Modified wheat straw-derived graphene for the removal of Eriochrome Black T: characterization, isotherm, and kinetic studies

Adsorption of diazinon from aqueous solution using metal organic framework and functionalized graphene: Comparison of BBD, ANN models

In the present study, metal organic frameworks (MOFs) and aminated graphitic carbonaceous structure (ACS-RGO) through chemical synthesis prepared by a simple precipitation method and used for diazinon removal. Several techniques such as XRD , FESEM and FTIR were applied for identification of MOF-5 and ACS-RGO. Also, response surface methodology (RSM) was employed in this work to look at the effectiveness of diazinon adsorption. To forecast pesticide removal, we applied artificial neural network (ANN) and Box-Behnken Design (BBD) models. For the ANN model, a sensitivity analysis was also performed. The effect of independent variables like solution pH, various concentrations of diazinon, MOFs and ACS-RGO adsorbent dose and contact time were assessed to find out the optimum conditions. Based on the model prediction, the optimal condition for adsorption ACS-RGO and MOF-5 were determined to be pH 6.6 and 6.6, adsorbent dose of 0.59 and 0.906 g/L, and mixing time of 52.15 and 36.96 min respectively. These conditions resulted in 96.69% and 80.62% diazinon removal using ACS-RGO and MOF-5, respectively. Isotherm studies proved the adsorption of ACS-RGO and MOF-5 following the Langmuir isotherm model for diazinon removal. Diazinon removal followed by the pseudo-second and Pseudo-first order kinetics model provides a better fit for analyzing the kinetic data associated with pesticide adsorption for ACS-RGO and MOF-5, respectively. Based on the obtained results, the predicted values for the efficiency of diazinon removal with the ANN and BBD were similar (R2=0.98). Therefore, two models were able to predict diazinon removal by ACS-RGO and MOF-5.

From grape bagasse to graphene-like porous carbon nanosheets for CO2 capture

Graphene-based materials have increasingly attracted attention in recent years. It is a material is recognized worldwide due to its numerous applications in several sectors. However, graphene production involves several challenges: scalability, high costs, and high-quality production. This study synthesized graphene-like porous carbon nanosheets (GPCNs) through a thermochemical process under a nitrogen atmosphere using grape bagasse as a precursor. Three temperatures (700, 800, and 900 ºC) of the pyrolysis process were studied. Chemical graphitization and activation were used to form high-specific surface area materials: FeCl3.6H2O(aq) and ZnCl2(s) in a simultaneous activation-graphitization (SAG) method. The materials obtained (GPCN700, GPCN800, and GPCN900) were compared to previously produced chars (C700, C800, and C900). A high specific surface area and total pore volume were obtained for GPCN materials, and GPCN900 presented the highest values: 1062.7 m2g-1 and 0.635 cm3 g-1, respectively. The GPCN and char materials were classified as mesoporous and applied as adsorbents for CO2(g). The GPCN800 presented the best CO2(g) adsorbent, with a CO2(g) adsorption capacity of 168.71 mg g-1.

Fabrication of nano-biocomposite for the removal of Eriochrome Black T and malachite green from aqueous solution: isotherm and kinetic studies

The increasing generation of toxic dye wastewater from various enterprises continues to be a serious public health issue and happens to be of environmental concern, posing a significant challenge to existing conventional water treatment facilities. Malachite green (MG) and Eriochrome Black T (EBT) are extremely hazardous and carcinogenic substances; hence it is crucial to remove them from water bodies. A well-known cleaner, more economical, and environmentally friendly treatment method is adsorption. The kind of adsorbent material employed determines how well the treatment procedure works. A physiologically compatible nanocomposite adsorbent (HAP@CT@MNP) was fabricated from laboratory synthesized hydroxyapatite (HAP) and magnetite (MNP) for its application in the wastewater remediation process. The ability of the fabricated nanocomposite to remove the harmful dyes EBT and MG from a simulated wastewater was evaluated. The impact of operational parameters including pH, adsorbate concentration, adsorbent dose, contact time, and temperature was examined to gauge the maximum adsorption capacity of the developed nanocomposite. The optimum pH for the eradication of EBT and MG were found to be 3 and 7.4, respectively. The maximum capacity evaluated was 222 mg/g and 500 mg/g at room temperature and at contact time of 50 and 40 min respectively. The binding of either EBT or MG followed the monolayer Langmuir model and kinetic studies revealed the suitability of pseudo-second-order model. Studies using spectroscopy and isotherm modeling showed that the main mechanism controlling the adsorption of EBT and MG onto HAP@CT@MNP is physisorption. The efficacy of the adsorbent to be reused with 8% loss in its efficiency reveals the economic viability of HAP@CT@MNP. The current work showed that a biocompatible nanocomposite could be successfully fabricated and used as an enhanced adsorbent for the quick and effective removal of the toxic dyes EBT and MG from wastewater.

Recent advances in biopolymer-based advanced oxidation processes for dye removal applications: A review

Over the past few years, synthetic dye-contaminated wastewater has attracted considerable global attention due to the low biodegradability and the ability of organic dyes to persist and remain toxic, causing numerous health and environmental concerns. As a result of the recalcitrant nature of those complex organic dyes, the remediation of wastewater using conventional wastewater treatment techniques is becoming increasingly challenging. In recent years, advanced oxidation processes (AOPs) have emerged as a potential alternative to treat organic dyestuffs discharged from industries. The most widely employed AOPs include photocatalysis, ozonation, Fenton oxidation, electrochemical oxidation, catalytic heterogeneous oxidation, and ultrasound irradiation. These processes involve the generation of highly reactive radicals to oxidize organic dyes into innocuous minerals. However, many conventional AOPs suffer from several setbacks, including the high cost, high consumption of reagents and substrates, self-agglomeration of catalysts, limited reusability, and the requirement of light, ultrasound, or electricity. Therefore, there has been significant interest in improving the performance of conventional AOPs using biopolymers and heterogeneous catalysts such as metal oxide nanoparticles (MONPs). Biopolymers have been widely considered in developing green, sustainable, eco-friendly, and low-cost AOP-based dye removal technologies. They inherit intriguing properties like biodegradability, renewability, nontoxicity, relative abundance, and sorption. In addition, the immobilization of catalysts on biopolymer supports has been proven to possess excellent catalytic activity and turnover numbers. The current review provides comprehensive coverage of different AOPs and how efficiently biopolymers, including cellulose, chitin, chitosan, alginate, gelatin, guar gum, keratin, silk fibroin, zein, albumin, lignin, and starch, have been integrated with heterogeneous AOPs in dye removal applications. This review also discusses the general degradation mechanisms of AOPs, applications of biopolymers in AOPs and the roles of biopolymers in AOPs-based dye removal processes. Furthermore, key challenges and future perspectives of biopolymer-based AOPs have also been highlighted.

Engineered biochar supported layered double hydroxide-cellulose nanocrystals composite-: Synthesis, characterization and azo dye removal performance

In this work, engineered biochar decorated layered double hydroxides and cellulose nanocrystals (B-CuFe-CNC) biocomposites were synthesized by the facile ultrasonicated-co-precipitation technique. The biocomposite was investigated for purification of Eriochrome Black T (EBT) dye from water. The characterization results showed that the presence of CNC in biochar-layered double hydroxides resulted in a two-dimensional rod-like structure with excellent crystallinity, improved surface functionalities, and provides an attractive platform for the enhanced adsorption of azo anionic dye molecules. The adsorption system was appropriately demonstrated by the BBD-RSM (R² > 0.994). The biocomposite exhibited higher EBT adsorption in the acidic pH range (2-5) due to strong electrostatic and chemical interactions. The kinetic and isotherm results were well demonstrated by pseudo-second order, Freundlich, and Redlich Peterson models. The maximum adsorption capacity of biocomposite was 876.2 mg/g achieved within 45 min. The spectroscopic analyses imply that the high removal of EBT by biocomposite is mainly governed by electrostatic attraction, hydrogen bonding, and chemical/metal complexation mechanisms. The biocomposite maintained high EBT removal after six successive adsorption cycles and excellent dye adsorption in the different water matrices. The results suggest that tailoring biochar properties with layered double hydroxide and CNC is a promising way for the enhanced removal of dye contaminants from wastewater.

Comparative removal of hazardous cationic dyes by MOF-5 and modified graphene oxide

Among cationic dyes, malachite green (MG) is commonly used for dying purposes and also as an inhibitor in aquaculture, food, health, and chemical industries due to its cytotoxic effects. Therefore, MG removal is essential to keep the ecosystem and human health safety. Adsorption is a viable and versatile option and exploring efficient adsorbents have high priority. Herein, MOF-5 and aminated corn Stover reduced graphene oxide (ACS-RGO) of typical adsorbents of metal-organic-frameworks (MOFs) and carbon-based classes were studied for MG removal. MOF-5 and ACS-RGO had a specific surface area and total pore volume of 507.4 and 389.0 m2/g, and 0.271 cm3/g and 0.273 cm3/g, respectively. ACS-RGO was superior for MG adsorption and the kinetic rate coefficient for ACS-RGO was ~ 7.2 times compared to MOF-5. For ACS-RGO, MG removal remained high (> 94%) in a wide range of pH. However, dye removal was pH-dependent for MOF-5 and increased from ~ 32% to ~ 67% by increasing pH from 4 to 12. Increasing dye concentration from 25 mg/L to 100 mg/L decreased adsorption by MOF-5 and ACS-RGO for ~ 30% and 7%, respectively. Dye removal was evident in a few tens of seconds after adding ACS-RGO at doses above 0.5 g/L. A significant loss of 46% in adsorption was observed by decreasing MOF-5 mass from 1 to 0.1 g/L. ACS-RGO removed MG in multilayer with an exceptional adsorption capacity of 1088.27 mg/g. In conclusion, ACS-RGO, and MOF-5 showed promising kinetic rates and adsorption capacities toward MG.

The boosted activity of AgI/BiOI nanocatalyst: a RSM study towards Eriochrome Black T photodegradation

Nowadays, critical environmental pollution needs some novel, simple, effective, and cost-effective catalysts with high efficiency in the visible region of the light. Thus, the AgI/BiOI coupled nanocatalyst sample (CS) was prepared and briefly characterized. The pH_pzc values of 6.2, 5.4, and 4.5 were estimated for AgI, BiOI, and AgI/BiOI samples. Based on the PXRD results, average crystallite sizes of 35.2, 34.7, and 34.1 nm were obtained for AgI, BiOI, and AgI/BiOI samples from the Scherrer formula and 38.3, 25.6, and 25.6 nm by the Williamson-Hall formula. SEM image confirmed a sheet-like BiOI morphology covered by AgI nanoparticles. The simultaneous interactions of the influencing variables on the boosted photocatalytic activity of CS sample towards Eriochrome Black T (EBT) were evaluated by response surface methodology (RSM) (under 100-W tungsten lamp irradiation with 230 mW/m².nm irradiance). The goodness of the model was confirmed by the significance of the model (F value of 65.68 > F_{0.05, 14, 13} = 2.55) and a non-significant LOF (F value of 0.97 < F_{0.05, 10, 3} = 8.79) at a 95% confidence interval obtained in ANOVA analysis of the results. The center point runs have the following conditions: catalyst dose: 0.68 g/L; pH: 7.5; C_EBT: 7.25 mg/L; and irradiation time: 53.5 min, while the optimal run included the following conditions: catalyst dose: 1.0 g/L; pH: 4; C_EBT: 10 mg/L; and irradiation time: 80 min. About 95% of EBT molecules were degraded in the optimal conditions.

Preparation and application of polyethyleneimine-modified corncob magnetic gel for removal of Pb(ii) and Cu(ii) ions from aqueous solution

As a biomass resource, corncob is a kind of agricultural by-product with wide sources and low cost. Because its composition contains a large number of functional polymers such as cellulose, chitosan, and semi chitosan, corncob can be chemically modified to prepare a variety of adsorption materials. In this study, a magnetic gel material (PEI-CC@Fe3O4) consisting of corncob modified by glutaraldehyde-crosslinked polyethyleneimine (PEI) was successfully prepared and applied to the adsorption of heavy metal ions in aqueous solutions. The structure, thermal stability, and adsorption of heavy metal ions of the magnetic gel material (PEI-CC@Fe3O4) were characterized by Fourier-transform infrared spectroscopy (FT-IR), X-ray diffraction phase analysis (XRD), scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and X-ray photoelectron spectroscopy (XPS). The results showed that PEI was crosslinked to the corncob through Aldol reaction and Schiff-base reaction. The heavy metal ion adsorption experiment showed that the PEI-CC@Fe3O4 had better adsorption toward divalent copper ions and divalent lead ions at 303 K, and the maximum adsorption capacities reached 459.4 mg g-1 and 290.8 mg g-1, respectively. Moreover, the study of isothermal adsorption and adsorption kinetics shows that the adsorption process is pseudo-second-order kinetics model adsorption, which belongs to Langmuir isothermal adsorption. Such excellent adsorption performance will contribute to the application of corncob biomass materials in industrial polluted wastewater.

Effective Cd2+ removal from water using novel micro-mesoporous activated carbons obtained from tobacco: CCD approach, optimization, kinetic, and isotherm studies

PURPOSE

This research aimed to develop activated carbons from tobacco by double (thermal-physical) and triple activations (thermal-chemical-physical) for high-efficiency removal of Cd²⁺.

METHODS

The adsorbents were characterized by their chemical composition, point of zero charge (pH_PZC), SEM, FT-IR, BET, and BJH. The subsequent adsorption studies were conducted: optimal conditions (CCD on adsorbent dose versus pH of Cd²⁺ solution), kinetics, equilibrium, thermodynamics, and desorption studies.

RESULTS

The activated carbons have irregular and heterogeneous morphology, surface functional groups COO-, C-O, C-O-C, C=O and O-H, pH_PZC of 11.11 and 10.86, and enhanced SSA (especially for CT NaOH + CO₂ = 103.40 g m^-2). The optimal conditions for Cd²⁺ adsorption occur using 4.0 g L^-1, pH from 3.0 to 7.0, with most of the Cd²⁺ adsorbed in the first 10-20 min. The goodness of the fit found for pseudo-first order, pseudo-second order, intraparticle diffusion, Langmuir, Freundlich, Dubinin-Radushkevich, Sips, and Temkin suggest the occurrence of Cd²⁺ chemisorption and physisorption in mono and multilayers. The values of ∆G° < 0 kJ mol^-1 indicate that the observed phenomena are energetically favorable and spontaneous; the values of ∆H° < 0 and the effective desorption rates (58.52% and 44.64%) suggest that the adsorption of Cd²⁺ is ruled mainly (but not only) by physical interactions.

CONCLUSION

Our excellent results on Cd²⁺ removal allow us to state that tobacco use as a raw material for adsorbent development is a renewable and eco-friendly technique, allowing the production of highly effective activated carbons and providing an adequate destination for this waste.

SUPPLEMENTARY INFORMATION

The online version contains supplementary material available at 10.1007/s40201-021-00740-8.

Defluoridationof drinking water by metal impregnated multi-layer green graphene fabricated from trees pruning waste

A novel adsorbent with excellent adsorptive properties for fluoride was prepared through a green and cheap synthesis route. Populus caspica pruning wastes, a cheap agri-waste material, were reduced to multi-layer green graphene (MLG) and then post-modified to aluminum/iron modified multi-layer green graphene (AMLG and IMLG). Batch experiments revealed the effect of pH (3-11), contact time (0.5-12 h), and initial fluoride concentration (5-40 mg/L). The conversion of raw material to MLG increased the specific surface area about 120 times (from 4 to 475 m²/g). Furthermore, a significant improvement in zero points of charge (pHzpc) was attained for IMLG (7.1) and AMLG (8) compared with pristine MLG (4.3). Fluoride showed superior affinity to AMLG and IMLG compared with MLG. Fluoride removal increased gradually by pH from 3 to 8 and then decreased sharply up to pH 11. The study of process dynamics demonstrated the monolayer fluoride adsorption onto AMLG and IMLG controlled by the chemisorptions. The highest predicted adsorption capacities based on the Langmuir model were 31.52, 47.01, and 53.76 mg/g for MLG, IMLG, and AMLG, respectively. Considering economic and technical feasibility presents AMLG and IMLG as a promising candidate against water contamination by elevated fluoride. Graphical abstract.

Novel Fe3O4-poly(methacryloxyethyltrimethyl ammonium chloride) adsorbent for the ultrafast and efficient removal of anionic dyes

The removal of anionic dyes from wastewater has attracted global concern. In this work, a novel Fe3O4-poly(methacryloxyethyltrimethyl ammonium chloride) (Fe3O4-pDMC) adsorbent for the efficient removal of anionic dyes from wastewater was successfully synthesized by grafting methacryloxyethyltrimethyl ammonium chloride (DMC) on the surfaces of Fe3O4. Various characterization analyses confirmed that the obtained Fe3O4-pDMC possessed numerous functional groups on its surfaces and retained good magnetic separation properties. Fe3O4-pDMC showed ultrafast removal for acid orange 7 (AO7, 58.6%, 1 min) and direct blue 15 (DB15, 98.1%, 1 min), and the maximum adsorption capacity was high (266.8 and 336.5 mg g-1 for AO7 and DB15, respectively). In addition, the adsorption process was in accordance with pseudo-second-order kinetics and the Langmuir isotherm. The mechanism underlying the adsorption of Fe3O4-pDMC on anionic dyes was mainly dependent on electrostatic interaction. This study illustrated that Fe3O4-pDMC has great potential applications as an environmentally friendly, desirable adsorbent for the efficient removal of anionic dyes from wastewater.