Adsorption of heavy metal tolerance strains to Pb2+ and Cd2+ in wastewater

Adsorptive detoxification of Cd2+ and Pb2+ from wastewater using MWCNTs functionalized with -di-(2-ethyl hexyl phosphoric acid) and bis-(2,4,4-trimethyl pentyl) phosphonic acid

Selective and rapid determination of procedure for Cd2+ and Pb2+ samples using MWCNT surfaces can be modified by loading ligands such as D2EHPA and Cyanex 272 which is described. The adsorbent was modified with D2EHPA and Cyanex 272. Effect of pH, amount of adsorbent, contact time for adsorption, and the optimum eluent for the quantitative recovery of Cd2+ and Pb2+ were investigated and the subsequent determination by FAAS. The adsorption was found to be mainly due to the chemical interactions between the metal ions and functional groups -COO- and -OH which were characterized by FT-IR. The adsorption of metal occurs at pH 4.5 with 500 mg of MWCNTs. The enrichment factor was 40 and 30. The detection limit was 0.03 and 0.05 μg L-1. The quantitative recovery of metal ion used 1 mol L-1 HNO3. The thermodynamic parameter of Langmuir and Freundlich adsorption isotherm revealed that the adsorption of free energy (ΔG) was spontaneous and the monolayer adsorption of Cd2+ and Pb2+ was mainly on the surfaces. The adsorbent performance of R2 in the range of 0.93-0.99 and also the identified adsorption efficiency of Cd2+ and Pb2+ are linear or non-linear curves respectively. The proposed method was applied to heavy metals from environmental samples.

Adsorption of Cd (II) by a novel living and non-living Cupriavidus necator GX_5: optimization, equilibrium and kinetic studies

Biosorbents have been extensively studied for heavy metal adsorption due to their advantages of low cost and high efficiency. In the study, the living and non-living biomass of Cupriavidus necator GX_5 previously isolated were evaluated for their adsorption capacity and/or removal efficiency for Cd (II) through batch experiments, SEM and FT-IR investigations. The maximum removal efficiency rates for the live and dead biomass were 60.51% and 78.53%, respectively, at an optimum pH of 6, a dosage of 1 g/L and an initial Cd (II) concentration of 5 mg/L. The pseudo-second-order kinetic model was more suitable for fitting the experimental data, indicating that the rate-limiting step might be chemisorption. The Freundlich isotherm model fit better than the Langmuir isotherm model, implying that the adsorption process of both biosorbents was heterogeneous. FT-IR observation reflected that various functional groups were involved in Cd (II) adsorption: -OH, -NH, C=O, C-O and C-C groups for the living biomass and -OH, -NH, C-H, C = O, C-N and N-H groups for the dead biomass. Our results imply that non-living biosorbents have a higher capacity and stronger strength for absorbing Cd (II) than living biomass. Therefore, we suggest that dead GX_5 is a promising adsorbent and can be used in Cd (II)-contaminated environments.

Exogenous application of low and high molecular weight organic acids differentially affected the uptake of cadmium in wheat-rice cropping system in alkaline calcareous soil

Anthropogenic cadmium (Cd) in arable soils is becoming a global concern due to its harmful effects on crop yield and quality. The current study examined the role of exogenously applied low molecular weight organic acids (LMWOAs) including oxalic acid (OxA), tartaric acid (TA) and high molecular weight organic acids (HMWOAs) like citric acid (CA) and humic acid (HA) for the bioavailability of Cd in wheat-rice cropping system. Maximum increase in root dry-weight, shoot dry-weight, and grain/paddy yields was recorded with HA for both crops. The HA significantly decreased AB-DTPA Cd in contaminated soils which remained 41% for wheat and 48% for rice compared with their respective controls. The minimum concentration of Cd in roots, shoots and grain/paddy was observed in HA treatment in both crops. The organic acids significantly increased the growth parameters, photosynthetic activity, and relative leaf moisture contents for both wheat and rice crops compared to that with the contaminated control. Application of OxA and TA increased the bioavailability of Cd in soils and plant tissues while CA and HA decreased the bioavailability of Cd in soils and plants. The highest decrease in Cd uptake, bioaccumulation, translocation factor, immobilization, translocation, harvest, and health risk indices were observed with HA while maximum increase was recorded with OxA for both wheat and rice. The results concluded that use of HMWOAs is effective in soil Cd immobilization being maximum with HA. While LMWOAs can be used for the phytoextraction of Cd in contaminated soils having maximum potential with OxA.

Comparative Study of Biochar Modified with Different Functional Groups for Efficient Removal of Pb(II) and Ni(II)

The potential application of biochar in water treatment is attracting interest due to its sustainability and low production cost. In the present study, H₃PO₄-modified porous biochar (H-PBC), ethylenediaminetetraacetic acid-modified porous biochar (E-PBC), and NaOH-modified porous biochar (O-PBC) were prepared for Ni(II) and Pb(II) adsorption in an aqueous solution. Scanning electron microscopy (SEM), X-ray diffraction analysis (XRD), Brunauer-Emmett-Teller analysis (BET), and Fourier-transform infrared (FT-IR) spectroscopy were employed to characterize the as-obtained samples, and their capacities for Ni(II) and Pb(II) adsorption were determined. SEM showed that H-PBC retained the hierarchical porous structure of pristine biochar. FT-IR showed that H-PBC possessed abundant oxygen-containing and phosphorus-containing functional groups on the surface. BET analysis demonstrated that the surface areas of H-PBC (344.17 m²/g) was higher than O-PBC (3.66 m²/g), and E-PBC (1.64 m²/g), respectively. H-PBC, E-PBC, and O-PBC all exhibited excellent performance at Ni(II) and Pb(II) adsorption with maximum adsorption capacity of 64.94 mg/g, 47.17 mg/g, and 60.24 mg/g, and 243.90 mg/g, 156.25 mg/g, and 192.31 mg/g, respectively, which were significantly higher than the adsorption capacity (19.80 mg/g and 38.31 mg/g) of porous biochar (PBC). Pseudo-second order models suggested that the adsorption process was controlled by chemical adsorption. After three regeneration cycles, the Ni(II) and Pb(II) removal efficiency with H-PBC were still 49.8% and 56.3%. The results obtained in this study suggest that H-PBC is a promising adsorbent for the removal of heavy metals from aqueous solutions.

Adsorption of Pb(II) cation from aqueous solutions by acid modified low-rank coal: An experimental study and simulation

An acid modified approach to enhance the adsorption capacity of low-rank coal (lignite) is proposed to reduce the risk of heavy metal ions within the wastewater. Adsorption kinetics, adsorption thermodynamics, adsorption coefficient and density functional theory DFT calculations were studied in this paper, respectively. The results indicate that the adsorption capacity of lignite was enlarged after HNO₃ modification, and pseudo-second order kinetics model and Langmuir isothermal adsorption model can be used to describe the adsorption process. The surface chemical properties of lignite play a dominant role rather than the specific surface area and total pore volume in the Pb(II) cation adsorption process, and it is suggested that the adsorption of Pb(II) cation by raw lignite (RL) and modified lignite (ML) is mainly completed by chemical adsorption. The Fourier transform infrared spectroscopy (FTIR) characterization showed that the surface oxygen functional groups of lignite increased after modification. The results of interaction energies between the model molecule and Pb(II) cation show that Pb(II) cation and -C-O-C are most easily combined, followed by -COOH, and -C = O is the weakest.

Template synthesis of ordered mesoporous MgO with superior adsorption for Pb(II) and Cd(II)

Ordered mesoporous MgO was synthesized via template method by using magnesium nitrate as a precursor and amphiphilic triblock copolymer Pluronic F127 as a template. The products were characterized by X-ray powder diffraction (XRD) and transmission electron microscopy (TEM), and the Brunauer-Emmett-Teller (BET) method was used to calculate the specific surface areas. The effects of aging time, relative humidity, and magnesium nitrate content on the morphology and textural properties of the products were studied. When the aging time was 36 h and the relative humidity was 40%, the ordered mesoporous MgO with uniform pore sizes (3.2 nm), high specific surface areas (517.2 m²/g), and high pore volumes (0.42 cm³/g) were obtained. Furthermore, the adsorption properties of ordered mesoporous MgO as adsorbent for removal of Pb(II) and Cd(II) ions were studied. The adsorption kinetics and isotherm data agreed well with pseudo-second-order model and Langmuir model, indicating that the adsorption of heavy metal ions on the ordered mesoporous MgO was mainly chemical and homogeneous adsorption. The maximum adsorption capacities for Pb(II) and Cd(II) ions were up to 3073.5 mg/g and 1485.1 mg/g, respectively.

Megamerger of biosorbents and catalytic technologies for the removal of heavy metals from wastewater: Preparation, final disposal, mechanism and influencing factors

Heavy metal pollution, because of its high toxicity, non-biodegradability and biological enrichment, has been identified as a global aquatic ecosystems threat in recent decades. Due to the high efficiency, low cost, satisfactory recyclability, easy storage and separation, biosorbents have exhibited a promising prospect for heavy metals treatment in aqueous phase. This article comprehensively summarized different types of biosorbents derived from available low-cost raw materials such as agricultural and forestry wastes. The raw materials obtained are treated with conventional pretreatment or novel methods, which can greatly enhance the adsorption performance of the biosorbents. The suitable immobilization methods can not only further enhance the adsorption performance of the biosorbents, but also facilitate the process of separating the biosorbents from the wastewater. In addition, once biosorbents are put into large-scale use, the final disposal problems cannot be avoided. Therefore, it is necessary to review the currently accepted final disposal methods of biosorbents. Moreover, through the analysis of the adsorption and desorption mechanisms of biosorbents, it is not only beneficial to find the better methods to improve the adsorption performance of the biosorbents, but also better to explain the influencing factors of adsorption effect for biosorbents. Especially, different from many researches focused on biosorbents, this work highlighted the combination of biosorbents with catalytic technologies, which provided new ideas for the follow-up research direction of biosorbents. Finally, the purpose of this paper is to inject new impetus into the future development of biosorbents.

Adsorption of copper ions on Magnolia officinalis residues after solid-phase fermentation with Phanerochaete chrysosporium

The disposal of residues while manufacturing Chinese medicine has always been an issue that concerns pharmaceutical factories. Phanerochaete chrysosporium was inoculated into the residues of Magnolia officinalis for solid-phase fermentation to enzymatically hydrolyze the lignin in the residues and thus to improve the efficiency of removal of the copper ions from residues for the utilization of residues from Chinese medicine. With the increase in activities of lignin-degrading enzymes, especially during the fermentation days 6 to 9, the removal rate of copper ions using M. officinalis residues increased dramatically. The rate of removal reached the maximum on the 14th day and was 3.15 times higher than the initial value. The rate of adsorption of copper ions on the fermentation-modified M. officinalis residues followed the pseudo-second-order kinetics. The adsorption isotherms were consistent with the Freundlich models. The adsorption enthalpy was positive, indicating that it was endothermic and elevation in temperature was favorable to this adsorption process. The adsorption free energy was negative, implying the spontaneity of the process. The copper ions adsorbed could be effectively recovered using 0.2 M hydrochloric acid solution. After five successive cycles of adsorption-regeneration, the fermentation-modified M. officinalis residues exhibited a stable adsorption capacity and greater reusability. The M. officinalis residues fermented with P. chrysosporium are low-cost and environmentally friendly copper ions adsorbent, and this preparation technique realizes the optimum utilization of Chinese medicine residues.

Facile synthesis of hollow mesoporous MgO spheres via spray-drying with improved adsorption capacity for Pb(II) and Cd(II)

Spherical-like MgO nanostructures have been synthesized efficiently via spray-drying combined with calcination using magnesium acetate as magnesium source. The products were characterized by means of X-ray powder diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and the specific surface areas were calculated using the Brunauer-Emmett-Teller (BET) method. The obtained spherical-like MgO nanostructures exhibit uniform pore sizes (7.7 nm) and high specific surface areas (180 m² g^-1). The adsorption kinetics and isotherm data agree well with pseudo-second-order model and Langmuir model, indicating the monolayer chemisorption of heavy metal ions. The spherical-like MgO nanostructures exhibited high adsorption performance for Pb(II) and Cd(II) ions, and the maximum adsorption capacities were up to 5214 mg g^-1 and 4187 mg g^-1, respectively. These values are much higher than those reported MgO-based adsorbents. Moreover, in less than 10 min, Pb(II) and Cd(II) ions in solution can be almost removed, which means that the spherical-like MgO possesses a high adsorption rate. XRD and FTIR analysis revealed the adsorption mechanism of Pb(II) and Cd(II) ions on MgO, which was mainly due to hydroxyl functional groups and ion exchange between Mg and heavy metal ions on the surface of MgO. These favorable performances recommend that the synthesized spherical-like MgO nanostructures would be a potential adsorbent for rapid removal of heavy metal ions from wastewater.

Characteristics and performance of Cd, Ni, and Pb bio-adsorption using Callinectes sapidus biomass: real wastewater treatment

In the current study, the bio-adsorption potential of Callinectes sapidus biomass for control of cadmium, nickel, and lead from the aqueous stream was assessed. Spectrum analysis of FTIR, AFM, EDAX, mapping, SEM, TEM, and XRF was used to study the properties of the C. sapidus biomass. The XRF analysis revealed that C. sapidus bio-adsorbent has various effective metal oxides that can be useful to adsorb pollutants. The best model to describe the equilibrium data was Freundlich isotherm. The Langmuir bio-adsorption capacity was reported at 31.44 mg g^-1, 29.23 mg g^-1, and 29.15 mg g^-1 for lead, cadmium, and nickel ions, respectively. Pseudo-first-order and pseudo-second-order kinetic models were studied to test the kinetic behavior of the process. An intra-particle diffusion model was used to determine the effective mechanisms involved in the bio-adsorption. Based on t_1/2, it can be concluded that the equilibrium speed of the bio-adsorption process is high. The thermodynamic study showed that the metal bio-adsorption process using C. sapidus biomass is exothermic and spontaneous. The field applicability of the crab bio-adsorbent for eliminating concurrently several contaminants (metal ions, antibiotics, sulfate, nitrate, and ammonium) from an actual wastewater was successfully examined.