Ni and Zn modified acid activated montmorillonite clay for effective removal of carbol fuchsin dye from aqueous solution

The Synthesis of carbon dots//zincoxide (CDs/ZnO-H400) by using hydrothermal methods for degradation of ofloxacin antibiotics and reactive red azo dye (RR141)

The development of photocatalytic powders to remove contaminants from air solutions is an important field of research in the field of environmental conservation. CD/ZnO-H400, a heterogeneous photocatalytic production, is utilized to degrade the reactive red dye and the antibiotic ofloxacin found in wastewater. This study explains the synthesis of carbon dots (CDs) derived from coconut air and zinc oxide (ZnO) using a hydrothermal method at a temperature of 180 °C with a duration of 4 h and subsequently calcinated at a 400 °C temperature for 4 h. This shows a significant improvement in photocatalytic performance due to improved delivery efficiency at the interface. The cost-efficient use of solar energy allows the comprehensive elimination of harmful pollutants through detoxification. The removal of the contaminant takes place through the first-order reaction, with RR141 showing the highest constant rate at 0.03 min-1, while ofloxacin has a constant speed at 0.01 min-1. The photocatalytic stability is measured after five cycles. The study also tested the impact of sunlight on degradation, showing a degrading rate of 98% for RR141 and 96% for ofloxacin. This study displays a new catalyst powder synthesized from carbon dots derived from the air, coconut and ZnO, showing remarkable photoactivity to completely remove harmful dyes and antibiotics from the surrounding environment.

Photodegradation of Carbol Fuchsin Dye Using an Fe2−xCuxZr2−xWxO7 Photocatalyst under Visible-Light Irradiation

Fe2−xCuxZr2−xWxO7 (x: 0, 0.05, 0.015) nanoparticles were synthesized following the Pechini method and characterized via X-ray diffraction (XRD), transmission electron microscopy (TEM), and diffuse reflectance spectroscopy (DRS) measurements to be used as photocatalysts in colored water remediation. All of the prepared materials were crystallized in a cubic fluorite phase as the major phase. The band gap was reduced upon doping with W6+ and Cu2+ from 1.96 eV to 1.47 eV for Fe1.85Cu0.15Zr1.85W0.15O7. Carbol fuchsin (CF) dye was used to determine the photocatalytic degradation efficiency of the prepared catalysts. Degradation efficiency was directly proportional to the dopant’s concentration. Complete removal of 20 mg/L CF was achieved under optimal conditions (pH 9, and catalyst loading of 1.5 g/L) using Fe1.85Cu0.15Zr1.85W0.15O7. The degradation rate followed pseudo-first-order kinetics. The reusability for photocatalysts was tested five times, decreasing its efficiency by 4% after the fifth cycle, which indicates that the prepared Fe1.85Cu0.15Zr1.85W0.15O7 photocatalyst is a promising novel photocatalyst due to its superior efficiency in dye photodegradation.

Removal of carbol fuchsin from aqueous solution by using three-dimensional porous, economic, and eco-friendly polymer

In this study, a three-dimensional (3D) porous polydimethylsiloxane (PDMS) was prepared using a cheap material with a highly simple and different method. PDMS was firstly applied for the removal of carbol fuchsin (CF) cationic organic dye pollution in this study. Besides, the adsorption capacity of 3D PDMS for removal of the CF was found quite high compared to other materials in already published results. The synthesized PDMS was characterized using several spectroscopic and imaging techniques such as FTIR, Raman, SEM, stereomicroscope, EDX, UV/Vis, and TGA. The optimal conditions were found as 10 mg L^-1 initial concentration, 20 mg of adsorbent dose, 2 h contact time, pH 10, and 25°C temperature. The removal % of CF and the maximum adsorption capacity were calculated at approximately 89% and 88.8 mg g^-1 , respectively. Furthermore, the equilibrium studies showed that the Langmuir isotherm model fitted well with the removal of CF. Moreover, according to the kinetic results, the second-order kinetic model was found suitable (q_e,cal 89.3 mg g^-1 and q_e,exp 88.8 mg g^-1 close to each other) for the adsorption of CF. Also, the thermodynamic studies indicated that adsorption occurs spontaneously, and the adsorption process was physical adsorption. Besides, the reusability of the adsorbent was studied. PRACTITIONER POINTS: Water treatment technology should be low cost, economically viable and in the meantime, eco-friendly. The 3D porous PDMS was prepared by using cheap material with a highly simple method and eco-friendly This unique material was firstly applied for the removal of organic dye in water in this study.