The potential use of ultrasound-assisted bleaching in removing heavy metals and pigments from soybean oil using kinetic, thermodynamic and equilibrium modeling

The ultramicropore biochar derived from waste distiller's grains for wet-process phosphoric acid purification: Removal performance and mechanisms of Cr(VI)

Solid waste and heavy metal pollution are long-term and challenging subjects in the field of environmental engineering. In this study, we propose a sustainable approach to "treating waste with waste" by utilizing the ultramicropore biochar derived from solid waste distiller's grains as a means to remove Cr(VI) from simulated wastewater and wet phosphoric acid. The biochar prepared in this research exhibit extremely high specific surface areas (up to 2973 m2/g) and a well-developed pore structure, resulting in a maximum Cr(VI) adsorption capacity of 426.0 mg/g and over 99% removal efficiency of Cr(VI). Furthermore, the adsorbent can be reused for up to eight cycles without significant reduction in its Cr(VI) adsorption performance. Mechanistic investigations suggest that the exceptional Cr(VI) adsorption capacity can be attributed to the synergistic effect of electrostatic interaction and reduction adsorption. This study offers an alternative approach for the resource utilization of solid waste distiller's grains, and the prepared biochar holds promise for the removal of Cr(VI) from wastewater and wet-process phosphoric acid.

High-power ultrasound bleaching technique for canola oil (Brassica napus L.): Pigments removal and quality parameters

Canola seeds (Brassica napus L.) are among the most commonly used seeds in Mexico for vegetable oil production. This is based on the high yield and content of polyunsaturated and monounsaturated fatty acids. During oil bleaching, it is important to maintain fatty acids in their cis configuration because of the health concerns associated with trans-fatty acid consumption. In this sense, the industrial processing parameters employed for this purpose present some limitations, such as high temperatures and long times, which may change the cis configuration to trans. In addition, the amount of bleaching clay employed for this process could be a source of contamination because it is disposed of after treatment. Therefore, the aim of this study was to develop a bleaching process for canola oil using high-power ultrasound (US). US processing was applied to nine treatments with different processing times (60, 75, and 90 min), clay percentages (1, 2, and 3%), and temperatures (60 and 80 °C) to determine the concentrations of chlorophyll a and b (µg chlo/100 g oil), carotenes (µg β-carotene/100 g oil), color (L*, a*, b*, C*, and h°), iodine value (g I2/100 g oil), and finally carrying out a spectroscopic analysis (ATR-FTIR and Raman). A conventional bleaching treatment (100 °C for 180 min, 3% bleaching clay) was used as a control. The results revealed that US treatments with 2% clay at 60 °C for 60 and 90 min eliminated most of the chlorophyll compounds (98%). However, in terms of carotenes reduction, these identical treatments exhibited a similar tendency to that of the control (approximately 30% decrease). These findings also affected the sample color, in which US treatments revealed chromatic coordinates that indicated yellow tones with chroma values that were more intense than those in the control samples. In terms of the iodine value, such treatments fulfilled the international standards for vegetable oils (90-100 g I2/100 g oil). Finally, the spectroscopic study revealed no trans configurations or the presence of different chemical compounds after US treatment, because neither of them presented typical peaks for those molecular configurations. In this regard, US can be a useful methodology for bleaching vegetable oils, helping to reduce time, and bleaching clay with similar pigment reduction results.

Preparation and characterization of biopolymer-based adsorbents and their application for methylene blue removal from wastewater

In the present study, four biopolymer-based materials consisting of native corn starch (CS), phosphate corn starch (PS), starch nanocrystals (SNCs), and phosphate corn starch nanocrystals (PSNCs) were synthesized and used for methylene blue (MB) removal as a function of various parameters, including initial MB concentration (C0, 10-500 mg L-1), adsorbent dosage (Cs, 0.02-0.15 g), contact time (t, 5-15 min), solution pH (2-11), and temperature (25-45 °C). The removal percentage of MB increased dramatically upon increasing the biopolymer dosage, temperature, and pH; while it decreased upon increasing the initial MB concentration. The adsorption behavior of biopolymer-based materials towards MB was found to be accurately described by the pseudo-second-order kinetic and Langmuir isotherm models. According to the Langmuir model, the maximum adsorption capacities of the adsorbents were ordered as follows: PSNCs (88.53 mg g-1) > SNCs (79.55 mg g-1) > PS (73.17 mg g-1) > CS (63.02 mg g-1). PSNCs was able to remove 96.8% and 76.5% of 20 mg L-1 MB in greywater and petrochemical wastewater, respectively, at an optimum pH of 9 and retained 86.42% of its usability even after five adsorption-desorption cycles. The analysis of the surface charge of the adsorbents before and after MB adsorption, combined with the FTIR spectrum of MB-saturated biopolymer-based materials, provided evidence that electrostatic interactions was the primary mechanism involved in the adsorption of MB. Meanwhile, hydrogen bonding and π-π interactions were found to have a minor contribution to the adsorption process. Based on the results, it can be inferred that PSNCs has promising potential as an adsorbent for the treatment of MB-containing wastewater, owing to its exceptional properties, which include high adsorption capacity, low cost, and applicability for multiple reuses.