Environmentally Benign Oxidation of Alkylphenols to p-Benzoquinones: A Comparative Study of Various Ti-Containing Catalysts

Building Porous Ni(Salen)-Based Catalysts from Waste Styrofoam via Autocatalytic Coupling Chemistry for Heterogeneous Oxidation with Molecular Oxygen

The development of robust and industrially viable catalysts from plastic waste is of great significance, and the facile construction of high performance heterogeneous catalyst systems for phenol-quinone conversions remains a grand challenge. Herein, a feasible strategy is demonstrated to reclaim Styrofoam into hierarchically porous nickel-salen-loaded hypercrosslinked polystyrene (PS@Ni-salen) catalysts with high activities through an unusual autocatalytic coupling route. The salen is immobilized onto PS chain by Friedel-Crafts alkylation of benzyl chloride derivatives, and the generated hydrogen chloride coordinately promotes the simultaneous crosslinking and bridge formation between aromatic rings via a Scholl coupling route, leading to hierarchically porous networks. After the metallization with Ni, the resultant networks exhibit high catalytic activity for the oxidation of 2,3,6-trimethylphenol to 2,3,5-trimethyl-1,4-benzoquinone under mild conditions (303 K, 1 bar of O2 ). This catalyst also demonstrates attractive recycling performance without an obvious loss of catalytic efficiency over five consecutive cycles. This methodology might provide a potential sustainable alternative to construct environmentally benign and cost-effective catalysts for specific organic transformation.

Metal-Organic Frameworks in Oxidation Catalysis with Hydrogen Peroxide

In recent years, metal–organic frameworks (MOFs) have received increasing attention as selective oxidation catalysts and supports for their construction. In this short review paper, we survey recent findings concerning use of MOFs in heterogeneous liquid-phase selective oxidation catalysis with the green oxidant–aqueous hydrogen peroxide. MOFs having outstanding thermal and chemical stability, such as Cr(III)-based MIL-101, Ti(IV)-based MIL-125, Zr(IV)-based UiO-66(67), Zn(II)-based ZIF-8, and some others, will be in the main focus of this work. The effects of the metal nature and MOF structure on catalytic activity and oxidation selectivity are analyzed and the mechanisms of hydrogen peroxide activation are discussed. In some cases, we also make an attempt to analyze relationships between liquid-phase adsorption properties of MOFs and peculiarities of their catalytic performance. Attempts of using MOFs as supports for construction of single-site catalysts through their modification with heterometals will be also addressed in relation to the use of such catalysts for activation of H2O2. Special attention is given to the critical issues of catalyst stability and reusability. The scope and limitations of MOF catalysts in H2O2-based selective oxidation are discussed.

Cyclohexene Oxidation with H2O2 over Metal-Organic Framework MIL-125(Ti): The Effect of Protons on Reactivity

The catalytic performance of the titanium-based metal–organic framework MIL-125 was evaluated in the selective oxidation of cyclohexene (CyH) with environmentally friendly oxidants, H2O2 and tBuOOH. The catalytic activity of MIL-125 as well as the oxidant utilization efficiency and selectivity toward epoxide and epoxide-derived products can be greatly improved by acid additives (HClO4 or CF3SO3H). In the presence of 1 molar equivalent (relative to Ti) of a proton source, the total selectivity toward CyH epoxide and trans-cyclohexane-1,2-diol reached 75–80% at 38–43% alkene conversion after 45 min of reaction with 1 equivalent of 30% H2O2 at 50 °C. With 50% H2O2 as the oxidant, the total selectivity toward heterolytic oxidation products increased up to 92% at the same level of alkene conversion. N2 adsorption, powder X-ray diffraction (PXRD), and infrared (IR) spectroscopy studies before and after the catalytic oxidations confirmed the absence of structural changes in the Metal–organic framework (MOF) structure. MIL-125 was stable toward titanium leaching, behaved as a truly heterogeneous catalyst, and could easily be recovered and reused several times without any loss of the catalytic properties.

Surface organometallic chemistry in heterogeneous catalysis

Surface organometallic chemistry has been reviewed with a special focus on environmentally relevant transformations (C–H activation, CO₂conversion, oxidation).

A porous carbon derived from amino-functionalized material of Institut Lavoisier as a solid-phase microextraction fiber coating for the extraction of phthalate esters from tea

In this work, a porous carbon derived from amino-functionalized material of Institut Lavoisier (C-NH2 -MIL-125) was prepared and coated onto a stainless-steel wire through sol-gel technique. The coated fiber was used for the solid-phase microextraction of trace levels of phthalate esters (diallyl phthalate, di-iso-butyl ortho-phthalate, di-n-butyl ortho-phthalate, benzyl-n-butyl ortho-phthalate, and bis(2-ethylhexy) ortho-phthalate) from tea beverage samples before gas chromatography with mass spectrometric analysis. Several experimental parameters that could influence the extraction efficiency such as extraction time, extraction temperature, sample pH, sample salinity, stirring rate, desorption temperature and desorption time, were investigated. Under the optimal conditions, the linearity existed in the range of 0.05-30.00 μg/L for green jasmine tea beverage samples, and 0.10-30.00 μg/L for honey jasmine tea beverage samples, with the correlation coefficients (r) ranging from 0.9939 to 0.9981. The limits of detection of the analytes for the method were 2.0-3.0 ng/L for green jasmine tea beverage sample, and 4.0-5.0 ng/L for honey jasmine tea beverage sample, depending on the compounds. The recoveries of the analytes for the spiked samples were in the range of 82.0-106.0%, and the precision, expressed as the relative standard deviations, was less than 11.1%.