Preparation and application of magnetic nitrogen-doped rGO for persulfate activation

Application of Functional Modification of Iron-Based Materials in Advanced Oxidation Processes (AOPs)

Advanced oxidation processes (AOPs) have become a favored approach in wastewater treatment due to the high efficiency and diverse catalyzed ways. Iron-based materials were the commonly used catalyst due to their environmental friendliness and sustainability in the environment. We collected the published papers relative to the application of the modified iron-based materials in AOPs between 1999 and 2020 to comprehensively understand the related mechanism of modified materials to improve the catalytic performance of iron-based materials in AOPs. Related data of iron-based materials, modification types, target pollutants, final removal efficiencies, and rate constants were extracted to reveal the critical process of improving the catalytic efficiency of iron-based materials in AOPs. Our results indicated that the modified materials through various mechanisms to enhance the catalytic performance of iron-based materials. The principal aim of iron-based materials modification in AOPs is to increase the content of available Fe2+ and enhance the stability of Fe2+ in the system. The available Fe2+ is elevated by the following mechanisms: (1) modified materials accelerate the electron transfer to promote the Fe3+/Fe2+ reaction cycle in the system; (2) modified materials form chelates with iron ions and bond with iron ions to avoid Fe3+ precipitation. We further analyzed the effect of different modifying materials in improving these two mechanisms. Combining the advantages of different modified materials to develop iron-based materials with composite modification methods can enhance the catalytic performance of iron-based materials in AOPs for further application in wastewater treatment.

Visible light-activated self-powered photoelectrochemical aptasensor for ultrasensitive chloramphenicol detection based on DFT-proved Z-scheme Ag2CrO4/g-C3N4/graphene oxide

A visible light self-powered photoelectrochemical (PEC) aptasensor based on silver chromate particles, graphitic carbon nitride nanosheets and graphene oxide sheets (Ag₂CrO₄/g-C₃N₄/GO) for the ultrasensitive detection of chloramphenicol (CAP) was reported in this work. g-C₃N₄ was considered to be the fundamental photoelectric material because of its great oxidation ability of photogenerated hole as well as excellent biocompatibility and low toxicity. However, the narrow light absorption range and rapid carrier recombination rate limit the application of pure g-C₃N₄. Herein, Ag₂CrO₄ and GO as photosensitizer were introduced to improve the photoelectric properties of g-C₃N₄. The photocurrent of the developed ternary composite was about 3 times higher than that of pristine g-C₃N₄, which proves it can be used as a suitable photoelectric active material. Moreover, the mechanism of Z-scheme electron transfer path was proved by density functional theory (DFT) calculation. The fabricated PEC aptasensor exhibited high sensitivity toward CAP with a wide liner response of 0.5 pM to 50 nM and a detection limit of 0.29 pM. The specific recognition mechanism and excellent sensing performance indicated this aptasensor could serve as a useful tool for selective and ultrasensitive CAP detection in practical analysis.

Activation of persulfate by heterogeneous catalyst ZnCo2O4–RGO for efficient degradation of bisphenol A

A nanocomposite, reduced graphene oxide (RGO) modified ZnCo2O4 (ZnCo2O4–RGO) was synthesized via one-step solvothermal method for activating persulfate (PS) to degrade bisphenol A (BPA). The morphology and structure of the nanocomposite were identified by X-ray diffraction, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy, and transmission electron microscopy. RGO provides nucleation sites for ZnCo2O4 to grow and inhibits the agglomeration of the nanoparticles. The influence of different reaction conditions on the oxidation of BPA catalyzed by ZnCo2O4–RGO was investigated, including the content of RGO, the dosage of catalyst, the concentration of humic acid (HA), anions in the environment, the reaction temperature, and pH. BPA can be totally degraded within 20 min under optimized reaction conditions. The presence of HA, Cl−, and NO3− only has a slight effect on the oxidation of BPA, whereas the presence of either H2PO4− or HCO3− can greatly inhibit the reaction. ZnCo2O4–RGO shows good cycling stability and practical application potential. A reaction mechanism of the degradation of BPA was also explored.

Electrochemical evaluation of the antioxidant capacity of natural compounds on glassy carbon electrode modified with guanine-, polythionine-, and nitrogen-doped graphene

An electrochemical sensor based on guanine-, polythionine-, and nitrogen-doped graphene modified glassy carbon electrode (G/PTH/NG/GCE) was fabricated and applied for antioxidant capacity evaluation of natural compounds and complexes in electrochemical method since natural sources of active compounds exhibited various antioxidant activities. When the antioxidants existed in the system, the generated hydroxyl radicals were scavenged and the damage to guanine immobilized on the electrode was reduced less resulting in the oxidation peak current increased in square wave voltammetry. After the modifications of polythionine- and nitrogen-doped graphene, the oxidation peak current was improved. The effects of pH, incubation time, and concentrations of guanine and Fe2+ ions on the performances of the electrode were investigated and optimized. The G/PTH/NG/GCE showed good linearity, reproducibility, and storage stability for antioxidant capacity evaluation of ascorbic acid at the optimum conditions. The antioxidant capacities of three flavonoids and three plant extracts were measured using the G/PTH/NG/GCE and DPPH methods. Myricetin showed the highest antioxidant capacity in both electrochemical and DPPH methods. The proposed G/PTH/NG/GCE exhibited easy fabrication procedure, rapid detection time, and low cost for the detection of antioxidant activity for various kinds of samples.

Activation of persulfate by stability-enhanced magnetic graphene oxide for the removal of 2,4-dichlorophenol

A stability-enhanced magnetic catalyst, composed of α-Fe₂O₃@Fe₃O₄ shell-core magnetic nanoparticles and graphene oxide (MGO), was prepared and characterized by scanning electron micrope (SEM), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), and Brunauer-Emmett-Teller (BET). Catalyst synthesis was used to efficiently activate persulfate for the removal of 2,4-dichlorophenol (2,4-DCP). A magnetic nanoparticle:GO mass ratio of 5 (MGO-5) exhibited a better catalytic efficiency and could be effectively reused four times. The influences of the pollutant, catalyst, and oxidant concentrations were investigated, and the intrinsic relationships among these factors and the degradation kinetic constant were evaluated by a fitting method. It was found that the catalytic degradation process in the MGO-5-persulfate-2,4-DCP system was most likely dominated by an interfacial catalytic reaction, with an activation energy of 13.88 kJ/mol. Radical quenching experiments and electron paramagnetic resonance (EPR) analysis indicated that both sulfate radicals (SO₄^-) and hydroxyl radicals (OH) were responsible for 2,4-DCP removal, but surface-bounded SO₄^- played a greater role. Chloride ions at a concentration of 0-60 mg/L had no effect on 2,4-DCP removal. The proposed advanced oxidation technology has potential applications for the practical removal of aqueous organic pollutants.