Pharmacokinetic and biodistribution study of eserine and pralidoxime chloride in rabbits following a single application of a transdermal patch

3D Printed Housing Devices for Segregated Compartmental Delivery of Oral Fixed-Dose Anti-Tubercular Drugs Adopting Print and Fill Strategy

World Health Organization (WHO) recommends the use of first-line anti-tuberculosis drugs, that is, rifampicin (RIF) and isoniazid (INH) fixed-dose combination (FDC) therapies in tuberculosis (TB) disease. The absorption of RIF from an FDC incorporates INH, and it is significantly compromised due to its reaction with INH, resulting in a severe loss of RIF under gastric stomach pH condition. Such reduction in the dose of both drugs from FDC formulations has been alleged to be one of the chief obstacles in effective TB treatment. This emphasizes a need to develop suitable cutting-edge advanced bioengineered delivery devices that can attenuate this severe problem to mitigate this chief obstacle. Therefore, we designed, prototyped, and characterized bioengineered 3D printed housing devices in the form of printed tablets adopting print and fill strategy for segregated compartmental delivery of RIF into the intestine (to avoid stomach gastric pH induced chemical degradation as alone and FDC) and INH into the stomach (no degradation observed as alone and FDC in stomach gastric pH conditions) for the desired treatment outcome against TB. Prepared 3D printed housings showed almost zero friability, enough hardness along weight variations <±3.0%. Different thermal and morphological analyses confirmed the insignificant changes in the nature of the polymer as before and after printing. The in vitro release for INH from polyvinyl alcohol mediated 3D printed housings showed almost 100% release within 2.5 h in acidic medium, whereas poly-lactic acid (PLA) mediated 3D printed housings continued to release RIF above 70% in the presence of physiological enzymes in alkaline medium for 432 h. The in vivo bioavailability assessment correlated with in vitro dissolution behavior for INH and RIF, whereas RIF did not release from 3D printed PLA housings in vivo.

Transdermal Delivery of 2-PAM as a Tool to Increase the Effectiveness of Traditional Treatment of Organophosphate Poisoning

For the first time, the efficacy of post-exposure treatment of organophosphate (OP) poisoning was increased by transdermal delivery of acetylcholinesterase (AChE) reactivator pyridine-2-aldoxime methochloride (2-PAM) as a preventive countermeasure. By selecting the optimal ratio of components, classical transfersomes (based on soybean phosphatidylcholine and Tween 20) and modified transfersomes (based on soybean phosphatidylcholine, Tween 20 and pyrrolidinium cationic surfactants with different hydrocarbon tail lengths) were obtained for 2-PAM encapsulation. Transfersomes modified with tetradecylpyrrolidinium bromide showed the best results in encapsulation efficiency and sustained release of 2-PAM from vesicles. Using Franz cells, it was found that the incorporation of surfactants into PC liposomes results in a more prolonged release of 2-PAM through the rat skin. Transfersomes containing 2-PAM, after exhaustive physical and chemical characterization, were embedded in a gel based on Carbopol^® 940. A significantly high degree of erythrocyte AChE reactivation (23 ± 7%) was shown for 2-PAM in unmodified transfersomes in vivo. Preliminary transdermal administration of 2-PAM 24 h before emergency post-exposure treatment of OP poisoning leads to an increase in the survival rate of rats from 55% to 90%.

Customized 3D-printed hollow capsular device filled with norfloxacin-loaded micropellets for controlled-release delivery

Pharmacotherapy has become more focused on the personalized treatment of patients with various diseases. This field of pharmacology and pharmacogenomics focuses on developing drug delivery systems designed to address the unique characteristics of individual patients. Three-dimensional printing technology can be used to fabricate personalized drug delivery systems with desired release properties according to patient needs. Norfloxacin (NOR)-loaded micropellets (MPs) were fabricated and filled inside a stereolithography (SLA) 3D printing technology-mediated hollow capsular device in accordance with a standard size of 09 (8.4 mm length × 2.70 mm diameter). The prepared 3D-printed hollow capsular device filled with pristine NOR and NOR-loaded MPs were characterized in terms of both in vitro and in vivo means. MPs with the particle size distribution of 1540.0 ± 26 µm showed 95.63 ± 2.0% NOR content with pellet-shaped surface morphology. The in vitro release profile showed an initial lag phase of approximately 30 min, followed by the sustained release of NOR from MPs from the 3D-printed hollow capsular device. The pharmacokinetic profile showed prolonged T_max, AUC, and evidence of good RBA of NOR compared to pure NOR after a single oral administration in the experimental animal model. The overall results confirm the feasibility of SLA-mediated 3D printing technology for preparing customized solid oral unit dosage carriers that can be filled with pure NOR- and NOR-loaded MPs with controlled-release delivery features.

Extruded filaments derived 3D printed medicated skin patch to mitigate destructive pulmonary tuberculosis: design to delivery

Background: Quercetin in combination with polyvinylpyrrolidone (PVP) was found to limit the spreading of necrosis to unaffected tissues in tuberculosis-infected mice. Therefore, we hypothesized that 3D printed medicated skin patch incorporated with a quercetin-PVP combination would provide an appropriate therapeutic drug concentration with desired sustained release profile.Research design and methods: We fabricated quercetin-PVP 40 extruded-filaments by hot-melt extrusion (HME) technique along with Eudragit® RSPO and tri-ethyl citrate and further printed it to make medicated skin patches using fused deposition modeling (FDM) based 3D Printing technology. Various characterizations were performed to optimize the 3D-printed patch formulation.Results: Patch formulation has been optimized for several characterization parameters and was further assessed using SEM, DSC, and XRD studies to confirm the conversion of crystalline quercetin into an amorphous form. Finally, the pharmacokinetic profile of an optimized patch was studied in rats showing prolonged T_max, lowered C_max, and reduced fluctuations in plasma concentrations till 18 days with single skin application of 3D-printed medicated patch.Conclusion: Overall data confirmed the feasibility of developing 3D printed medicated skin patches to provide plasma levels for continued 18 days in rats after a single application.