Graphene oxide reinforced polyvinyl alcohol/polyethylene glycol blend composites as high-performance dielectric material

PLGA-PVA-PEG Single Emulsion Method as a Candidate for Aminolevulinic Acid (5-ALA) Encapsulation: Laboratory Scaling up and Stability Evaluation

One of the most widely used molecules used for photodynamic therapy (PDT) is 5-aminolevulinic acid (5-ALA), a precursor in the synthesis of tetrapyrroles such as chlorophyll and heme. The 5-ALA skin permeation is considerably reduced due to its hydrophilic characteristics, decreasing its local bioavailability and therapeutic effect. For this reason, five different systems containing polymeric particles of poly [D, L–lactic–co–glycolic acid (PLGA)] were developed to encapsulate 5-ALA based on single and double emulsions methodology. All systems were standardized (according to the volume of reagents and mass of pharmaceutical ingredients) and compared in terms of laboratory scaling up, particle formation and stability over time. UV-VIS spectroscopy revealed that particle absorption/adsorption of 5-ALA was dependent on the method of synthesis. Different size distribution was observed by DLS and NTA techniques, revealing that 5-ALA increased the particle size. The contact angle evaluation showed that the system hydrophobicity was dependent on the surfactant and the 5-ALA contribution. The FTIR results indicated that the type of emulsion influenced the particle formation, as well as allowing PEG functionalization and interaction with 5-ALA. According to the ¹H-NMR results, the 5-ALA reduced the T1 values of polyvinyl alcohol (PVA) and PLGA in the double emulsion systems due to the decrease in molecular packing in the hydrophobic region. The results indicated that the system formed by single emulsion containing the combination PVA–PEG presented greater stability with less influence from 5-ALA. This system is a promising candidate to successfully encapsulate 5-ALA and achieve good performance and specificity for in vitro skin cancer treatment.

Graphene Oxide/Polyvinyl Alcohol–Formaldehyde Composite Loaded by Pb Ions: Structure and Electrochemical Performance

An immobilization of graphene oxide (GO) into a matrix of polyvinyl formaldehyde (PVF) foam as an eco-friendly, low cost, superior, and easily recovered sorbent of Pb ions from an aqueous solution is described. The relationships between the structure and electrochemical properties of PVF/GO composite with implanted Pb ions are discussed for the first time. The number of alcohol groups decreased by 41% and 63% for PVF/GO and the PVF/GO/Pb composite, respectively, compared to pure PVF. This means that chemical bonds are formed between the Pb ions and the PVF/GO composite based on the OH groups. This bond formation causes an increase in the T_g values attributed to the formation of a strong surface complexation between adjacent layers of PVF/GO composite. The conductivity increases by about 2.8 orders of magnitude compared to the values of the PVF/GO/Pb composite compared to the PVF. This means the presence of Pb ions is the main factor for enhancing the conductivity where the conduction mechanism is changed from ionic for PVF to electronic conduction for PVF/GO and PVF/GO/Pb.

Highly Skin-Compliant Polymeric Electrodes with Synergistically Boosted Conductivity toward Wearable Health Monitoring

Despite rapid advances in stretchable electrodes, successful examples of polymeric dry electrodes are limited. Especially in wearable health monitoring, it is urgent to develop biocompatible electrodes that possess intrinsic skin-compliance while maintaining a high conductivity. Herein, a strategy is demonstrated to synergistically regulate the interpenetration behavior and molecular crystallinity in the blend via embedding a novel double network, i.e. physically cross-linked poly(vinyl alcohol) (PVA) and covalently cross-linked polyethylene glycol diacrylate (PEGDA), into the PEDOT:PSS matrix. The favorable interaction energy between PVA and PEGDA enables well-distributed microstructure with finer phase separation in the film, affording a low Young's modulus of 16 MPa with a high conductivity of 442 S/cm. Consequently, the optimal polymeric electrode can acquire high-quality electromyogram (EMG) and electrocardiogram (ECG) signals. Our results provide a feasible approach for producing skin-compliant polymeric electrodes toward next-generation health monitors.

Ionic liquid dispersed highly conducting polymer electrolyte for supercapacitor application: Current scenario and prospects “ICSEM 2021”

Ionic liquid (IL) is now being considered as a novel contender in the development of highly conducting polymer electrolytes rather than a solvent. It has a significant impact on the electrochemical performance of polymer electrolytes. This study emphasizes the significance of low viscosity IL dispersion within a polymer (PVA) matrix. The electrical, structural and photoelectrochemical properties of the IL-doped polymer electrolyte are discussed in detail. These highly conducting IL doped solid polymer electrolytes show promise towards the development of highly efficient Supercapacitors.

Khalil A, M. Azzouz I. Graphene Functionalization towards Developing Superior Supercapacitors Performance

Graphene is known as the miracle material of the 21st century for the wide band of participating applications and epic properties. Unlike the CVD monolayer graphene, Reduced graphene oxide (RGO) is a commercial form with mass production accessibility via numerous numbers of methods in preparation and reduction terms. Such RGO form showed exceptional combability in supercapacitors (SCs) where RGO is participated to promote flexibility, lifetime and performance. The chapter will illustrate 4 critical milestones of using graphene derivatives for achieving SC’s superior performance. The first is using oxidized graphene (GO) blind with polymer for super dielectric spacer. The other three types are dealing with electrolytic SCs based on RGO. Polyaniline (PANI) was grown on GO for exceptionally stable SCs of 100% retention. Silver decoration of RGO was used for all-solid-state printable device. The solid-state gel electrolyte was developed by adding GO to promote current rating. Finally, laser reduced graphene is presented as a one-step and versatile technique for micropatterning processing. The RGO reduction was demonstrated from a laser GO interaction perspective according to two selected key parameters; wavelength and pulse duration.

Design of Promising Green Cation-Exchange-Membranes-Based Sulfonated PVA and Doped with Nano Sulfated Zirconia for Direct Borohydride Fuel Cells

The direct borohydride fuel cell (DBFC) is a low-temperature fuel cell that requires the development of affordable price and efficient proton exchange membranes for commercial purposes. In this context, super-acidic sulfated zirconia (SO₄ZrO₂) was embedded into a cheap and environmentally friendly binary polymer blend, developed from poly(vinyl alcohol) (PVA) and iota carrageenan (IC). The percentage of SO₄ZrO₂ ranged between 1 and 7.5 wt.% in the polymeric matrix. The study findings revealed that the composite membranes’ physicochemical features improved by adding increasing amounts of SO₄ZrO₂. In addition, there was a decrease in the permeability and swelling ratio of the borohydride membranes as the SO₄ZrO₂ weight% increased. Interestingly, the power density increased to 76 mW cm⁻² at 150 mA cm⁻², with 7.5 wt.% SO₄ZrO_2, which is very close to that of Nafion117 (91 mW cm⁻²). This apparent selectivity, combined with the low cost of the eco-friendly fabricated membranes, points out that DBFC has promising future applications.

Slow-release lubrication of artificial joints using self-healing polyvinyl alcohol/polyethylene glycol/ graphene oxide hydrogel

New fabrication methods and lubrication materials must be developed to improve the lubrication performance of artificial joints and increase the lubrication duration. Herein, a novel polyvinyl alcohol/polyethylene glycol/graphene oxide (PVA/PEG/GO) hydrogel was prepared by a physical cross-linking method, and then the hydrogel and its sustained-release solution were used as lubricant for friction evaluation. The results demonstrated that the slow-release gel solution has good lubrication performance, and coefficient of friction (COF) is only 0.04, which is much lower than the COF of distilled water (about 0.08) under the same conditions. The structure characterization results revealed that no new materials are formed in the gel. The results of thermogravimetric analyses and differential scanning calorimetry demonstrated that the addition of GO may improve the network crosslinking structure of the PVA/PEG hydrogel and improve its mechanical strength. In addition, PVA/PEG/GO hydrogel has superior self-healing function. The self-healing hydrogel did not break again after being pulled under 200 G of weights. The PVA/PEG/GO hydrogel with excellent slow-release lubricating performance and self-healing properties provides a novel candidate for design of long-term lubricating artificial joints, and is expected to promote the progress of artificial joint lubrication applications.

Organic-Inorganic Novel Green Cation Exchange Membranes for Direct Methanol Fuel Cells

Commercializing direct methanol fuel cells (DMFC) demands cost-effective cation exchange membranes. Herein, a polymeric blend is prepared from low-cost and eco-friendly polymers (i.e., iota carrageenan (IC) and polyvinyl alcohol (PVA)). Zirconium phosphate (ZrPO4) was prepared from the impregnation–calcination method and characterized by energy dispersive X-ray analysis (EDX map), X-ray diffraction analysis (XRD), Fourier transform infrared spectroscopy (FTIR), and transmission electron microscopy (TEM), then incorporated as a bonding and doping agent into the polymer blend with different concentrations. The new fabricated membranes were characterized by SEM, FTIR, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and XRD. The results revealed that the membranes’ physicochemical properties (oxidative stability, tensile strength) are enhanced with increasing doping addition, and they realized higher results than Nafion 117 because of increasing numbers of hydrogen bonds fabricated between the polymers and zirconium phosphate. Additionally, the methanol permeability was decreased in the membranes with increasing zirconium phosphate content. The optimum membrane with IC/SPVA/ZrPO4-7.5 provided higher selectivity than Nafion 117. Therefore, it can be an effective cation exchange membrane for DMFCs applications.

Titanium dioxide (TiO2) nanoparticles reinforced polyvinyl formal (PVF) nanocomposites as chemiresistive gas sensor for sulfur dioxide (SO2) monitoring

The present work reports the preparation of polyvinyl formal (PVF)/Titanium dioxide (TiO₂) nanocomposite films using a solution casting method followed by the characterization of the synthesized PVF/TiO₂ nanocomposite films using various analytical techniques namely FTIR, XRD, UV-vis, SEM and TGA analysis. The results obtained from different analyses confirmed that the TiO₂ NPs was fine dispersed within the PVF matrix and there exists well compatibility among the polymer matrix and the nanofiller. The pristine TiO₂ NPs based fabricated chemiresistive sensor exhibits the maximum sensitivity of 50.25% at 370 °C where as PVF/TiO₂ nanocomposite sensor showed the enhanced sensitivity of 83.75% at a relatively low operating temperature of 150 °C towards 600 ppm sulfur dioxide (SO₂) gas. The 25 wt% PVF/TiO₂ nanocomposite film sensor exhibited good sensitivity (∼83.75%), selectivity, rapid response time (66 s)/recovery time (107 s), and long-term stability of 60 days for SO₂ gas detection. The fabricated PVF/TiO₂ nanocomposite film sensors in our work possesses the advantages of low power consumption, cost-effective, and distinguished sensing abilities for SO₂ detection makes it possible for potential applications. Thus, the fabricated chemiresistive sensors based on TiO₂ NPs reinforced PVF nanocomposites films are evaluated and experimental results to show an excellent behavior towards SO₂ gas detection for industrial processes control and environmental monitoring applications.

Novel Crosslinked Sulfonated PVA/PEO Doped with Phosphated Titanium Oxide Nanotubes as Effective Green Cation Exchange Membrane for Direct Borohydride Fuel Cells

A direct borohydride fuel cell (DBFC) is a type of low temperature fuel cell which requires efficient and low cost proton exchange membranes in order to commercialize it. Herein, a binary polymer blend was formulated from inexpensive and ecofriendly polymers, namely polyethylene oxide (PEO) and poly vinyl alcohol (PVA). Phosphated titanium oxide nanotube (PO₄TiO₂) was synthesized from a simple impregnation-calcination method and later embedded for the first time as a doping agent into this polymeric matrix with a percentage of 1-3 wt%. The membranes' physicochemical properties such as oxidative stability and tensile strength were enhanced with increasing doping addition, while the borohydride permeability, water uptake, and swelling ratio of the membranes decreased with increasing PO₄TiO₂ weight percentage. However, the ionic conductivity and power density increased to 28 mS cm^-1 and 72 mWcm^-2 respectively for the membrane with 3 wt% of PO₄TiO₂ which achieved approximately 99% oxidative stability and 40.3 MPa tensile strength, better than Nafion117 (92% RW and 25 MPa). The fabricated membrane with the optimum properties (PVA/PEO/PO₄TiO₂-3) achieved higher selectivity than Nafion117 and could be efficient as a proton exchange membrane in the development of green and low cost DBFCs.

Studying some Optical Properties of Polyethylene Glycol Doped with Al- Nanoparticles

This research aims to improve some optical properties of polyethylene glycol (PEG) by adding different weight percentages of aluminium nanoparticles )0, 2, 4, 6 and 8) % and for achieving a new composite material with improved characteristics. nanocomposite thin films were prepared by solution casting method with different weight percentages of Al nanoparticles. The samples were characterized by X-ray diffraction (XRD), FTIR and UV-visible spectrophotometer. FTIR-spectra of (PEG-Al) nanocomposite show various special bands of bending for groups (C=O, C–O, C–H, C-N, C-I). Optical microscopy images illustrate the morphology of surface for (PEG) composite. The optical properties measurement by using (UV–VIS) spectrophotometer at wavelength range )220 – 1100(nm were determined. Results show that the absorbance spectrum increased with increase the weight percentages of Al-nanoparticles and the values of absorption coefficient have increased as well as refractive index values increased with the addition of aluminium nanoparticle

Rheological and Dielectric Behavior of 3D-Printable Chitosan/Graphene Oxide Hydrogels

The effect of concentration, temperature, and the addition of graphene oxide (GO) nanosheets on the rheological and dielectric behavior of chitosan (CS) solutions, which influences the formation of the blend materials for various applications including 3D printing and packaging, was studied. Among tested acid solutions, the rheological behavior of 1% CS in acetic and lactic acid solutions was found to be similar, whereas the hydrochloric acid solution showed an abnormal drop in the dynamic moduli. Oscillatory rheology confirmed a distinct gel point for the CS solutions at below 10 °C. Both the G' and G″ of the solutions increased with the loading concentrations of GO between 0.5 and 1%, and it marginally dropped at the loading concentration of 2%, which is consistent with AFM observation. The steady-shear flow data fitted the Carreau model. Dielectric property measurement further confirmed that both the dielectric constant, ε' and the loss factor, ε″ for the CS in hydrochloric acid solutions behaved differently from others. Addition of GO significantly improved both ε' and ε″, indicating an improvement in the dielectric properties of CS/GO solutions. The dispersion of GO into the CS matrix was assessed by measuring XRD, FTIR, and microscopy of the film prepared from the solutions. Furthermore, the inclusion of GO into CS solution containing pluronic F127 (F127) base for potential 3D printing application showed positive results in terms of the printing accuracy and shape fidelity of the printed objects (films and scaffolds). The optimized composition with homogeneous particle distribution indicated that up to ∼50 mg/mL GO concentration (w/v of F127 base) was suitable to print both films and scaffolds for potential biomedical applications.

Achieving high-performance epoxy nanocomposites with trifunctional poly(oxypropylene)amines functionalized graphene oxide

In this article, two types of functional graphene oxide (GO) with amine-rich surface were synthesized through chemically grafting two different molecular chain length trifunctional poly(oxypropylene)amines T5000 and T403, which were named as T5000-GO and T403-GO, respectively. The functionalized GO was then added to epoxy (EP) resin. Fourier transform infrared spectra analysis confirmed successful chemical functionalization on GO. Both T403-GO and T5000-GO were tightly embedded in the EP, because the amine-rich surface of functionalized-GO could form covalent bonds with the EP matrix, thereby contributing to the enhancement of mechanical properties. Particularly, T5000-GO, which has longer grafting molecule chains, achieved better compatibility and dispersibility in the EP matrix, resulting in a better reinforcing efficiency in mechanical properties. For example, the T5000-GO/EP composites showed an incremental enhancement in tensile strength with increasing filler concentrations, whereas their T403-GO/EP counterparts failed to follow the same trend. Meanwhile, the T5000-GO/EP composites with only 0.1-wt% T5000-GO achieved a prominent increase in flexural strength (approximately 50%) and flexural modulus (approximately 26.8%), which were higher than those of T403-GO-filled counterparts. This work indicated that the compatibility and interphase between GO and EP could be designed by manipulating the length of grafting molecule chains, thereby providing a better understanding of the relationship between the structure and mechanical properties of the graphene/EP nanocomposites.

Synthesis, optimization and applications of ZnO/polymer nanocomposites

Polymer composites have established an excellent position among the technologically essential materials because of their wide range of applications. An enormous research interest has been devoted to zinc oxide (ZnO) based polymer nanocomposites, due to their exceptional electrical, optical, thermal, mechanical, catalytic, and biomedical properties. This article provides a review of various polymer composites consisting of ZnO nanoparticles (NPs) as reinforcements, exhibiting excellent properties for applications such as the dielectric, sensing, piezoelectric, electromagnetic shielding, thermal conductivity and energy storage. The preparation methods of such composites including solution blending, in situ polymerization, and melt intercalation are also explained. The current challenges and potential applications of these composites are provided in order to guide future progress on the development of more promising materials. Finally, a detailed summary of the current trends in the field is presented to progressively show the future prospects for the development of ZnO containing polymer nanocomposite materials.

Preparation of Miscible PVA/PEG Blends and Effect of Graphene Concentration on Thermal, Crystallization, Morphological, and Mechanical Properties of PVA/PEG (10 wt%) Blend

Water-soluble polymers such as poly(vinyl alcohol) (PVA) and poly(ethylene glycol) (PEG) and their nanocomposites with graphene were prepared by using a solution mixing and casting technique. The effect of different PEG loadings was investigated to determine the optimum blend ratio. The films were characterized using Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), and thermogravimetric analyzer (TGA) methods. Also, the mechanical properties including tensile strength and elongation at break were measured using a universal tensile testing machine. FTIR results confirmed the formation of the H-bond between PEG and PVA. DSC studies revealed that PEG has a significant plasticization effect on PVA as seen by the drop in the glass transition temperature (Tg). The blend with 10 wt% PEG loading was found to be the optimum blend because of good compatibility as shown by FTIR and SEM results and improved thermal properties. PVA/PEG (10%) nanocomposites were prepared using graphene as a nanofiller. It was found that the elongation at break increased by 62% from 147% for the PVA/PEG (10%) blend to 209% for the nanocomposite with graphene loading of 0.2 wt%. The experimental values of tensile strength were compared using the predictive model of Nicolais and Narkis.

Synthesis and properties of polyimide nanocomposite containing dopamine-modified graphene oxide

Polyimide (PI)/graphene oxide (GO) nanocomposites with different loads of polydopamine-modified graphene oxide (PI/PDA-GO) were prepared. Meanwhile, the as-prepared PI/PDA-GO nanocomposites were compared with pure PI in terms of their morphologies, thermal and mechanical properties. Only a minor mass fraction of PDA-GO was required to enhance the mechanical and thermal properties of PI. The tensile strength of 1 wt% PDA-GO/PI was increased by 12% and the tensile modulus of 1 wt% PDA-GO/PI nanocomposites was increased by 25% compared to those of pure PI. Vickers hardness of the PI hybrid films increased with PDA-GO load and the maximum enhancement in Vickers hardness was observed at 2 wt% PDA-GO loading. On the other hand, the storage modulus of 1 wt% PDA-GO/PI was increased by 54% than that of neat PI. In consideration of the facile preparation of PDA-coated GO, superior physical properties over neat PI, PI/PDA-GO nanocomposites showed promising applications as functional films or composites.

Studies on the Electrical Properties of Graphene Oxide-Reinforced Poly (4-Styrene Sulfonic Acid) and Polyvinyl Alcohol Blend Composites

In the present study, graphene oxide (GO)-reinforced poly (4-styrenesulfonic acid) (PSSA)/polyvinyl alcohol (PVA) blend composite films were prepared using colloidal blending technique at various concentrations of GO (0–3[Formula: see text]wt.%). The morphological investigations of the prepared composites were carried out using polarized optical microscopy and scanning electron microscopy. The electrical properties of composites were evaluated using an impedance analyzer in the frequency range 50[Formula: see text]Hz to 20[Formula: see text]MHz and temperature in the range 40–150[Formula: see text]C. Morphological studies infer that GO was homogeneously dispersed in the PSSA/PVA blend matrix. Investigations of electrical property indicate that the incorporation of GO into PSSA/PVA blend matrix resulted in the enhancement of the impedance ([Formula: see text] and the quality factor ([Formula: see text]-factor) values. A maximum impedance of about 4.32[Formula: see text][Formula: see text][Formula: see text]10[Formula: see text] was observed at 50[Formula: see text]Hz and 90[Formula: see text]C for PSSA/PVA/GO composites with 3[Formula: see text]wt.% GO loading. The [Formula: see text]-factor also increased from 8.37 for PSSA/PVA blend to 59.8 for PSSA/PVA/GO composites with 3[Formula: see text]wt.% GO loading. These results indicate that PSSA/PVA/GO composites can be used for high-[Formula: see text] capacitor applications.