Concatemers in a rapidly sedimenting, replicating bacteriophage T7 DNA

Multidimensional analysis of intracellular bacteriophage T7 DNA: effects of amber mutations in genes 3 and 19

By use of rate-zonal centrifugation, followed by either one- or two-dimensional agarose gel electrophoresis, the forms of intracellular bacteriophage T7 DNA produced by replication, recombination, and packaging have been analyzed. Previous studies had shown that at least some intracellular DNA with sedimentation coefficients between 32S (the S value of mature T7 DNA) and 100S is concatemeric, i.e., linear and longer than mature T7 DNA. The analysis presented here confirmed that most of this DNA is linear, but also revealed a significant amount of circular DNA. The data suggest that these circles are produced during DNA packaging. It is proposed that circles are produced after a capsid has bound two sequential genomes in a concatemer. The size distribution of the linear, concatemeric DNA had peaks at the positions of dimeric and trimeric concatemers. Restriction endonuclease analysis revealed that most of the mature T7 DNA subunits of concatemers were joined left end to right end. However, these data also suggest that a comparatively small amount of left-end to left-end joining occurs, possibly by blunt-end ligation. A replicating form of T7 DNA that had an S value greater than 100 (100S+ DNA) was also found to contain concatemers. However, some of the 100S+ DNA, probably the most branched component, remained associated with the origin after agarose gel electrophoresis. It has been found that T7 protein 19, known to be required for DNA packaging, was also required to prevent loss, probably by nucleolytic degradation, of the right end of all forms of intracellular T7 DNA. T7 gene 3 endonuclease, whose activity is required for both recombination of T7 DNA and degradation of host DNA, was required for the formation of the 32S to 100S molecules that behaved as concatemers during gel electrophoresis. In the absence of gene 3 endonuclease, the primary accumulation product was origin-associated 100S+ DNA with properties that suggest the accumulation of branches, primarily at the left end of mature DNA subunits within the 100S+ DNA.

Comparison of the physical properties and assembly pathways of the related bacteriophages T7, T3 and phi II

To understand constraints on the evolution of bacteriophage assembly, the structures, electrophoretic mobilities (mu) and assembly pathways of the related double-stranded DNA bacteriophages T7, T3 and phi II, have been compared. The characteristics of the following T7, T3 and phi II capsids in these assembly pathways have also been compared: (1) a DNA-free procapsid (capsid I) that packages DNA during assembly; (b) a DNA packaging-associated conversion product of capsid I (capsid II). The molecular weights of the T3 and phi II genomes were 25.2 X 10(6) and 25.9 (+/- 0.2) X 10(6) (26.44 X 10(6) for T7, as previously determined), as determined by agarose gel electrophoresis of intact genomes. The radii of T7, T3 and phi II bacteriophages were indistinguishable by sieving during agarose gel electrophoresis (+/- 4%) and measurement of the bacteriophage hydration (+/- 2%) (30.1 nm for T7, as previously determined). Assuming a T = 7 icosahedral lattice for the arrangement of the major capsid subunits (p10A) of T7, T3 and phi II best explains these data and data previously obtained for T7. At pH 7.4 and an ionic strength of 1.2, the solid-support-free mu values (mu 0 values) of T7, T3 and phi II bacteriophages, obtained by extrapolation of mu during agarose gel electrophoresis to an agarose concentration of 0 and correction for electro-osmosis, were -0.71, -0.91 and -1.17(X 10(-4) cm2V-1 s-1. The mu 0 values of T7, T3 and phi II capsids I were -1.51, -1.58 and -2.07(X 10(-4] cm2V-1 s-1. For the capsids II, these mu 0 values were -0.82, -1.07 and -1.37(X 10(-4] cm2V-1 s-1. The tails of all three bacteriophages were positively charged and the capsid envelopes (heads) were negatively charged. In all cases the procapsid had a negative mu 0 value larger in magnitude than the negative mu 0 value for bacteriophage or capsid II. A trypsin-sensitive region in capsid I-associated, but not capsid II-associated, T3 p10A was observed (previously observed for T7). The largest fragment of trypsinized capsid I-associated p10A had the same molecular weight in T7 and T3, although the T3 p10A is 18% more massive than the T7 p10A. It is suggested that the trypsin-resistant region of capsid I-associated p10A determines the radius of the bacteriophage capsid.