by mass titration, pH-drift method, etc. are deliberately neglected. The results published in the recent publications and older results overlooked in the previous compilations by the same author are reported. The PZC/IEP are accompanied by information on the temperature and on the nature and concentration of supporting electrolyte (if available). The references to previous reviews by the same author allow to compare the newest results with the PZC/IEP of similar materials from the older literature.

Charge transport and heavy metal removal efficacy of graphitic carbon nitride doped with CeO2

Doping of graphitic carbon nitride (g-C₃N₄) with semiconductors prevents electron-hole recombination and enhances adsorption capacity. This work investigates the synthesis of a water remediation material using g-C₃N₄ doped with CeO₂ using two different techniques. The chemical structures of the doped g-C₃N₄ samples were confirmed using FTIR, XRD, XPS and their morphology was studied using SEM-EDX. Charge transport through the doped materials was illustrated by a comprehensive dielectric study using broadband spectroscopy. The ability of doped g-C₃N₄ to adsorb heavy metals was investigated thoroughly in the light of applying different parameters such as temperature, pH, time, and concentration. The results showed that the mode of doping of g-C₃N₄ by CeO₂ strongly affected its adsorption capacity. However, g-C₃N₄ doped with CeO₂ using the first mode adsorbed 998.4 mg g^-1 in case of Pb²⁺ and 448 for Cd²⁺. Kinetic study revealed that the adsorption process obeyed PSORE as its q ^exp _e is close to its q ^cal _e and the rate-controlling step involved coordination among the synthetic materials and the heavy metal ions. The recovery of Pb²⁺ and Cd²⁺ ions from various sorbents was investigated by utilizing different molar concentrations of HNO₃ and indicated no significant change in the sorption capability after three different runs. This study has demonstrated an efficient method to obtain a highly efficient adsorbent for removing heavy metals from waste water.

Highly enhanced dye adsorption of MoO3 nanoplates fabricated by hydrothermal-calcination approach in presence of chitosan and thiourea

Water pollution by organic dyes poses great challenge to the environment and living organism. Hence effective removal of organic dyes by cost effective methods have received significant attention in recent years. Herein, we report the complete removal of organic dyes (rhodamine B), methylene blue) and eosin yellow) from water via effective adsorption by MoO₃ catalyst. Hydrothermally synthesised MoO₂ (1) and amorphous MoS_x (2) using ammonium molybdate without and with thiourea exhibited low dye adsorption. In contrast, crystalline micro/nanoplates of MoO₃ (3 and 4) obtained from calcination of 1 and 2 showed highly enhanced dye adsorption. Particularly 4 showed higher dye adsorption compared to 3. UV-Visible absorption studies confirmed complete removal of organic dyes upon stirring with MoO₃ catalyst. Dye removal studies further revealed that cationic dyes are adsorbed faster than anionic dye that could be attributed to the surface charge of MoO₃. Interestingly, the adsorbed dyes were not released from MoO₃ for more than 50 days. The exhausted MoO₃ catalyst can be recovered by annealing at 400 °C. MoO₃ catalyst has also been used as packing materials in dropper column and demonstrated effective removal of dyes by passing through dyes separately as well as mixture.

Integrated experimental and theoretical insights for Malachite Green Dye adsorption from wastewater using low cost adsorbent

Water pollution is one of the problems that threaten humanity, and to confront it with only experimental procedures is not enough. It is necessary to integrate both practical methods and theoretical calculations to achieve decontamination with the most accurate interpretation. Hence, discussing the experimental mechanism study of Malachite Green (MG) dye adsorption with the help of the application of density functional theory (DFT) calculations is the main goal of this article. The experimental results affirmed that the preparation of γ-Al₂O₃ by precipitation method using (NH₄)₂CO₃ improved the porosity, the surface capability, and the adsorbent capacities (q_max = 210 mg/g) at optimum condition compared with the previous studies. Kinetic and equilibrium studies showed that the adsorption follows the pseudo-second-order model and Freundlich isotherm model, respectively. Also, the calculated and observed thermodynamic parameters exerted positive values of ΔH° and ΔS°, which translates into an endothermic process with increasing disorder of the system. Theoretical calculations at DFT- B3LYP/6-31G (d,P) level of theory were calculated to show the selectivity of using the cationic form of MG in the experimental measurements to find the interaction mechanism. The electronic structure and intramolecular charge transfer of MG, its cationic form and the complex of MG-Al were investigated theoretically at the B3LYP/6-31 G (d,p) level of theory. The equilibrium geometries of MG, its cationic form and the complex of MG-Al were determined, and it was found that these geometries are non-planar. The E_HOMO and E_LUMO energies can be used to calculate the global properties; chemical hardness (η), softness (S) and electronegativity (χ). The calculated non-linear optical parameters (NLO) of the studied compounds, the electronic dipole moment (μ), first-order hyperpolarizability (β), the hyper-Rayleigh scattering (β_HRS) and the depolarization ratio (DR), showed promising optical properties. Finally, the computational and the experimental results indicated that the adsorption efficiency of MG from wastewater was directly associated with the dye electrophilicity power.

Factors Affecting Synthetic Dye Adsorption; Desorption Studies: A Review of Results from the Last Five Years (2017-2021)

The primary, most obvious parameter indicating water quality is the color of the water. Not only can it be aesthetically disturbing, but it can also be an indicator of contamination. Clean, high-quality water is a valuable, essential asset. Of the available technologies for removing dyes, adsorption is the most used method due to its ease of use, cost-effectiveness, and high efficiency. The adsorption process is influenced by several parameters, which are the basis of all laboratories researching the optimum conditions. The main objective of this review is to provide up-to-date information on the most studied influencing factors. The effects of initial dye concentration, pH, adsorbent dosage, particle size and temperature are illustrated through examples from the last five years (2017-2021) of research. Moreover, general trends are drawn based on these findings. The removal time ranged from 5 min to 36 h (E = 100% was achieved within 5-60 min). In addition, nearly 80% efficiency can be achieved with just 0.05 g of adsorbent. It is important to reduce adsorbent particle size (with Φ decrease E = 8-99%). Among the dyes analyzed in this paper, Methylene Blue, Congo Red, Malachite Green, Crystal Violet were the most frequently studied. Our conclusions are based on previously published literature.