Thermorheological analysis of blend of high- and low-density polyethylenes

Modeling the Additive Effects of Nanoparticles and Polymers on Hydrogel Mechanical Properties Using Multifactor Analysis

Interpenetrating networks (IPN)s have been conceived as a biomimetic tool to tune hydrogel mechanical properties to the desired target formulations. In this study, the rheological behavior of acrylamide (AAm) [2.5-10%] hydrogels crosslinked with N,N'-methylenebis(acrylamide) (Bis) [0.0625-0.25%] was characterized in terms of the saturation modulus affected by the interaction of silica nanoparticle (SiNP) nanofillers [0-5%] and dextran [0-2%] at a frequency of 1 Hz and strain rate of 1% after a gelation period of 90 min. For single-network hydrogels, a prominent transition was observed at 0.125% Bis for 2.5% AAm and 0.25% Bis for 5% AAm across the SiNP concentrations and was validated by retrospective 3-level factorial design models, as characterized by deviation from linearity in the saturation region (R² = 0.86). IPN hydrogels resulting from the addition of dextran to the single network in the pre-saturation region, as outlined by the strong goodness of fit (R²= 0.99), exhibited a correlated increase in the elastic (G') and viscous moduli (G"). While increasing the dextran concentrations [0-2%] and MW [100 kDa and 500 kDa] regulated the increase in G', saturation in G" or the loss tangent (tan(δ)) was not recorded within the observed operating windows. Results of multifactor analysis conducted on Han plots in terms of the elastic gains indicate that amongst the factors modulating the viscoelasticity of the IPN hydrogels, dextran concentration is the most important (R_Dex = 35.3 dB), followed by nanoparticle concentration (R_SiNP = 7.7 dB) and dextran molecular weight (R_MW = 2.9 dB). The results demonstrate how the Han plot may be systematically used to quantify the main effects of intensive thermodynamic properties on rheological phase transition in interpenetrating networks where traditional multifactor analyses cannot resolve statistical significance.

Rheological Behavior of Blends of Metallocene Catalyzed Long-Chain Branched Polyethylenes. Part I: Shear Rheological and Thermorheological Behavior

Long-chain branched metallocene-catalyzed high-density polyethylenes (LCB-mHDPE) were solution blended to obtain blends with varying degrees of branching. A high molecular LCB-mHDPE was mixed with low molecular LCB-mHDPE at varying concentrations. The rheological behavior of those low molecular LCB-mHDPE is similar but their molar mass and molar mass distribution are significantly different. Those blends were characterized rheologically to study the effects of concentration, molar mass distribution, and long-chain branching level of the low molecular LCB-mHDPE. Owing to the ultra-long relaxation times of the high molecular LCB-mHDPE, the blends exhibited a clearly more long-chain branched behavior than the base materials. The thermorheological complexity analysis showed an apparent increase in the activation energies E_a determined from G′, G″, and especially δ. E_a(δ), which for LCB-mHDPE is a peak function, turned out to produce even more pronounced peaks than observed for LCB-mPE with narrow molar mass distribution and also LCB-mPE with broader molar mass distribution. Thus, it is possible to estimate the molar mass distribution from the details of the thermorheological complexity.

Filament Extrusion and Its 3D Printing of Poly(Lactic Acid)/Poly(Styrene-co-Methyl Methacrylate) Blends

Herein, we report the melt blending of amorphous poly(lactide acid) (PLA) with poly(styrene-co-methyl methacrylate) (poly(S-co-MMA)). The PLAx/poly(S-co-MMA)y blends were made using amorphous PLA compositions from 50, 75, and 90wt.%, namely PLA50/poly(S-co-MMA)50, PLA75/poly(S-co-MMA)25, and PLA90/poly(S-co-MMA)10, respectively. The PLAx/poly(S-co-MMA)y blend pellets were extruded into filaments through a prototype extruder at 195 °C. The 3D printing was done via fused deposition modeling (FDM) at the same temperature and a 40 mm/s feed rate. Furthermore, thermogravimetric curves of the PLAx/poly(S-co-MMA)y blends showed slight thermal decomposition with less than 0.2% mass loss during filament extrusion and 3D printing. However, the thermal decomposition of the blends is lower when compared to amorphous PLA and poly(S-co-MMA). On the contrary, the PLAx/poly(S-co-MMA)y blend has a higher Young’s modulus (E) than amorphous PLA, and is closer to poly(S-co-MMA), in particular, PLA90/poly(S-co-MMA)10. The PLAx/poly(S-co-MMA)y blends proved improved properties concerning amorphous PLA through mechanical and rheological characterization.