Molecularly Imprinted Supermacroporous Cryogels for Myoglobin Recognition

Capacity of Infusion Lines for Insulin Adsorption: Effect of Flow Rate on Total Adsorption

BACKGROUND

Insulin adsorption to clinical materials has been well observed, but not well quantified. Insulin adsorption reduces expected and actual insulin delivery and is unaccounted for in insulin therapy or glycemic control. It may thus contribute to poor control and high glycemic variability. This research quantifies the problem in the context of clinical use.

METHOD

Experimental insulin adsorption data from literature is used to calculate insulin delivery and total insulin adsorption capacities for polyethylene (PE) and polyvinal chloride (PVC) lines at clinically relevant flow rates and concentrations.

RESULTS

Insulin adsorption capacity decreased hyperbolically with flow rate for both PE and PVC, where low flow scenarios result in greater insulin adherence to infusion lines. When the infusion flow rate was halved from 1 to 0.5 mL/h, twice as much insulin adsorbed to the line. Insulin loss to adsorption resulted in up to ~50% of intended insulin not delivered over 24 hours in a low flow and low concentration context.

CONCLUSION

Material capacity for insulin adsorption is not constant, but increases with decreasing flow. Different materials have different adsorption capacities. In low flow and low concentration contexts, such as in neonatal or pediatric intensive care, insulin loss to adsorption represents a significant proportion of daily insulin delivery, which needs to be accounted for.

Evaluation of Molecularly Imprinted Polymers for Point-of-Care Testing for Cardiovascular Disease

Molecular imprinting is a rapidly growing area of interest involving the synthesis of artificial recognition elements that enable the separation of analyte from a sample matrix and its determination. Traditionally, this approach can be successfully applied to small analyte (<1.5 kDa) separation/ extraction, but, more recently it is finding utility in biomimetic sensors. These sensors consist of a recognition element and a transducer similar to their biosensor counterparts, however, the fundamental distinction is that biomimetic sensors employ an artificial recognition element. Molecularly imprinted polymers (MIPs) employed as the recognition elements in biomimetic sensors contain binding sites complementary in shape and functionality to their target analyte. Despite the growing interest in molecularly imprinting techniques, the commercial adoption of this technology is yet to be widely realised for blood sample analysis. This review aims to assess the applicability of this technology for the point-of-care testing (POCT) of cardiovascular disease-related biomarkers. More specifically, molecular imprinting is critically evaluated with respect to the detection of cardiac biomarkers indicative of acute coronary syndrome (ACS), such as the cardiac troponins (cTns). The challenges associated with the synthesis of MIPs for protein detection are outlined, in addition to enhancement techniques that ultimately improve the analytical performance of biomimetic sensors. The mechanism of detection employed to convert the analyte concentration into a measurable signal in biomimetic sensors will be discussed. Furthermore, the analytical performance of these sensors will be compared with biosensors and their potential implementation within clinical settings will be considered. In addition, the most suitable application of these sensors for cardiovascular assessment will be presented.

Selective Recognition of Myoglobin in Biological Samples Using Molecularly Imprinted Polymer-Based Affinity Traps

The current work demonstrates the design, characterization, and preparation of molecularly imprinted microspheres for the selective detection of myoglobin in serum samples. The suspension polymerization approach was applied for the preparation of myoglobin imprinted microspheres. For this purpose, N-methacryloylamino folic acid-Nd3+ (MAFol- Nd3+) was chosen as the complex functional monomer. The optimization studies were performed changing the medium pH, temperature, and myoglobin concentration. pH 7.0 was determined as the optimum value where the prepared imprinted microspheres displayed maximum binding for myoglobin. The maximum binding capacity was achieved as 623 mgg-1. In addition, the selectivity studies were conducted. The results confirmed that the imprinted microspheres showed great selectivity towards myoglobin in the existence of hemoglobin, cytochrome c, and lysozyme which were chosen as potentially competing proteins.

Plastic antibodies tailored on quantum dots for an optical detection of myoglobin down to the femtomolar range

A highly sensitive fluorescence detection probe was developed by tailoring plastic antibodies on the external surface of aqueous soluble quantum dots (QDs). The target was Myoglobin (Myo), a cardiac biomarker that quenched the intrinsic fluorescent emission of cadmium telluride (CdTe) QDs capped with mercaptopropionic acid (CdTe-MPA-QDs). The QDs were incubated with the target protein and further modified with a molecularly-imprinted polymer (MIP) produced by radical polymerization of acrylamide and bisacrylamide. The main physical features of the materials were assessed by electron microscopy, dynamic light scattering (DLS), UV/Vis spectrophotometry and spectrofluorimetry. The plastic antibodies enabled Myo rebinding into the QDs with subsequent fluorescence quenching. This QD-probe could detect Myo concentrations from 0.304 to 571 pg/ml (50.6 fM to 95 pM), with a limit of detection of 0.045 pg/ml (7.6 fM). The proposed method was applied to the determination of Myo concentrations in synthetic human serum. The results obtained demonstrated the ability of the modified-QDs to determine Myo below the cut-off values of myocardial infarction. Overall, the nanostructured MIP-QDs reported herein displayed quick responses, good stability and sensitivity, and high selectivity for Myo, offering the potential to be explored as new emerging sensors for protein detection in human samples.

Composite imprinted macroporous hydrogels for haemoglobin purification from cell homogenate

Purification of haemoglobin (Hb) has been studied for many years due to its ability to act as an oxygen carrier and its possible use in urgent clinical treatment. In this study, different types of chromatography columns were developed for Hb purification. Two of them showed satisfactory results as affinity chromatography columns and were thus studied more extensively. The affinity adsorbents were prepared by molecular imprinting techniques. In the first case, Pickering emulsion polymerization was used to prepare affinity adsorbents based on molecular imprinting technology. The imprinted particles were immobilized via covalent bonds on the surface of cryogel, a macroporous hydrogel produced by free radical polymerization under sub-zero temperature. In the second case, the affinity sites for Hb were formed directly on an acrylamide cryogel by protein imprinting during the cryogelation. The dynamic binding capacity of the composite cryogel with the immobilized particles and the directly imprinted acrylamide cryogel was found to be 5.2 mg/g and 3.6 mg/g, respectively. The affinity columns showed high selectivity towards Hb in spite of the presence of serum albumin as well as other interfering substances in non-clarified cell homogenates. The maximum capacity in batch mode, the fluid flow and other physical and chemical properties of these columns were investigated.

A comprehensive review of cryogels and their roles in tissue engineering applications

The extracellular matrix is fundamental in providing an appropriate environment for cell interaction and signaling to occur. Replicating such a matrix is advantageous in the support of tissue ingrowth and regeneration through the field of tissue engineering. While scaffolds can be fabricated in many ways, cryogels have recently become a popular approach due to their macroporous structure and durability. Produced through the crosslinking of gel precursors followed by a subsequent controlled freeze/thaw cycle, the resulting cryogel provides a unique, sponge-like structure. Therefore, cryogels have proven advantageous for many tissue engineering applications including roles in bioreactor systems, cell separation, and scaffolding. Specifically, the matrix has been demonstrated to encourage the production of various molecules, such as antibodies, and has also been used for cryopreservation. Cryogels can pose as a bioreactor for the expansion of cell lines, as well as a vehicle for cell separation. Lastly, this matrix has shown excellent potential as a tissue engineered scaffold, encouraging regrowth at numerous damaged tissue sites in vivo. This review will briefly discuss the fabrication of cryogels, with an emphasis placed on their application in various facets of tissue engineering to provide an overview of this unique scaffold's past and future roles.

STATEMENT OF SIGNIFICANCE

Cryogels are unique scaffolds produced through the controlled freezing and thawing of a polymer solution. There is an ever-growing body of literature that demonstrates their applicability in the realm of tissue engineering as extracellular matrix analogue scaffolds; with extensive information having been provided regarding the fabrication, porosity, and mechanical integrity of the scaffolds. Additionally, cryogels have been reviewed with respect to their role in bioseparation and as cellular incubators. This all-inclusive view of the roles that cryogels can play is critical to advancing the technology and expanding its niche within biomaterials and tissue engineering research. To the best of the authors' knowledge, this is the first comprehensive review of cryogel applications in tissue engineering that includes specific looks at their growing roles as extracellular matrix analogues, incubators, and in bioseparation processes.