Automatic estimation of the aortic lumen geometry by ellipse tracking

Segment aorta and localize landmarks simultaneously on noncontrast CT using a multitask learning framework for patients without severe vascular disease

BACKGROUND

Non-contrast chest CT is widely used for lung cancer screening, and its images carry potential information of the thoracic aorta. The morphological assessment of the thoracic aorta may have potential value in the presymptomatic detection of thoracic aortic-related diseases and the risk prediction of future adverse events. However, due to low vasculature contrast in such images, visual assessment of aortic morphology is challenging and highly depends on physicians' experience.

PURPOSE

The main objective of this study is to propose a novel multi-task framework based on deep learning for simultaneous aortic segmentation and localization of key landmarks on unenhanced chest CT. The secondary objective is to use the algorithm to measure quantitative features of thoracic aorta morphology.

METHODS

The proposed network is composed of two subnets to carry out segmentation and landmark detection, respectively. The segmentation subnet aims to demarcate the aortic sinuses of the Valsalva, aortic trunk and aortic branches, whereas the detection subnet is devised to locate five landmarks on the aorta to facilitate morphology measures. The networks share a common encoder and run decoders in parallel, taking full advantage of the synergy of the segmentation and landmark detection tasks. Furthermore, the volume of interest (VOI) module and the squeeze-and-excitation (SE) block with attention mechanisms are incorporated to further boost the capability of feature learning.

RESULTS

Benefiting from the multitask framework, we achieved a mean Dice score of 0.95, average symmetric surface distance of 0.53 mm, Hausdorff distance of 2.13 mm for aortic segmentation, and mean square error (MSE) of 3.23 mm for landmark localization in 40 testing cases.

CONCLUSION

We proposed a multitask learning framework which can perform segmentation of the thoracic aorta and localization of landmarks simultaneously and achieved good results. It can support quantitative measurement of aortic morphology for further analysis of aortic diseases, such as hypertension.

Assessment of fully automatic segmentation of pulmonary artery and aorta on noncontrast CT with optimal surface graph cuts

Purpose

Accurate segmentation of the pulmonary arteries and aorta is important due to the association of the diameter and the shape of these vessels with several cardiovascular diseases and with the risk of exacerbations and death in patients with chronic obstructive pulmonary disease. We propose a fully automatic method based on an optimal surface graph‐cut algorithm to quantify the full 3D shape and the diameters of the pulmonary arteries and aorta in noncontrast computed tomography (CT) scans.

Methods

The proposed algorithm first extracts seed points in the right and left pulmonary arteries, the pulmonary trunk, and the ascending and descending aorta by using multi‐atlas registration. Subsequently, the centerlines of the pulmonary arteries and aorta are extracted by a minimum cost path tracking between the extracted seed points, with a cost based on a combination of lumen intensity similarity and multiscale medialness in three planes. The centerlines are refined by applying the path tracking algorithm to curved multiplanar reformatted scans and are then smoothed and dilated nonuniformly according to the extracted local vessel radius from the medialness filter. The resulting coarse estimates of the vessels are used as initialization for a graph‐cut segmentation. Once the vessels are segmented, the diameters of the pulmonary artery (PA) and the ascending aorta (AA) and the PA:AA ratio are automatically calculated both in a single axial slice and in a 10 mm volume around the automatically extracted PA bifurcation level. The method is evaluated on noncontrast CT scans from the Danish Lung Cancer Screening Trial (DLCST). Segmentation accuracy is determined by comparing with manual annotations on 25 CT scans. Intraclass correlation (ICC) between manual and automatic diameters, both measured in axial slices at the PA bifurcation level, is computed on an additional 200 CT scans. Repeatability of the automated 3D volumetric diameter and PA:AA ratio calculations (perpendicular to the vessel axis) are evaluated on 118 scan–rescan pairs with an average in‐between time of 3 months.

Results

We obtained a Dice segmentation overlap of 0.94 ± 0.02 for pulmonary arteries and 0.96 ± 0.01 for the aorta, with a mean surface distance of 0.62 ± 0.33 mm and 0.43 ± 0.07 mm, respectively. ICC between manual and automatic in‐slice diameter measures was 0.92 for PA, 0.97 for AA, and 0.90 for the PA:AA ratio, and for automatic diameters in 3D volumes around the PA bifurcation level between scan and rescan was 0.89, 0.95, and 0.86, respectively.

Conclusion

The proposed automatic segmentation method can reliably extract diameters of the large arteries in non‐ECG‐gated noncontrast CT scans such as are acquired in lung cancer screening.

Deep learning method for aortic root detection

BACKGROUND

Computed tomography angiography (CTA) is a preferred imaging technique for a wide range of vascular diseases. However, extensive manual analysis is required to detect and identify several anatomical landmarks for clinical application. This study demonstrates the feasibility of a fully automatic method for detecting the aortic root, which is a key anatomical landmark in this type of procedure. The approach is based on the use of deep learning techniques that attempt to mimic expert behavior.

METHODS

A total of 69 CTA scans (39 for training and 30 for validation) with different pathology types were selected to train the network. Furthermore, a total of 71 CTA scans were selected independently and applied as the test set to assess their performance.

RESULTS

The accuracy was evaluated by comparing the locations marked by the method with benchmark locations (which were manually marked by two experts). The interobserver error was 4.6 ± 2.3 mm. On an average, the differences between the locations marked by the two experts and those detected by the computer were 6.6 ± 3.0 mm and 6.8 ± 3.3 mm, respectively, when calculated using the test set.

CONCLUSIONS

From an analysis of these results, we can conclude that the proposed method based on pre-trained CNN models can accurately detect the aortic root in CTA images without prior segmentation.

A fully automated pipeline for mining abdominal aortic aneurysm using image segmentation

Imaging software have become critical tools in the diagnosis and the treatment of abdominal aortic aneurysms (AAA). The aim of this study was to develop a fully automated software system to enable a fast and robust detection of the vascular system and the AAA. The software was designed from a dataset of injected CT-scans images obtained from 40 patients with AAA. Pre-processing steps were performed to reduce the noise of the images using image filters. The border propagation based method was used to localize the aortic lumen. An online error detection was implemented to correct errors due to the propagation in anatomic structures with similar pixel value located close to the aorta. A morphological snake was used to segment 2D or 3D regions. The software allowed an automatic detection of the aortic lumen and the AAA characteristics including the presence of thrombus and calcifications. 2D and 3D reconstructions visualization were available to ease evaluation of both algorithm precision and AAA properties. By enabling a fast and automated detailed analysis of the anatomic characteristics of the AAA, this software could be useful in clinical practice and research and be applied in a large dataset of patients.