Verification of Scherrer formula for well-shaped poly(3-hexylthiophene)-based conductive single crystals and nanofibers and fabrication of photovoltaic devices from thin film coating

Synthesis of Chitosan-TiO2 Nanocomposite for Efficient Cr(VI) Removal from Contaminated Wastewater Sorption Kinetics, Thermodynamics and Mechanism

A photolysis method was used to prepare a nanocomposite adsorbent (Chitosan-TiO₂) and was tested for Cr(VI) removal from aqueous solution. The produce nanocomposite was investigated using, XRD, BET, FTIR, FESEM-EDX and TEM before and after Cr(VI) adsorption. The XRD results shows prepared anatase phase of TiO₂ with 12 nm. According to BET measurements, the surface area of the TiO₂/chitosan nanocomposite was lower and archived to 26 m²/g, while the TEM and FESEM images show a uniform distribution of TiO₂ throughout the chitosan matrix. Adsorption and kinetic experiments were run in batch system under different conditions of pH, contact time, adsorbent dosage and temperature. Experimental Cr(VI) adsorption equilibrium and kinetics data fitted well to Langmuir model. The calculated Langmuir maximum adsorption capacity (q_max) value of nanocomposite was 488 mg/g. Moreover, the highest quantity of Cr(VI) uptake was achieved of pH = 2 and 45℃ and TiO₂ and CS-TiO₂ had respective removal efficiencies of 94 and 87.5%. The thermodynamic parameters of Cr(VI) adsorption by nanocomposite affirm the spontaneous and endothermic nature of process. Chromium adsorption mechanism by CS-TiO₂ nanocomposite were proposed and discussed.

Interfacial and confined molecular-assembly of poly(3-hexylthiophene) and its application in organic electronic devices

Poly(3-hexylthiophene) (P3HT) is a typical conducting polymer widely used in organic thin-film transistors, polymer solar cells, etc., due to good processability and remarkable charging carrier and hole mobility. It is known that the ordered structure assembled by π-conjugated P3HT chains could promote the performance of electronic devices. Interfacial and confined molecular-assembly is one effective way to generate an ordered structure by tuning surface geometry and substrate interaction. Great efforts have been made to investigate the molecular chain assembly of P3HT on a curved surface that is confined to different geometry. In this report, we review the recent advances of the interfacial chain assembly of P3HT in a flat or curved confined space and its application to organic electronic devices. In principle, this interfacial assembly of P3HT at a nanoscale could improve the electronic properties, such as the current transport, power conversion efficiency, etc. Therefore, this review on interfacial and confined assembly of P3HT could give general implications for designing high-performance organic electronic devices.

Photocatalytic Degradation of Wastewater by Molecularly Imprinted Ag2S-TiO2 with High-selectively

The molecular imprinting technique is a new method for preparing molecularly imprinted polymers (MIPs) with specific molecular recognition sites for individual target molecules. In this study, Ag₂S-MIP-TiO₂ nanocomposite was synthesized by a sol-gel-deposition method with ethyl p-hydroxybenzoate as an imprinting molecule. The obtained powder was characterized by XRD and other analytical methods. The results show that the obtained Ag₂S-MIP-TiO₂ nanocomposite demonstrates better catalytic performance than pure anatase TiO₂. The degradation efficiency of ethyl p-hydroxybenzoate during 1.5 h of the photocatalytic reaction is 92.22%, which is 42% higher than pure TiO₂. The selectivity factor for the treatment of ethyl p-hydroxybenzoate compared to phenol using Ag₂S-MIP-TiO₂ reached 3.571, which is 72% higher than pure TiO₂.

Palladium-catalyzed carbene coupling of N-tosylhydrazones and arylbromides to synthesize cross-conjugated polymers

Palladium-catalyzed cross-coupling reactions of N-tosylhydrazones and arylbromides have been applied for the first time in the synthesis of cross-conjugated polymers, namely poly(arylene-1,1-vinylidene)s (iso-PAVs).

Thienoisoindigo-Based Semiconductor Nanowires Assembled with 2-Bromobenzaldehyde via Both Halogen and Chalcogen Bonding

We fabricated nanowires of a conjugated oligomer and applied them to organic field-effect transistors (OFETs). The supramolecular assemblies of a thienoisoindigo-based small molecular organic semiconductor (TIIG-Bz) were prepared by co-precipitation with 2-bromobenzaldehyde (2-BBA) via a combination of halogen bonding (XB) between the bromide in 2-BBA and electron-donor groups in TIIG-Bz, and chalcogen bonding (CB) between the aldehyde in 2-BBA and sulfur in TIIG-Bz. It was found that 2-BBA could be incorporated into the conjugated planes of TIIG-Bz via XB and CB pairs, thereby increasing the π − π stacking area between the conjugated planes. As a result, the driving force for one-dimensional growth of the supramolecular assemblies via π − π stacking was significantly enhanced. TIIG-Bz/2-BBA nanowires were used to fabricate OFETs, showing significantly enhanced charge transfer mobility compared to OFETs based on pure TIIG-Bz thin films and nanowires, which demonstrates the benefit of nanowire fabrication using 2-BBA.