Membrane potentials of membranes with fixed ionic sites

Backside calibration potentiometry: ion activity measurements with selective supported liquid membranes by calibrating from the inner side of the membrane

In direct potentiometry, the magnitude of the measured potentials is used to determine the composition of the sample. While this places rather formidable demands on the required reproducibility of the associated potential measurements, typically on the order of microvolts, in vitro clinical analyses of blood samples are today successfully performed with direct potentiometry using ion-selective electrodes (ISEs). Unfortunately, most other analytical situations do not permit the sensor to be recalibrated every few minutes, as in environmental monitoring or in vivo measurements, and direct potentiometry is often bound to fail as an accurate method in these circumstances. This paper introduces a novel direction for potentiometric sensing, termed backside calibration potentiometry. Chemical asymmetries across thin supported liquid ISE membranes are assessed by determining the direction of potential drift upon changing the stirring rate on either side of the membrane. Disappearance of this drift indicates the disappearance of concentration gradients across the membrane and is used to determine the sample composition if the solution composition at the backside of the membrane and the interfering ion concentration in the sample are known. For practical determinations, the concentration of either the primary or the interfering ion is varied in the reference solution until the stirring effect disappears. The procedure is demonstrated with a Ca2+-selective membrane using Ba2+ as the dominant interfering ion. Another example includes the determination of Pb2+ in environmental samples where the pH is adjusted to a known level. At pH 4.0, H+ turns out to be the dominant interfering ion. The practical applicability of the method is shown with different environmental water samples, for which the results obtained with the novel method are compared with those obtained by traditional calibration using standard additions. The limitations of the novel method in terms of accuracy and applicable concentration ranges are discussed.

Threshold ionic site concentrations required for Nernstian potentiometric responses of neutral ionophore-incorporated ion-selective liquid membranes

An equation that can describe the concentrations of ionic sites required for a Nernstian potentiometric response slope of neutral ionophore-incorporated ion-selective liquid membranes is presented. This equation is derived from a model based on electrical diffuse layers on both the membrane and the aqueous sides of the interface, in which the phase boundary potential is correlated to the surface charge density as well as the salt concentrations in the bulk membrane and aqueous solution. To experimentally and accurately confirm the validity of this equation, response characteristics of field effect transistors covered by neutral ionophore-based liquid membranes with varying concentrations of a derivative of tetraphenylborate as an anionic site but free of ionic impurities were examined. The observed membrane potentials and the response slopes for membranes with various concentrations of anionic sites were in good agreement with the values calculated from the theory presented in this paper with the measured complexation stability constants for the relevant systems. This result indicates that the theoretical prediction based on the proposed equation for the anionic site concentration is accessible for the preparation of neutral ionophore-incorporated ion-selective liquid membranes, which show Nernstian response slopes for the primary ions.

Producing "self-plasticizing" ion-selective membranes

Polymer membranes have been explored for the analysis of ions that do not require plasticizers and with photocurable properties. This work was focused on investigating the viability of the methacrylic-acrylic copolymers as new self-plasticizing membrane matrixes for ion-selective electrodes or other ion-sensor applications. Copolymers with glass transition temperatures ranging from -20 to -44 degrees C could be prepared without added plasticizer and were found to be functional as ion-selective membranes. Both free-radical solution polymerization and photopolymerization could be used, and "self-plasticizing" behavior of copolymers was observed with a high alkylacrylate (R = C4) content. This was found to be compatible with most commercially available ionophores, and sensors for potassium, sodium, calcium and pH were fabricated entirely by photocure procedures; single-step procedures for the immobilization of benzo-15-crown-5 ionophore on these self-plasticizing copolymer matrixes were also developed. Even though the ionophore was immobilized, potentiometric studies revealed that the ionophore remained functional, and thus, these copolymers have the advantage of suffering neither leaching of ionophore nor plasticizers. All these sensors exhibited a Nernstian or near Nernstian response with selectivity comparable to plasticized PVC membranes or other plasticized and photocurable polymer membranes. The long-term response of the potassium sensor with immobilized ionophore and the sodium sensor showed little deterioration for as long as one month and three months, respectively, under continuous use.