Strategic combination of metal-organic frameworks and C3N4 for expeditious photocatalytic degradation of dye pollutants

Nylon fiber waste as a prominent adsorbent for Congo red dye removal

In this research nylon fibers wastes (NF) were fabricated into porous sheet using a phase inversion technique to be utilized as an adsorbent materials for Congo red dye (CR). The fabricated sheet denoted as NS was characterized using FTIR and XRD. The surface studies of the adsorbent materials using SEM and BET analysis reveals a highly pores structure with an average pore volume 0.61 cc/g and BET surface area of 767 m2/g. The adsorption studies of fabricated NS were employed into CR at different parameters as pH, effect of time and dye concentration. The adsorption isotherm and kinetic studies were more fit to Langmuir and pseudo second order models. The maximum adsorption capacity qmax reached 188 mg/g with removal percentage of 95 for CR concentration of 400 mg/L at pH 6 and 0.025 g NS dose for 10 ml CR solution. The regeneration study reveals a prominent adsorption behavior of NS with removal % of 88.6 for CR (300 mg/L) after four adsorption desorption cycles. Effect of incorporation of NaonFil Clay to NS was studied using Response Surface Methodology (RSM) modeling and reveals that 98.4% removal of CR could be achieved by using 19.35% wt. of fiber with 8.2 g/L dose and zero clay, thus at a predetermined parameters studies of NanoFil clay embedded into NS, there are no significant effect for %R for CR.

Metal-organic frameworks for wastewater treatment: Recent developments, challenges, and future prospects

Wastewater treatment is critically important for the existence of life on earth; however, this approach involves the removal of toxic metal contaminants and organic pollutants, requiring efficient adsorbent materials. Within this agenda, metal-organic frameworks (MOFs) appear to be potential materials due to their unique properties as efficient adsorbents, effective photocatalysts, and reliable semi-permeable membranes. Therefore, MOFs have undergone various modifications over the years without desirable success to improve adsorption capacity, hydro-stability, reaction kinetics, and reusability. Therefore, scientists around the world got engaged in MOF research for novel modifications, including defect engineering, carbonization, and membrane fabrication, at the laboratory scale. This review focuses on developing MOF-based adsorbents, photocatalysts, and semi-permeable membranes for wastewater treatment since 2015, emphasizing their structural-functional relationships. Finally, the challenges and opportunities with MOFs in wastewater treatment are also underlined for future efforts.

Double-Shelled Porous g-C3 N4 Nanotubes Modified with Amorphous Cu-Doped FeOOH Nanoclusters as 0D/3D Non-Homogeneous Photo-Fenton Catalysts for Effective Removal of Organic Dyes

Graphite phased carbon nitride (g-C₃ N₄ ) has attracted extensive attention attributed to its non-toxic nature, remarkable physical-chemical stability, and visible light response properties. Nevertheless, the pristine g-C₃ N₄ suffers from the rapid photogenerated carrier recombination and unfavorable specific surface area, which greatly limit its catalytic performance. Herein, 0D/3D Cu-FeOOH/TCN composites are constructed as photo-Fenton catalysts by assembling amorphous Cu-FeOOH clusters on 3D double-shelled porous tubular g-C₃ N₄ (TCN) fabricated through one-step calcination. Combined density functional theory (DFT) calculations, the synergistic effect between Cu and Fe species could facilitate the adsorption and activation of H₂ O₂ , and the separation and transfer of photogenerated charges effectively. Thus, Cu-FeOOH/TCN composites acquire a high removal efficiency of 97.8%, the mineralization rate of 85.5% and a first-order rate constant k = 0.0507 min^-1 for methyl orange (MO) (40 mg L^-1 ) in photo-Fenton reaction system, which is nearly 10 times and 21 times higher than those of FeOOH/TCN (k = 0.0047 min^-1 ) and TCN (k = 0.0024 min^-1 ), respectively, indicating its universal applicability and desirable cyclic stability. Overall, this work furnishes a novel strategy for developing heterogeneous photo-Fenton catalysts based on g-C₃ N₄ nanotubes for practical wastewater treatment.

Direct Z-Scheme CoFe2O4-Loaded g-C3N4 Photocatalyst with High Degradation Efficiency of Methylene Blue under Visible-Light Irradiation

Magnetically recyclable direct Z-scheme CoFe2O4-loaded g-C3N4 photocatalyst material was fabricated using a facile hydrothermal technique and subsequently characterized by XRD, VSM, PL, FT-IR, EDX, DRS, SEM, and BET techniques. The characterization results confirmed that nanoparticles of CoFe2O4 are loaded on the surface of g-C3N4 sheets. The optical band gap of g-C3N4 has been decreased from 2.65 eV to 1.30 eV by means of the loading of CoFe2O4 nanoparticles onto the nanosheets of g-C3N4. This has enhanced the separation process of electron-hole. Under visible light irradiation, the photocatalytic activity of the developed direct Z-scheme CoFe2O4-loaded g-C3N4 photocatalyst was evaluated for the photodegradation of methylene blue (MB); during this process the MB decomposed by up to 98.86% in 140 min. Meanwhile, under the same irradiation and time conditions, the g-C3N4 and CoFe2O4 themselves degraded MB up to 74.92% and 51.53%, respectively. The direct Z-scheme CoFe2O4-loaded g-C3N4 material was recovered from the solution after the photocatalytic activity using an external magnet and studied to determine its stability. It was shown that the photoactivity did not change significantly after five consecutive cycles.

Facile synthesis and comparative study of the enhanced photocatalytic degradation of two selected dyes by TiO2-g-C3N4 composite

Photocatalysis is considered a useful technique employed for the dye degradation through solar light, visible or UV light irradiation. In this study, TiO₂, g-C₃N₄, and TiO₂-g-C₃N₄ nanocomposites were successfully synthesized and studied for their ability to degrade Rhodamine B (RhB) and Reactive Orange 16 (RO-16), when exposed to visible light. The analytical techniques including XRD, TEM, SEM, DRS, BET, XPS, and fluorescence spectroscopy were used to explore the characteristics of all the prepared semiconductors. The photocatalytic performance of synthesized materials has been tested against both the selected dyes, and various experimental parameters were studied. The experimental results demonstrate that, in comparison to other fabricated composites, the TiO₂-g-C₃N₄ composite with the optimal weight ratio of g-C₃N₄ (15 wt%) to TiO₂ has shown outstanding degrading efficiency against RhB (89.62%) and RO-16 (97.20%). The degradation experiments were carried out at optimal conditions such as a catalyst load of 0.07 g, a dye concentration of 50 ppm, and a temperature of 50 ℃ at neutral pH in 90 min. In comparison to pure TiO₂ and g-C₃N₄, the TiO₂-g-C₃N₄, a semiconductor, has shown higher degradation efficiency due to its large surface area and decreased electron-hole recombination. The scavenger study gave an idea about the primary active species (^-OH radicals), responsible for dye degradation. The reusability of TiO₂-g-C₃N₄ was also examined in order to assess the composite sustainability.

Recent Advances in g-C3N4-Based Materials and Their Application in Energy and Environmental Sustainability

Graphitic carbon nitride (g-C₃N₄), with facile synthesis, unique structure, high stability, and low cost, has been the hotspot in the field of photocatalysis. However, the photocatalytic performance of g-C₃N₄ is still unsatisfactory due to insufficient capture of visible light, low surface area, poor electronic conductivity, and fast recombination of photogenerated electron-hole pairs. Thus, different modification strategies have been developed to improve its performance. In this review, the properties and preparation methods of g-C₃N₄ are systematically introduced, and various modification approaches, including morphology control, elemental doping, heterojunction construction, and modification with nanomaterials, are discussed. Moreover, photocatalytic applications in energy and environmental sustainability are summarized, such as hydrogen generation, CO₂ reduction, and degradation of contaminants in recent years. Finally, concluding remarks and perspectives on the challenges, and suggestions for exploiting g-C₃N₄-based photocatalysts are presented. This review will deepen the understanding of the state of the art of g-C₃N₄, including the fabrication, modification, and application in energy and environmental sustainability.

Heterostructured ZnCdS@ZIF-67 as a Photocatalyst for Fluorescent Dye Degradation and Selectively Nonenzymatic Sensing of Dopamine

Dopamine (DA) plays the role of the transmitter of information in the brain. Neurological diseases and depression are in close relationship with DA release. In this study, we developed a co-catalyst Zn_0.2Cd_0.8S@zeolitic imidazolate framework-67 (Zn_0.2Cd_0.8S@ZIF-67) to improve the photocatalyst efficacy of Rhodamine B (RhB) and electrochemical sensing of DA. Results show that Zn_0.2Cd_0.8S@ZIF-67 exhibits optimal photocatalytic activity with the addition of 80 mg ZIF-67. The degradation percentage of RhB by Zn_0.2Cd_0.8S@ZIF-67 reached 98.40% when the co-catalyst was 50 mg. Radical trapping experiments show that ·O₂^- played a significant role in the photocatalytic degradation of RhB. The catalytic mechanism of the Zn_0.2Cd_0.8S@ZIF-67 was found as a Z-type photocatalysis. Finally, a DA biosensor was constructed and displayed a high response and selectivity to DA. This can be attributed to the heterojunction between Zn_0.2Cd_0.8S and ZIF-67, which can significantly enhance the separation of e^-/h⁺ and improve charge transfer. These findings will play a positive role in the in-situ monitoring of neurological diseases and depression.

Rational synthesis and characterization of highly water stable MOF@GO composite for efficient removal of mercury (Hg2+) from water

The present study is aimed at adsorptive removal of Mercury (Hg²⁺) using highly functionalized nanomaterials based on Graphene Oxide Zeolitic Imidazolate Framework composite (ZIF-67@GO). Solvothermal methodology was used to synthesize ZIF-67@GO composite. Synthesized compounds were confirmed by FTIR, SEM, PXRD and EDX analysis. The as-prepared ZIF-67@GO was tested as efficient adsorbent for effective removal of Mercury (Hg²⁺) from aquatic environment. The atomic adsorption spectrophotometer was used to monitor the process of adsorption of Hg⁺² on ZIF-67@GO. From the adsorption data, the maximum removal efficiency achieved was 91.1% using 10 mg amount of composite for 50 mL using 20 ppm Mercury (Hg²⁺) solution. Different parameters like pH, contact time, concentration, adsorption kinetics and isotherm were also examined to explore adsorption process. Adsorption data fitted well for Freundlich Model having R² value of 0.9925 than Langmuir Isotherm with R² value of 0.9238. Kinetics were rapid and excellently described via 2nd order model with R² = 0.99946 than 1st order model with R² value of 0.8836. Freundlich and pseudo 2nd order models validated that multilayer chemisorption occurs during adsorption process due to the presence of highly functionalized sites on ZIF-67@GO composite. The synthesized composite material has shown excellent reusability. Thus, water stable ZIF-67@GO composites can efficiently be used for Mercury (Hg²⁺) confiscation from water.

Kinetic Study of the Removal of Methyl Orange Dye by Coupling WO3/H2O2

In the present work, the heterogeneous Fenton-like process was employed to investigate the kinetic models of the degradation of methyl orange (MO) using tungsten oxide/hydrogen peroxide couple. Tungsten oxide particles were successfully synthesized by reflux without surfactant and characterized by using XRD, SEM, TEM, and FT-IR techniques. The influence of parameters such as temperature and concentration of MO was studied and pseudo first-order and second-order models were applied. WO3/H2O2 showed high efficiency in the removal of methyl orange and attained more than 92.8% in 180 min. The first-order kinetic model was described by the removal process with the correlation coefficient of R2 = 0.99.