Evaluating radiation risks and resource opportunities associated with phosphogypsum in the Philippines

Staged purification of phosphogypsum using pH-dependent separation process

Phosphogypsum (PG) is an industrial by-product of the transformation of phosphate rocks. For decades, PG has been a source of environmental concern due to the massive amount produced thus far, i.e., 7 billion tons, with a current production rate of 200-280 million tons per year. Phosphate minerals contain various impurities that precipitate and concentrate within PG. These impurities hinder PG usability in various sectors. This paper aims to purify PG using an innovative process based on staged valorization of PG. Initially, PG dissociation by ethylenediaminetetraacetic acid (EDTA) was optimized. After screening of different parameters and monitoring the ionic conductivity of solutions, it was disclosed that a pH-dependent solubilization process in the presence of EDTA resulted in high solubility of PG, up to 11.82 g/100 mL at pH > 11. Subsequently, a recovery of the purified PG by selective precipitation of calcium sulfate dihydrate (CSD) from obtained filtrate through pH adjustment to 3.5 were investigated. An abatement of 99.34% Cr, 97.15% Cd, 95.73% P2O5, 92.75% Cu, 92.38% Al2O3, 91.16% Ni, 74.58% Zn, 72.75% F, 61.43% MgO, 58.8% Fe2O3, 56.97% K2O, and 55.41% Ba was achieved. The process relied on the variation of EDTA chelation properties towards monovalent, divalent, and trivalent cations at different pHs. According to the findings of this study, a staged purification process in the presence of EDTA is an effective method for removing impurities from the industrial PG.

The Release of Pollutants through the Bleeding of Cemented Phosphogypsum Backfill: Link to Protocols for Slurry Preparation

The present study investigated the effects of protocols for slurry preparation on the release of pollutants into bleeding water from cemented phosphogypsum (PG) backfill. Backfill slurry was prepared using four different protocols in which different parameters varied, including binder/PG ratio, solid concentration, binder type and mixing procedure. The concentrations of phosphate, fluoride and sulfate and the pH values of the obtained bleeding water were measured. The results demonstrated that the slurry preparation protocols affected the quantities of pollutants through the concentrations of pollutants in bleeding water and the bleeding rate. On the one hand, the binder/PG ratio was the key factor influencing the concentrations of all pollutants in bleeding water. Comparatively speaking, the binder type and mixing procedure had an obvious influence on the fluoride concentration but had little influence on the phosphate and sulfate concentrations in the bleeding water. On the other hand, the protocols for slurry preparation affected the bleeding rate by determining the water retention and water content of the backfill slurry. The most effective protocol for slurry preparation for cemented PG backfill could reduce the bleeding rate and enhance the immobilization of pollutants, minimizing the phosphate concentration in bleeding water to below 0.2 mg/L. However, it appeared that the fluoride concentration was still tens of milligrams per liter (over the limit of 10 ten milligrams per liter), to which attention should be paid.

Better filterability and reduced radioactivity of phosphogypsum during phosphoric acid production in Morocco using a fly ash waste and pure silica additive

Reactive silica additives, such as clays, can increase the filterability of phosphogypsum (PG) during wet phosphoric acid production from phosphate rock (PR). In this study, the effect of adding inexpensive fly ash waste (34 kg per t PR) together with lower quantities of pure silica (8.5 kg per t PR) on the radioactivity of PG was investigated. The addition of fly ash waste/pure silica reduced the radiological activity of the PG by roughly 30%. The reduction was attributed to decreased activities from 238U (60% reduction) and 226Ra (30% reduction) in PG. Besides, P2O5 losses were slightly decreased.