Plasma-Based Ambient Desorption/Ionization Mass Spectrometry for the Analysis of Liquid Crystals Employed in Display Devices

Focusing Plasma Desorption/Ionization Mass Spectrometry

A plasma-based source named focusing plasma desorption/ionization (FPDI) is described, which applies a high direct current voltage between a metal wire inside a polymeric hollow truncated cone and a piece of a one-sided coated conducting paper substrate. The conducting paper acts as both the counter electrode and the sample carrier. Upon the generation of a visible plasma beam, it would directly ionize the samples spotted on the conducting paper substrate or located around the plasma beam. The signal intensity of target analytes in mass spectrometric analysis is dependent highly on whether the conducting paper substrate is grounded or not, the type of conducting paper substrate, the inside diameter of the polymeric hollow truncated cone tip, the metal wire tip-to-polymer tip distance, the polymer tip-to-paper substrate distance, the applied voltage, and the helium flow rate. Based on the experimental observation, a plausible mechanism is proposed for the generation of the plasma beam from FPDI. Compared to the available low-temperature plasma, flowing atmospheric-pressure afterglow, and helium plasma ionization sources, FPDI has demonstrated higher sensitivity and better compatibility with commercial mass spectrometers without any extra power supplies. As a proof of concept, FPDI coupled with a mass spectrometer has also been applied for the discrimination of different brands of gasoline and determination of solid tablets and pesticides with limits of detection in the range of 2.2 to 30.7 ng mL^-1.

Flowing Atmospheric Pressure Afterglow for Ambient Ionization: Reaction Pathways Revealed by Modeling

We describe the plasma chemistry in a helium flowing atmospheric pressure afterglow (FAPA) used for analytical spectrometry, by means of a quasi-one-dimensional (1D) plasma chemical kinetics model. We study the effect of typical impurities present in the feed gas, as well as the afterglow in ambient humid air. The model provides the species density profiles in the discharge and afterglow regions and the chemical pathways. We demonstrate that H, N, and O atoms are formed in the discharge region, while the dominant reactive neutral species in the afterglow are O₃ and NO. He* and He₂* are responsible for Penning ionization of O₂, N₂, H₂O, H₂, and N, and especially O and H atoms. Besides, He₂⁺ also contributes to ionization of N₂, O₂, H₂O, and O through charge transfer reactions. From the pool of ions created in the discharge, NO⁺ and (H₂O)₃H⁺ are the dominant ions in the afterglow. Moreover, negatively charged clusters, such as NO₃H₂O^- and NO₂H₂O^-, are formed and their pathway is discussed as well. Our model predictions are in line with earlier observations in the literature about the important reagent ions and provide a comprehensive overview of the underlying pathways. The model explains in detail why helium provides a high analytical sensitivity because of high reagent ion formation by both Penning ionization and charge transfer. Such insights are very valuable for improving the analytical performance of this (and other) ambient desorption/ionization source(s).

Direct analysis in real time coupled with quadrupole-Orbitrap high-resolution mass spectrometry for rapid analysis of pyrethroid preservatives in wooden food contact materials

A methodology is presented for the determination of four pyrethroid (PYR) preservatives in wooden food contact materials (FCMs) using direct analysis in real time (DART) coupled with quadrupole-Orbitrap high-resolution mass spectrometry (Q-Orbitrap HRMS). The sampling mode and critical parameters of the DART-Q-Orbitrap HRMS protocol were systematically investigated. Good linearity was achieved for the four analytes with correlation coefficients all greater than 0.99. The limits of detection (LODs) and limits of quantitation (LOQs) of the method were in the range of 0.04-0.20 mg kg^-1 and 0.10-0.50 mg kg^-1, respectively. The mean recoveries ranged from 72.1% to 82.7% with relative standard deviations (RSDs) from 5.2% to 11.8% at three spiked levels. The developed method was proved to be suitable for rapid screening of PYRs in complex wooden FCM samples to ensure product safety and consumer health.