The removal of mercury (II) from water by Ag supported on nanomesoporous silica

Novel Carboxylic Acid-Capped Silver Nanoparticles as Antimicrobial and Colorimetric Sensing Agents

The present work reports the synthesis, characterization, and antimicrobial activities of adipic acid-capped silver nanoparticles (AgNPs@AA) and their utilization for selective detection of Hg2+ ions in an aqueous solution. The AgNPs were synthesized by the reduction of Ag+ ions with NaBH4 followed by capping with adipic acid. Characterization of as-synthesized AgNPs@AA was carried out by different techniques, including UV-Visible spectroscopy, Fourier Transform Infrared Spectroscopy (FTIR), Scanning Electron Microscopy (SEM), X-ray diffraction (XRD), Dynamic Light Scattering (DLS), and zeta potential (ZP). In the UV-Vis absorption spectrum, the characteristic absorption band for AgNPs was observed at 404 nm. The hydrodynamic size of as-synthesized AgNPs was found to be 30 ± 5.0 nm. ZP values (-35.5 ± 2.4 mV) showed that NPs possessed a negative charge due to carboxylate ions and were electrostatically stabilized. The AgNPs show potential antimicrobial activity against clinically isolated pathogens. These AgNPs were found to be selectively interacting with Hg2+ in an aqueous solution at various concentrations. A calibration curve was constructed by plotting concentration as abscissa and absorbance ratio (AControl - AHg/AControl) as ordinate. The linear range and limit of detection (LOD) of Hg2+ were 0.6-1.6 μM and 0.12 μM, respectively. A rapid response time of 4 min was found for the detection of Hg2+ by the nano-probe. The effect of pH and temperature on the detection of Hg2+ was also investigated. The nano-probe was successfully applied for the detection of Hg2+ from tap and river water.

A Survey on Nanotechnology-Based Bioremediation of Wastewater

Rainwater discharge and human impacts produce wastewater, which is a contaminated type of water. Sediments also discharge phosphate into the water column when there is a lack of dissolved oxygen in the water. Through the manufacturing of environmentally benign nanoparticles, nanotechnology may reduce the amount of money spent by enterprises to remediate such contaminants. Because of their improved physiological, biochemical, and biomechanical qualities, nanoparticles are getting prominence. The importance of the global wastewater dilemma is discussed in this survey. The use of nanomaterials in heavy metal remediation (HMR) and wastewater treatment is covered in this survey. This paper also discusses the benefits of nanotechnology over traditional approaches in certain fields. This survey aims to gather together many recent studies on nanoparticle production and their benefits as adsorbents in the remediation of wastewater which have been done so far. The promising role of nanotechnology in wastewater remediation is surveyed in this research, which also discusses recent developments in nanotechnology-mediated remediation methods. This survey examines the vital potential of nanotechnology in wastewater treatment, as well as recent breakthroughs in nanotechnology-mediated treatment systems.

Calcium Alginate Beads with Entrapped Iron Oxide Magnetic Nanoparticles Functionalized with Methionine-A Versatile Adsorbent for Arsenic Removal

A novel beads adsorbent, consisting of calcium alginate entrapped on magnetic nanoparticles functionalized with methionine (MFMNABs), was developed for effective elimination of arsenic from water. The material was characterized by FT-IR (Fourier Transform Infrared Spectroscopy), SEM (Scanning Electron Microscopic), XRD (X-ray Diffraction) and TEM (Transmission Electron Microscopy). The arsenic removal capacity of the material was studied by altering variables such as pH of the solution, contact time, adsorbent dose and adsorbate concentration. The maximal removal of As(III) was 99.56% under optimal conditions with an equilibrium time of 110 min and pH 7.0–7.5. The adsorption followed a second order kinetics and data best fitted the Langmuir isotherm with a correlation coefficient of R² = 0.9890 and adsorption capacity (q_m) of 6.6533 mg/g. The thermodynamic study showed entropy change (∆S) and enthalpy change (∆H) to be 34.32 J mol⁻¹ K and 5.25 kJ mol⁻¹, respectively. This study proved that it was feasible to treat an As(III) solution with MFMNABs. The synthesized adsorbent was cost-effective, environmentally friendly and versatile, compared to other adsorbents. The adsorption study was carried by low cost spectrophotometric method using N- bromosuccinimide and rhodamine-B developed in our laboratory.

Sonochemical synthesis of aluminium and aluminium hybrids for remediation of toxic metals

Spherical shaped nano-size aluminium oxide and its hybrids with indole and indole derivatives have been synthesized using sol-gel and post grafting methods coupled with sonication (Branson Digital SonifierS-250D; 20 kHz; 40%) for the remediation of toxic metals (lead and mercury). Different spectroscopic techniques (FTIR, SEM, BET, XRD, and XPS) have been applied to assess the properties of synthesized aluminium oxide and its hybrids. FTIR spectra showed the absorption bands of aluminium oxide (Al-O-Al) and aluminium hybrids (Al-O-C) at 800-400 cm-1 and 1650-1100 cm-1 region, respectively. SEM showed spherical shaped clusters of aluminium oxide which changed into the net-shape structure after the hybrid synthesis. It is worth noting that sonication energy increases the total surface area of aluminium oxide when it gets hybridized with indole and its derivatives from 82 m2/g to 167 m2/g; it also improved the product yield from 68% to 78%. Simultaneously, FTIR, SEM and BET analysis of non-sonicated aluminium oxide and its hybrids were also recorded for comparison. While XRD and XPS analysis were only conducted for sonicated aluminium oxide and its hybrids to manifest the structural and compositional properties. XRD patterns indexed as the cubic crystal system with an average 41 nm crystallite size of sonicated aluminium oxide which remains unaffected after hybrid synthesis. A survey scan under XPS confirmed the presence of all expected elements (aluminium, oxygen, carbon, nitrogen) and deconvolution of each recorded peak showed binding of element with its neighboring elements. The performance of aluminium oxide and its hybrids synthesize with and without sonication are also evaluated using a time-dependent batch adsorption protocol optimize for one hour. The maximum adsorption of lead (37%) and mercury (40%) are found onto sonicated aluminium oxide. The sonicated aluminium hybrids showed 43-63% of lead and 55-67% of mercury at pH 7. The fitness of experimental data using adsorption kinetics and isotherms revealed that adsorption follows Pseudo-second-order kinetic, Langmuir, and Freundlich isotherms.

Efficient Removal of Heavy Metals from Aqueous Solutions Using a Bionanocomposite of Eggshell/Ag-Fe

Eggshell and an easily synthesized bionanocomposite of eggshell with Ag-Fe nanoparticles demonstrated to be efficient adsorbent materials for the removal of lead, arsenic, and mercury from water. The natural material and the bionanocomposite were characterized by TEM and XRD. Ag-Fe nanoparticles vary from 1 to 100 nm in size. Equilibrium times of the adsorption systems were achieved between 4 and 8 h. The experimental adsorption data fitted the pseudo-second and Elovich models; therefore, the adsorption of heavy metals ions took place mainly by a chemical process. The adsorption capacity of eggshell in mg/g was 7.01 for As5+, 3.90 for Pb2+, and 1.51 for Hg2+, while the nanocomposite adsorption capacity was 17.7 for As5+, 27.8 for Pb2+ and 15.88 for Hg2+.

Ultrasonic-assisted recycling of Nile tilapia fish scale biowaste into low-cost nano-hydroxyapatite: Ultrasonic-assisted adsorption for Hg2+ removal from aqueous solution followed by "turn-off" fluorescent sensor based on Hg2+-graphene quantum dots

This study was planned to recycle calcium and the phosphorus-rich Nile tilapia fish scale biowaste into nano-hydroxyapatite (FHAP), using ultrasonic-assisted extraction of calcium and phosphorus from fish scales, which was optimized in term of extraction time, acid concentration, extraction temperature, and ultrasonic power. These two elements were determined simultaneously by inductively coupled plasma atomic emission spectrometry and the FHAP phase was formed upon addition of the extracted element solution in alkaline medium using homogenous precipitation assisted with ultrasound energy. The FHAP adsorbent was characterized by x-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, and Brunauer-Emmett-Teller. A combination of FHAP and the ultrasonic method was then used to remove Hg²⁺ from aqueous solution. Four significant variables affecting Hg²⁺ removal, namely, adsorbent dosage, pH, ultrasonic power, and adsorption time, were studied. The results exhibited that the optimal conditions for maximizing the removal of Hg²⁺ were 0.02 g adsorbent dosage, pH 8, 0.4 kW ultrasonic power, 20 min adsorption time, and 30 °C adsorption temperature. The sorption mechanism of Hg²⁺ was revealed by isotherm modeling, indicating that FHAP adsorbent has a potential for Hg²⁺ removal in aqueous media with the maximum adsorption capacity being 227.27 mg g^-1. This adsorption behavior is in agreement with the Langmuir model as reflected by a satisfactory R² value of 0.9967, when the kinetics data were fitted with pseudo-second-order. Therefore, the FHAP could be an alternative adsorbent for the ultrasonic-assisted removal of Hg²⁺ at very high efficiency and within a very short period of time.

A selective and easily recyclable dimer based on a calix[4]pyrrole derivative for the removal of mercury(ii) from water

A recyclable mercury(ii) selective dimer based on a calix[4]pyrrole derivative has been synthesised and characterised by mass and FT-IR spectrometry, Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray (EDX). Information regarding the ability of the dimer to interact with metal cations was obtained from FTIR and SEM-EDX analyses. A striking feature of micrographs of the loaded dimer is the change of morphology with the cation. Based on these results, optimal conditions for removing cations from water were assessed under different experimental conditions. Results obtained demonstrate that the removal process is fast. Capacity values and selectivity factors show that the dimer is selective for Hg(ii) in single and multiple component metal solutions relative to other cations. Single-ion transfer Gibbs energies from water to a solvent containing common functionalities to those of the dimer were used to assess the counter-ion effect on the removal process. Agreement is found between these data and energy calculations derived from molecular simulation studies. Studies on polluted water in the presence of normal water components in addition to toxic metal cations are reported. Further experimental work on wastewater from the mining industry is in progress.

Silver/quartz nanocomposite as an adsorbent for removal of mercury (II) ions from aqueous solutions

Silver nanoparticles (AgNPs) and silver/quartz nanocomposite (Ag/Q)NPs)) were synthesized by sol-gel method using table sugar as chelating agent. The synthesized nanosized materials were used for mercury ions adsorption from aqueous solutions. The materials were characterized by X-ray diffraction (XRD), Transmission Electron microscope (TEM), and surface area (BET). Adsorption of Hg²⁺ (10 mg/l) is strongly dependent on time, initial metal concentration, dose of adsorbent and pH value. Silver/quartz nanocomposite ((Ag/Q)NPs)) shows better efficiency than individual silver nanoparticles (AgNPs). This composite removed mercury ions from the aqueous solution with efficiency of 96% at 60 min with 0.5g adsorbent dosage at pH 6. The adsorption process explained well by the pseudo-second-order kinetic model. In conclusion silver/quartz nanocomposite (Ag/Q)NPs)) shows higher removal efficiency for mercury ions from aqueous solutions than individual silver naoparticles (AgNPs) or quartz (Q).

Fabrication of novel magnetic graphene oxide nanocomposites for selective adsorption of mercury from aqueous solutions

In this work, a novel functionalized graphene oxide (GO) was used as an effective and selective adsorbent for removal of mercury (Hg²⁺). The magnetic nanocomposite adsorbent (MNA) based on GO was prepared through surface reversible addition-fragmentation chain transfer copolymerization of acrylic monomers and then the formation of Fe₃O₄ nanoparticles. The structure of MNAs was characterized by using FTIR, SEM, TEM, VSM, XRD, and nitrogen adsorption/desorption isotherms. The results of ion adsorption of MNAs demonstrated high selectivity and adsorption efficiency for Hg²⁺ in the presence of competing ions. Furthermore, the removal of Hg²⁺ obeyed a pseudo-second-order model and fitted well to the Langmuir isotherm model with the maximum Hg²⁺ uptake of 389 mg g^-1. The MNA was also confirmed as good materials for re-use and maintained 86% of its initial adsorption capacity for mercury after the fifth regeneration cycles. Finally, the experimental results demonstrated that the solution pH, ion concentration, and temperature had a major impact on Hg(II) adsorption capacity. The results indicate that the MNAs with high adsorption abilities could be very promising adsorbents for the selective recovery of ions in wastewater treatment process. Graphical abstract.

Facile Fabrication of 3D Graphene⁻Silica Hydrogel Composite for Enhanced Removal of Mercury Ions

Adsorption is a highly promising and widely used approach to remove Hg(II) ions from contaminated water. The key to this technology is exploring the effective adsorbent. The three-dimensional (3D) graphene as reduced graphene oxide hydrogel (rGH)-encapsulated silica gel (SG-PEI/rGH) was prepared by a moderate chemical reduction strategy using ascorbic acid. This composite structure was characterized by FTIR, XRD, and SEM analysis and used as adsorbents for Hg(II) ions. Its adsorption capacity toward Hg(II) ions was 266 mg/g and increased about 32% compared with the silica gel because of reduced graphene oxide hydrogel (rGH). Mechanism study showed that the high adsorption ability was due to the formation of an N–Hg complex with multi-amino groups on the surface of polyethyleneimine-modified silica gel (SG-PEI) and the rapid diffusion of adsorbed ions attributed to the rGH network structure. This composite SG-PEI/rGH would be a promising material for the removal of Hg(II) ions.

Phosphonium-based Ionic Liquid Modified Activated Carbon from Mixed Recyclable Waste for Mercury(II) Uptake

The contamination of water surfaces by mercury is a dangerous environmental problem due to its toxicity, which leads kidney damage. Activated carbon from mixed recyclable waste modified by phosphonium-based ionic liquid (IL-ACMRW) was therefore prepared and evaluated for Hg(II) remediation. The activated carbon used in this study was prepared from mixed waste, including cardboard, papers and palm wastes as cheap raw materials. The mixed Recyclable Waste Activated Carbon was combined with trihexyl(tetradecyl)phosphonium Bis2,4,4-(trimethylpentyl)phosphinate (Cyphos^® IL 104) ionic liquid to form an adsorbent with organic-inorganic content, in order to improve the Hg(II) uptake from aqueous solutions. FTIR confirms the presence of P, C=O and OH after this modification. The adsorption process was investigated and the evaluated results showed that the capacity was 124 mg/g at pH 4, with a contact time of 90 min, an adsorbent dose of 0.4 g/L, and a Hg(II) concentration of 50 mg/L. This Hg(II) adsorption capacity is superior than that reported in the literature for modified multiwall carbon nanotubes. The adsorption of Hg(II) on the modified activated carbon from mixed recyclable waste was found to follow the pseudo second-order kinetics model. Isotherms of adsorption were analyzed via Freundlich and Langmuir models. The results indicated that Freundlich is the best model to describe the process, suggesting multilayer adsorption.

Facile and on-line colorimetric detection of Hg2+based on localized surface plasmon resonance (LSPR) of Ag nanotriangles

A rapid and sensitive colorimetric detection method for the determination of Hg²⁺ has been successfully developed in this research. Citrate-functionalized silver nanotriangles (AgTrngs) were synthesized via one-pot sodium borohydride method with the edge-length range of 30 - 40 nm. The obtained AgTrngs were fully characterized using UV-Vis spectrophotometry, transmission electron microscopy (TEM), energy dispersed spectroscopy (EDS) and X-ray diffractometer. The efficiency of the developed sensor was optimum at pH= 8 due to interfering effect of H⁺ ions for Hg²⁺ under acidic conditions. The successful detection of mercury in aqueous solutions in the concentration range of 10 nmol L^-1-50 μmol L^-1 indicated the applicability of the developed sensor for effective monitoring and controlling the level of Hg²⁺ in industrial effluents. The ability of Hg²⁺ ion to interact with Ag and form the Hg-Ag alloy (amalgam) over the surface of AgTrngs resulted in an obvious color change from blue to violet. UV-Vis spectrophotometry showed that the sensor has the limit of detection (LOD) value of as low as 4 nmol L^-1 which was below the safety level of Hg²⁺ions (10 nmol L^-1) in drinking water. The proposed method can be used for on-line determination of Hg²⁺ in the complex aqueous solutions.