Supercritical fluid extraction and chromatography of aromatic amines

Analysis of low-molar-mass materials in commercial rubber samples by Soxhlet and headspace extractions followed by GC–MS analysis

Very tight regulations apply to materials used for pharmaceutical packaging and for administering drugs. In this paper, we describe a simple and reliable procedure involving both gas- and liquid-phase extraction steps followed by an analysis step to identify the low-molar-mass materials in commercial-rubber samples. Representative commercial rubbers, that could be used for pharmaceutical packaging, have been selected and cryogenically powdered. Headspace and Soxhlet extractions have been carried out and the key parameters are discussed. The obtained extracts have been analyzed by gas chromatography (GC)-mass spectrometry (MS). More than 100 compounds have been detected and identified. Headspace allowed to extract the more-volatile compounds, whereas Soxhlet extraction recovered less-volatile compounds, but induced a loss of the volatile ones. Thus, both extraction techniques are required to fully characterize the low-molar-mass compounds present in rubber.

Determination of adipate plasticizers in poly(vinyl chloride) by microwave-assisted extraction

A new method based on the application of microwave radiation to the extraction of adipate plasticizers from poly(vinyl chloride) PVC plastics is described. The experimental conditions for microwave-assisted extraction (i.e. extracting solvent, temperature, time and microwave power) were evaluated in terms of recovery. The optimisation was carried out with pastes of PVC plastified with di-2-ethylhexyl adipate, and extracts were measured by gas chromatography with flame ionization detection. Six different adipate plasticizers were studied, and microwave-assisted extraction was compared with supercritical fluid extraction for the extraction of adipates and phthalates from PVC matrices. It has been observed that the microwave-assisted extraction parameters evaluated are tightly interconnected. It has been shown that the efficiency of microwave-assisted extraction depends on the kind of solvent, the temperature achieved and the heating time. Moreover, the final temperature reached depends on the microwave power, the number of vessels and the irradiation time. On the other hand, microwave-assisted extraction provides higher recovery values than supercritical fluid extraction for both phthalate and adipate plasticizers.

Harmful azo colorants in leather. Determination based on their cleavage and extraction of corresponding carcinogenic aromatic amines using modern extraction techniques

This study concerns the possibilities of using microwave-assisted extraction (MAE) or supercritical fluid extraction (SFE) for detection of harmful azo colorants in leather. After degreasing of the leather sample with SFE there follows a reductive cleavage of the azo colorants to their corresponding aromatic amines in the MAE or SFE equipment. The aromatic amines are subsequently extracted using either MAE or SFE and then finally determined by liquid chromatography with diode-array detection. The results have been compared with recoveries obtained using the German DIN method 53316. This standard method, based on conventional solvent extraction, is used in several European countries. Overall much better recoveries were obtained using MAE or SFE. With both MAE and SFE the amine recoveries of spiked leather samples were generally above 50%. The average recoveries were 62% for MAE and 60% for SFE (solvent collection) compared to 24% with the DIN method. For genuine leather samples the recoveries decreased, especially for benzidine. In this case the average values for MAE, SFE and DIN were 54, 38 and 19%, respectively. The quantification limits in leather samples using MAE or SFE were below 1 mg/kg for all amines investigated. The within-laboratory precision was generally better than 10%, varying somewhat with the analyte considered. With the proposed methodology, the amount of hazardous organic solvents used could be decreased and the sample throughput increased with at least a factor of two with less manual handling compared to the DIN method.

Analysis of citrates and benzoates used in poly(vinyl chloride) by supercritical fluid extraction and gas chromatography

Supercritical fluid extraction (SFE) has been demonstrated to be a useful tool in the determination of additives in polymeric materials. This paper describes the determination of some citrates and benzoates in poly(vinyl chloride) blended with 33-34% of plasticizer using off-line SFE followed by gas chromatography. Experimental factors affecting SFE have been studied by gravimetric analysis, followed by analysis of the extracts using a gas chromatograph equipped with a flame ionization detector. The extraction process is governed by the solubility of the plasticizers in the supercritical fluid or by their diffusion through the polymer matrix, which depend on the pressure and temperature used. Maximum extraction (>99%) is obtained at pressures and temperatures higher than 40 MPa and 80 degrees C, respectively. Due to purge losses, the collection efficiency of plasticizers into a liquid solvent ranges from 85 to 90%. The applicability of the SFE method is demonstrated using real samples and comparing the results with those obtained by conventional Soxhlet extraction.

Optimization of parameters for the analysis of aromatic amines in finger-paints

A study for the optimisation of the supercritical fluid extraction (SFE) of some aromatic amines (4-chloro-o-toluidine, 2-naphthylamine, 4-aminobiphenyl and benzidine) in finger-paints was conducted. The influence of different variables related to the technique on recoveries was investigated. The analytes were subsequently analysed by gas chromatography after SFE. The study allowed the estimation of four main factors (temperature, pressure, static time and volume of modifier) on recoveries by the use of a two-level factor design, where most significant parameters as well as second- and third-order interactions were identified. Other factors, such as type and volume of modifier and time of contact between the spiker solution and the sample prior to extraction, were also studied. The influence of matrix on extraction recovery was also evaluated by applying the method to different finger-paints, and recoveries were similar or even higher in some cases. The drying process of samples was also studied, while classical drying in an oven and microwaves were compared, with similar efficiencies in both methods. The method was validated by extracting the aromatic amines from some commercial finger-paints.

Determination of some aromatic amines in finger-paints for children's use by supercritical fluid extraction combined with gas chromatography

A test method based on supercritical fluid extraction (SFE) and gas chromatography has been developed for some aromatic amines, such as 4-chloro-o-toluidine, beta-naphthylamine and 4-aminobiphenyl. A two-level factor design was used as the optimization procedure. Four main variables were considered: CO2 pressure, extraction temperature, static extraction time and volume of modifier (methanol). Results obtained for 4-chloro-o-toluidine, indicated that the volume of modifier was the variable with the most important influence on extraction, CO2 pressure had a negative effect and temperature and time were less significant. For the other amines, static time was the most important variable in both cases, followed by CO2 pressure and volume of modifier, with no influence of temperature. SFE was compared with Soxhlet extraction, and was found to give higher recoveries in all cases. Other commercial finger-paints were tested for the presence of aromatic amines.