Thermo- and sulfate-controllable bioelectrocatalysis of glucose based on horseradish peroxidase and glucose oxidase embedded in poly(N,N-diethylacrylamide) hydrogel films

Precise positioning of enzymes within hierarchical polymer nanostructures for switchable bioelectrocatalysis

The ability to reversibly switch bioelectrocatalytic sensors is attractive for the design of biomonitoring platforms displaying a complex environmental response, or for the protection of biosensors. However, the retention of reversible biocatalytic properties upon multiple environmental cycles, with broad detection range, low signal-to-noise and limit of detection remains challenging. In this report, we demonstrate the precise positioning of the enzyme glucose oxidase within block-copolymer brush nanostructures, via the re-initiation of N-isopropylacrylamide (NIPAM) polymerisation from enzyme-decorated poly(dimethylaminoethyl methacrylate) (PDMAEMA) blocks. We find that the precise design of polymer brush grafting density, thickness and crosslinking of the PNIPAM block enables the stable positioning of biocatalytic sites close to electrode surfaces. The control of the polymer brush nanostructure, its conformation and the distribution of biocatalytic sites is characterised via a combination of in situ ellipsometry, X-ray photoelectron spectroscopy, grazing angle FTIR and surface plasmon resonance. In turn, cyclic voltammetry and electrochemical impedance spectroscopy demonstrate that such control of the polymeric nanostructures confers a unique combination of low limit of detection (23.9 μM), a broad dynamic range of glucose sensing (0.05-12.8 mM) and true "OFF" state upon pH or thermal stimulation, whilst retaining excellent performance over repeated switching cycles of the sensor. Therefore, hierarchical biocatalytic polymer brushes display unique properties for the design of responsive biosensors and complex multi-functional gating platforms.

Electrochemical dopamine sensor based on the use of a thermosensitive polymer and an nanocomposite prepared from multiwalled carbon nanotubes and graphene oxide

An electrochemical dopamine sensor with a temperature-controlled switch was constructed by using a mixture of thermo-sensitive block copolymers (type tBA-PDEA-tBA), graphene oxide (GO) and multi-walled carbon nanotubes (MWCNTs). If the temperature is below 26 °C, the polymer on the glassy carbon electrode (GCE) is stretched, the distance between the MWCNTs is large, and the charge transfer resistance (R_ct) of the composite also is large. In the presence of dopamine, the electron transfer at the electrode is strongly retarded and in the "off" state. At above 38 °C, the polymer is shrunk and the R_ct is much smaller. The presence of dopamine results in a rapid electron transfer at the GCE, and this is referred to as the "on" state. At temperatures between 26 and 38 °C, the polymer shrinks slightly and has a "spring-like" state. There is a linear relationship between the response current (typically measured at a potential as low as 0.16 V vs. Ag/AgCl) and temperature. The response to dopamine is linear in the 0.06 to 4.2 μM and 4.2 to 18.2 μM concentration range, and the detection limit is 42 nM. Conceivably, this approach provides a novel approach towards the design of electrochemical sensors based on the use of thermo-sensitive polymers. Graphical abstract Schematic presentation of reversible and temperature-controlled electrochemical response of dopamine on the thermo-sensitive block copolymers (tBA-PDEA-tBA) / multi-walled carbon nanotubes (MWCNTs) / graphene oxide (GO) / glassy carbon electrode (GCE).

Construction of Multiple Switchable Sensors and Logic Gates Based on Carboxylated Multi-Walled Carbon Nanotubes/Poly(N,N-Diethylacrylamide)

In this work, binary hydrogel films based on carboxylated multi-walled carbon nanotubes/poly(N,N-diethylacrylamide) (c-MWCNTs/PDEA) were successfully polymerized and assembled on a glassy carbon (GC) electrode surface. The electroactive drug probes matrine and sophoridine in solution showed reversible thermal-, salt-, methanol- and pH-responsive switchable cyclic voltammetric (CV) behaviors at the film electrodes. The control experiments showed that the pH-responsive property of the system could be ascribed to the drug components of the solutions, whereas the thermal-, salt- and methanol-sensitive behaviors were attributed to the PDEA constituent of the films. The CV signals particularly, of matrine and sophoridine were significantly amplified by the electrocatalysis of c-MWCNTs in the films at 1.02 V and 0.91 V, respectively. Moreover, the addition of esterase, urease, ethyl butyrate, and urea to the solution also changed the pH of the system, and produced similar CV peaks as with dilution by HCl or NaOH. Based on these experiments, a 6-input/5-output logic gate system and 2-to-1 encoder were successfully constructed. The present system may lead to the development of novel types of molecular computing systems.