Quick and hassle-free smartphone's RGB-based color to photocatalytic degradation rate assessment of malachite green dye in water by fluorescent Zr-N-S co-doped carbon dots

Based on mutated aptamer-smartphone colorimetric detection of metronidazole in milk

Excessive residue of metronidazole (MNZ) in food is harmful to the human body. There is an urgent demand to develop a portable tool for MNZ detection on-site. In this study, fifteen aptamers were prepared through targeted base mutation. Apt1-3 with the highest enrichment was chosen for further study. Its affinity was characterized by molecular docking simulation, AuNPs colorimetric assay, graphene oxide (GO) fluorescence assay, and exonuclease assay. Kd was determined by GO fluorescence assay (Kd: 92.60 ± 25.59 nM). Its specificity was also characterized by an exonuclease assay. A novel aptasensor was constructed by using the newly identified aptamer combined with the smartphone dark box. The principle of color change is caused by the aggregation state of AuNPs. Smartphones act as reading instruments. The detection can be completed in just a few seconds without the aid of instruments, achieving a detection limit of 0.15 nmol/mL and a range of 6.7-44.4 nmol/mL (R 2 = 0.9810). Therefore, the constructed smartphone colorimetric sensor based on mutant aptamers has important applications in food detection.

Circular economical approach of extracting nanocarbons from waste pea peel for sensing of p-nitrophenol and its conversion into paracetamol

An important paradigm shift towards the circular economy is to prioritize waste prevention, reuse, recycling, and recovery before disposal is necessary. In this context, a sustainable protocol of converting waste pea peel (wPP) into low-cost carbon nanomaterials for sensing and conversion of p-nitrophenol (p-NP) into value-added paracetamol is being reported. Two fractions of the carbonaceous nanomaterials were obtained after the hydrothermal treatment (HT) of wPP, firstly an aqueous portion containing water-soluble carbon dots (wPP-CDs) and a solid residue, which was converted into carbonized biochar (wPP-BC). Blue-colored fluorescent wPP-CDs displayed excitation-dependent and pH-independent properties with a quantum yield (QY) of 8.82 %, which were exploited for the fluorescence sensing of p-NP with 4.20 μM limit of detection. Pyrolyzed biochar acting as an efficient catalyst effectively reduces p-NP to p-aminophenol (p-AP) in just 16 min with a 0.237 min-1 rate of conversion. Furthermore, the produced p-AP was converted into paracetamol, an analgesic and antipyretic drug, to achieve zero waste theory. Thus, this study provides the execution of sustainable approaches based on the integral valorization of biowaste that can be further recycled and reused, offering an effective way to attain a profitable circular economy.

Batch Experimental Studies and Statistical Modeling for the Effective Removal of Tetracycline from Wastewater Using Bimetallic Zn-Cu-Metal-Organic Framework@Hydrogel Composite Beads

Antimicrobial resistance (AMR) is on an upsurge as more and more broad-spectrum antibiotics are being used haphazardly, resulting in imbalances in the ecosystem and disrupting common/systematic clinical protocols. To combat this issue, metal-organic framework embedded zinc-copper-benzenedicarboxylate@calcium alginate composite beads (Zn-Cu-BDC@CA CBs) were synthesized and utilized for the adsorption of tetracycline (TC) from water. The surface morphology, presence of functional groups, surface area, and thermal stability of Zn-Cu-BDC@CA CBs were evaluated by field emission scanning electron microscopy (FESEM), Fourier transform infrared spectroscopy (FTIR), Brunauer-Emmett-Teller (BET), and thermal gravimetric analysis (TGA), respectively. Batch adsorption experiments were also carried out to optimize the adsorption performance of Zn-Cu-BDC@CA CBs for TC by adjusting the key parameters, including pH of the solution, contact time, adsorbent dosage, temperature, and initial concentration of TC. From the RSM model, 96.8% removal of TC takes place under the optimum conditions (pH = 7.3, mass = 17.2 mg, concentration = 21.3 ppm, time = 3.4 h, and temperature = 31.8 °C), which aligns closely with the experimental batch study, where the addition of 20 mg of adsorbent to a 20 mL TC solution (20 mg/L) at a pH of 7 and a temperature of 27 °C yielded an impressive TC removal efficiency of 96.55% within 180 min. Zn-Cu-BDC@CA CBs possess homogeneous adsorption surfaces, and TC is adsorbed via monolayer chemisorption, according to the results derived from the Langmuir isotherm model and pseudo-second-order kinetic model. The thermodynamic analysis indicated that the adsorption process is both endothermic and spontaneous. In their entirety, the synthesized Zn-Cu-BDC@CA CBs exhibit certain operational advantages, such as simple separation, satisfactory adsorption performance, and decent recyclability, indicating their viability for industrial application of elimination of TC residues from aquatic environments.

Biogenic synthesis of highly fluorescent carbon dots using Azadirachta indica leaves: An eco-friendly approach with enhanced photocatalytic degradation efficiency towards Malachite green

A simpler and efficient method has been developed for the green synthesis of highly fluorescent carbon dots (CDs) from Azadirachta Indica leaves. The surface morphology of developed CDs has shown the existence of spherical particles in the size range of 3-8 nm with superior biocompatibility and high quantum yield value i.e. 42.3%. The particles exhibited a highly fluorescent and crystalline nature along with a bandgap value of 4.02 eV. The prepared CDs served as a factorial design for the sensing and degradation of Malachite green among other dyes. The main perspective of the current finding is that the designed catalyst exhibits excellent sensing results towards Malachite green with a limit of detection i.e. 0.144 μM in the concentration range of 0-50 μM. Moreover, the UV triggered results of photocatalysis illustrated a good dye removal efficacy by developed CDs with an average of 90.73, 98.25, 52 and 6.13% degradation in Methylene blue (MB), Malachite green (MG), Rhodamine 6G (Rh 6G) and Methyl orange (MO) upon 70 min of irradiation with mercury lamp. Additionally, the proton NMR, FTIR and FESEM results of the recycled samples also confirm the complete degradation of MG dye with the application of N-CDs.

Waste to value transformation: Converting Carica papaya seeds into green fluorescent carbon dots for simultaneous selective detection and degradation of tetracycline hydrochloride in water

Rampant use of antibiotics has resulted in their seepage into groundwater and ultimately ending up in the food chain, causing antimicrobial resistance. To address this issue, it is imperative to not only quantitatively detect but eliminate them from water. An eco-friendly, one-step microwave-induced pyrolysis of waste papaya seeds (PS) with ethylenediamine (EDA) for just 5min gave green fluorescent nitrogen-doped carbon dots (PS-CDs), which are capable of detecting and photocatalytically degrading TC. The fluorescence properties of PS-CDs displayed that it has high sensitivity and selectivity towards sensing of TC with a detection limit as low as 120 nM. Also, the method gave satisfactory recovery results when extrapolated to determine TC in spiked milk, orange juice, tap water, and honey samples. On the other hand, PS-CDs alone potentially function as an efficient photocatalyst for the degradation of TC. PS-CDs' dual functionality provides an effectual method for the simultaneous detection and degradation of TC by a single nanoprobe.

Room-Temperature Synthesis of Carbon Dot/TiO2 Composites with High Photocatalytic Activity

Benefiting from the wide-range absorption and adjustable energy gap, carbon dots (C-dots) have attracted a great deal of attention and they have been used to sensitize semiconductor nanocomposites to boost the efficiency of energy conversion devices, while there is still a lack of fundamental understanding of the interaction between such materials and their influence on the catalytic activity on the reaction process. In this study, C-dots were used to modify TiO₂ to form a direct Z-scheme (DZS) junction for enhancement of the photocatalytic activity. The C-dot/TiO₂ composite was prepared by ultrasonication at room temperature through coupling between the Ti-O-C bond and electrostatic interaction. The C-dots can dramatically enhance the absorption of the composite by forming the DZS, and the composite is enabled to generate more free radicals, which facilitate ∼10 times higher photocatalytic activity compared to that of TiO₂. As a proof of concept, the as-prepared C-dot/TiO₂ was used for textile wastewater dye degradation. This study provides an efficient approach for room-temperature preparation of C-dot/TiO₂ composites with high photocatalytic activity.

Utilization of metal industry solid waste as an adsorbent for adsorption of anionic and cationic dyes from aqueous solution through the batch and continuous study

Industrial waste, for instance, textile effluents when released into the ecological system without first being treated or with inappropriate levels of treatment, can lead to serious issues deteriorating the environment and human health. Moreover, solid waste from various industries has also become a major issue due to massive urbanization. For instance, the waste from the metal industry has been rapidly increasing such as Jarosite which has various metals, metal oxides, and silica in its composition. Therefore, Jarosite was utilized as an adsorbent for the adsorption of anionic Congo red (CR) and cationic Methylene blue (MB) dyes from aqueous solutions. The processed adsorbent sample was characterized by BET, XRD, SEM, EDS, FTIR, and XPS techniques. The effects of initial dye concentration, pH, adsorbent dose, temperature, and contact time were examined. The metal industry waste is used as a low-cost abundant adsorbent with great potential for adsorption ability to remove the CR (97.5%) and MB (68.5%) at pH 7, contact time 90 min, adsorbent dose 0.1 g, and initial dye concentration 50 mg/L. The adsorption data followed the adsorption isotherm and Kinetics for both dyes. The removal of both dyes was a physical adsorption process, endothermic and spontaneous reaction. Column adsorption investigation was described by AB (Adams-Bohart) and YN (Yoon-Nelson) models. According to the economic view, the utilization of jarosite for dye removal is a cost-effective approach, because it is collected free of cost from industries. Henceforth, for the first time, toxic metal industry waste was successfully utilized as an adsorbent for wastewater treatment.

Non-toxic and biodegradable κ-carrageenan/ZnO hydrogel for adsorptive removal of norfloxacin: Optimization using response surface methodology

Antibiotic resistance is increasing globally due to increased prescription and easy dispensing of antibiotic drugs universally. Hence, to mitigate this effect, efficient, biodegradable, and non-toxic adsorbents are required to be developed. Carrageenan (CG), a natural polymer, having multiple functional groups, provides a backbone for crosslinking with borax and incorporation of ZnO nanoparticles that formed borax-cross-linked κ-carrageenan (CG/Bx/ZnO) hydrogel which is used for efficient adsorption of norfloxacin from water. Surface morphology of as-synthesized hydrogel revealed the rough surface, which was determined by FESEM. Surface area of CG/Bx/ZnO hydrogel was found to be 22.90 m²/g with 3.41 nm pore radius. Systematic batch adsorption studies revealed that 99.4 % removal efficiency could be achieved at a dosage level of 20 mg/L of norfloxacin with 10 mg of hydrogel at pH of 4 in 8 h at room temperature. Experimentally optimized key parameters affecting the overall efficiency of adsorption matched well with the results assessed from ANOVA using Box-Behnken composite design model. The adsorption process was well fitted with the pseudo-second-order model and Langmuir isotherm with 1282.05 mg/g adsorption capacity. Thermodynamic study results show that adsorption is spontaneous and endothermic. The CG/Bx/ZnO hydrogel demonstrated excellent repeatability with minimal loss in norfloxacin adsorption for seven cycles.

Sustainable carbon nano-onions as an adsorbent for the efficient removal of oxo-anions

The increasing threats of oxo-anions in drinking water have posed a serious threat to human health, aquatic environment, ecology, and sustainability. Accordingly, developments of cost-effective and sustainable nanomaterials for water remediation are on top priority and highly sought in global research community. Carbon nano-onions (CNOs) are one of the emerging nanomaterials for water purification because of its unique morphology, surface reactivity, high density of surface-active sites, and microporous structure. Herein, flaxseed oil-derived CNOs are utilized as efficient adsorbent for the removal of toxic oxo-anions. Aside from the green and economic nature, CNOs provide high adsorption efficiency ~ 806.45 mg g^-1 for the removal of [Formula: see text] (99.9%) from aqueous system at ambient temperature, neutral pH in 70 min. The adsorption of [Formula: see text] onto CNOs was well fitted in pseudo-second order kinetics and followed the Langmuir adsorption isotherm model. The adsorption process was determined to be exothermic and spontaneous from the resulting thermodynamic characteristics. Furthermore, the high hydrophobic nature of CNOs make it recycling simpler. The real-life applicability of CNOs towards [Formula: see text] removal was tested in tap water, river water, and dam water. With all these observed results, CNOs show promise for practical water remediation applications.