Adsorption and precipitation of anionic dye Reactive Red 120 from aqueous solution by aminopropyl functionalized magnesium phyllosilicate

Modified Halloysite as an Adsorbent for the Removal of Cu(II) Ions and Reactive Red 120 Dye from Aqueous Solutions

The adsorption of copper ions and Reactive Red 120 azo dye (RR-120) as models of water pollutants on unmodified halloysite (H-NM), as well as halloysites modified with sulfuric acid (H-SA) and (3-aminopropyl)triethoxysilane (H-APTES), was investigated. The results showed that adsorption of both the adsorbates was pH-dependent and increased with the increase in halloysite dosage. The adsorption kinetics were evaluated and the results demonstrated that the adsorption followed the pseudo-second-order model. The adsorption isotherms of Cu(II) ions and RR-120 dye on the halloysites were described satisfactorily by the Langmuir model. The maximum adsorption capacities for the Cu(II) ions were 0.169, 0.236, and 0.507 mmol/g, respectively, for H-NM, H-SA, and H-APTES indicating that the NH2-functionalization rather than the surface area of the adsorbents was responsible for the enhanced adsorption. The adsorption capacities for RR-120 dye were found to be 9.64 μmol/g for H-NM, 75.76 μmol/g for H-SA, and 29.33 μmol/g for H-APTES. The results demonstrated that APTES-functionalization and sulfuric acid activation are promising modifications, and both modified halloysites have good application potential for heavy metals as well as for azo dye removal.

Controversial Issues Related to Dye Adsorption on Clay Minerals: A Critical Review

This critical review points out the most serious and problematic issues to be found in the literature on the adsorption of dyes on clay minerals. The introduction draws attention to the fundamental problems, namely the insufficient characterization of adsorbents, the influence of impurities on the adsorption of dyes, and the choice of inappropriate models for the description of the very complex systems that clay minerals and their systems represent. This paper discusses the main processes accompanying adsorption in colloidal systems of clay minerals. The relationship between the stability of the colloidal systems and the adsorption of dye molecules is analyzed. The usual methodological procedures for determining and evaluating the adsorption of dyes are critically reviewed. A brief overview and examples of modified clay minerals and complex systems for the adsorption of organic dyes are summarized. This review is a guide for avoiding some faults in characterizing the adsorption of organic dyes on clay minerals, to improve the procedure for determining adsorption, to evaluate results correctly, and to find an appropriate theoretical interpretation. The main message of this article is a critical analysis of the current state of the research in this field, but at the same time, it is a guide on how to avoid the most common problems and mistakes.

Recyclable magnetic Fe3O4@C for methylene blue removal under microwave-induced reaction system

The reclamation and removal of organic pollutants are difficult issues of world concern. In this study, a microwave-induced reaction system (MIRS) is applied to synthesize the multifunctional composite of Fe₃O₄@C, which is employed to adsorb, separate and catalytic oxide the typical organic dye of methylene blue (MB). SEM, TEM, VSM, XPS, pHpzc, and N₂ adsorption performances are carried out to characterize the Fe₃O₄@C. Results show that the Fe₃O₄@C mainly consists of activated Fe-O-C microspheres, which possess plentiful mesopore and macropore structures on surfaces. Batch adsorption experiments were carried out by varying key reaction conditions to optimize these. The maximum adsorption capacity of MB onto the Fe₃O₄@C was 305.0 mg g^-1 in 120 min, at pH 10, and at a temperature of 323 K. MIRS was also assisted to regenerate the spent Fe₃O₄@C which presented good regeneration efficiency by sustaining 16 regeneration cycles without any oxidizing agent. SEM images and FTIR spectrum verified that MB would translate into greater or smaller-sized carbon microspheres. What's more, the adsorption of MB onto both initial and the 16th regenerated Fe₃O₄@C obeyed the Langmuir isotherm model and followed the pseudo-second-order adsorption kinetics, indicating the adsorptive stability after regeneration. In this study, the Fe₃O₄@C combined with MIRS may be one innovative strategy for organic pollutants' complete removal in the future.

Enhanced photocatalytic degradation of Reactive Red 120 dye under solar light using BiPO4@g-C3N4 nanocomposite photocatalyst

Azo dyes such as Reactive Red 120 raise great concerns about their increased harmfulness. Photocatalytic degradation is considered to be one of the most efficient techniques for Reactive Red 120 degradation. Herein, a highly solar active graphitic carbon nitride-assisted bismuth phosphate nanocomposite (BiPO₄@g-C₃N₄) was synthesized by the thermal decomposition of melamine followed by the co-precipitation method. Various analytical techniques were utilized to characterize the prepared BiPO₄, g-C₃N₄, and BiPO₄@g-C₃N₄ nanocomposites. Scanning electron microscopy (SEM) shows the nanorods and particle morphology of the bare BiPO₄ and g-C₃N₄ respectively. Furthermore, the optical band gap energies of the BiPO₄, g-C₃N₄, and BiPO₄@g-C₃N₄ nanocomposite have been calculated to be 4.20, 2.66, and 2.68 eV respectively. Under sunlight, the BiPO₄@g-C₃N₄ nanocomposite showed higher photocatalytic activity towards the degradation of RR120. The BiPO₄@g-C₃N₄ nanocomposite efficiently degrades the RR120 under sunlight with a higher first-order reaction rate constant of 0.0145 min^-1. This is seven times higher than that of bare BiPO₄ (0.0019 min^-1) nanorods and four times greater than g-C₃N₄ (0.0036 min^-1). The photocatalytic efficiency was found to be maximum at pH 4 and decreased as the pH of the solution increased. Even after five recycle runs, the catalyst performance of the RR120 dye has decreased by less than 5%, indicating the high stability of the BiPO₄@g-C₃N₄ nanocomposite. Furthermore, the radical trapping experiment demonstrates that the active species in the dye degradation process are holes and hydroxide radicals. The photocatalytic mechanism was proposed for the BiPO₄@g-C₃N₄ nanocomposite and further validated by the electrochemical impedance spectroscopy analysis.

Synthesis of high surface area mesoporous ZnCl2–activated cocoa (Theobroma cacao L) leaves biochar derived via pyrolysis for crystal violet dye removal

Chemically activated cocoa leaves biochar (CLB) was successfully prepared from fallen cocoa leaves (CLs) via ZnCl₂–activation and pyrolysis at 700 °C for sequestration of toxic crystal violet (CV) dye from aqueous solution. CLs and CLB were characterized using elemental analysis (CHN/O), Brunauer-Emmett-Teller method (BET), thermogravimetric analysis (TGA), Fourier transform infrared (FTIR), X-ray diffraction (XRD) spectroscopy and scanning electron microscopy (SEM). The optimum conditions for effective removal of CV dye from aqueous solution (75.67% for CLs and 99.87% for CLB) were pH 9, initial CV dye concentration 100 mg/L, adsorbent (CLs/CLB) dose 0.4 g/L, contact time 160 min and temperature 300 K. Modified Ritchie second order best described kinetic and Liu model described equilibrium adsorption. CLs and CLB with maximum adsorption capacities 190.70 and 253.3 mg/g respectively, compete favorably with adsorbents used for removal of CV dye from wastewater in the literature. The high BET surface area (957.02 m²/g) and mean pore diameter (7.21 nm) were indicators of better adsorption efficiency of CLB. CLs showed adsorption to proceed towards endothermic process, while it was exothermic process for CLB. This study established the suitability of cocoa leaves as sustainable and environmental friendly precursor for preparation of adsorbent for the treatment of dye-containing wastewater.

Magnesium/aluminum layered double hydroxides intercalated with starch for effective adsorptive removal of anionic dyes

In this research, the adsorptive performance of a starch-magnesium/aluminum layered double hydroxide (S-Mg/Al LDH) composite was investigated for different organic dyes in single-component systems by conducting a series of batch mode experiments. S-Mg/Al LDH composite showed preferential adsorption of anionic dyes than cationic dyes. The marked impact of key process variables (e.g., contact time, adsorbent dosage, pH, and temperature) on its adsorption was investigated. Multiple isotherms, kinetics, and thermodynamic models were applied to describe adsorption behavior, diffusion, and uptake rates of the organic dyes over S-Mg/Al LDH composite. A better fitting of the non-linear Langmuir model reflects the predominance of monolayered adsorption of dye molecules on the composite surface. Partition coefficients (mg g^-1 μM^-1) for S-Mg/Al LDH were observed in the following descending order: Amaranth (665) > Tartrazine (186) > Sunset yellow (71) > Eosin yellow (65). Furthermore, comparative evaluation of the adsorption enthalpy, entropy, and Gibbs free energy values indicates that the adsorption process is spontaneous and exothermic. S-Mg/Al LDH composite maintained a stable adsorption/desorption recycling process over six consecutive cycles with the advantages of low cost, chemical/mechanical stability, and easy recovery. The results of this study are expected to expand the application of modified LDHs toward wastewater treatment.

Copper Phyllosilicates-Derived Catalysts in the Production of Alcohols from Hydrogenation of Carboxylates, Carboxylic Acids, Carbonates, Formyls, and CO2: A Review

Copper phyllosilicates-derived catalysts (CuPS-cats) have been intensively explored in the past two decades due to their promising activity in carbonyls hydrogenation. However, CuPS-cats have not been completely reviewed. This paper focuses on the aspects concerning CuPS-cats from synthesis methods, effects of preparation conditions, and dopant to catalytic applications of CuPS-cats. The applications of CuPS-cats include the hydrogenation of carboxylates, carboxylic acids, carbonates, formyls, and CO2 to their respective alcohols. Besides, important factors such as the Cu dispersion, Cu+ and Cu0 surface areas, particles size, interaction between Cu and supports and dopants, morphologies, and spatial effect on catalytic performance of CuPS-cats are discussed. The deactivation and remedial actions to improve the stability of CuPS-cats are summarized. It ends up with the challenges and prospective by using this type of catalyst.

Synthesis and characterization of Ni-doped anatase TiO2 loaded on magnetic activated carbon for rapidly removing triphenylmethane dyes

In this work, we employed the in situ synthesis method to implant Fe₃O₄ into activated carbon (AC), in which the synthesis of the magnetic AC (MAC) was realized. Thence, Ni-doped anatase TiO₂ (NATiO₂) were anchored on different addition amount of MAC to synthesize the series of Ni-TiO₂/MAC photocatalysts. The chemical compositions and physical properties of these nanocomposites were analyzed by various characterization technologies. The photocatalytic capabilities of as-produced materials were then investigated via adsorption and photodegradation of triphenylmethane dyes (TPMs) as crystal violet (CV), basic fuchsine (BF), and malachite green (MG) solution. The results revealed that the removal of Ni-TiO₂/AC, Ni-TiO₂/2MAC, Ni-TiO₂/4MAC, and Ni-TiO₂/8MAC on TPMs is a very fast process and the removal efficiency can almost reach to about 90% in 10 min, and the catalyst has good cycle stability and is easy to be reused. This work provides a novel, low-cost, and effective way to rationally design and synthesize TiO₂-based photocatalysts for effective removal of TPMs.