Interaction of naproxen with ß-cyclodextrin in ground mixture

Comparison of the Conventional and Mechanochemical Syntheses of Cyclodextrin Derivatives

Many scientists are working hard to find green alternatives to classical synthetic methods. Today, state-of-the-art ultrasonic and grinding techniques already drive the production of organic compounds on an industrial scale. The physicochemical and chemical behavior of cyclodextrins often differs from the typical properties of classic organic compounds and carbohydrates. The usually poor solubility and complexing properties of cyclodextrins can require special techniques. By eliminating or reducing the amount of solvent needed, green alternatives can reform classical synthetic methods, making them attractive for environmentally friendly production and the circular economy. The lack of energy-intensive synthetic and purification steps could transform currently inefficient processes into feasible methods. Mechanochemical reaction mechanisms are generally different from normal solution-chemistry mechanisms. The absence of a solvent and the presence of very high local temperatures for microseconds facilitate the synthesis of cyclodextrin derivatives that are impossible or difficult to produce under classical solution-chemistry conditions. Although mechanochemistry does not provide a general solution to all problems, several good examples show that this new technology can open up efficient synthetic pathways.

Toward a Greener World-Cyclodextrin Derivatization by Mechanochemistry

Cyclodextrin (CD) derivatives are a challenge, mainly due to solubility problems. In many cases, the synthesis of CD derivatives requires high-boiling solvents, whereas the product isolation from the aqueous methods often requires energy-intensive processes. Complex formation faces similar challenges in that it involves interacting materials with conflicting properties. However, many authors also refer to the formation of non-covalent bonds, such as the formation of inclusion complexes or metal–organic networks, as reactions or synthesis, which makes it difficult to classify the technical papers. In many cases, the solubility of both the starting material and the product in the same solvent differs significantly. The sweetest point of mechanochemistry is the reduced demand or complete elimination of solvents from the synthesis. The lack of solvents can make syntheses more economical and greener. The limited molecular movements in solid-state allow the preparation of CD derivatives, which are difficult to produce under solvent reaction conditions. A mechanochemical reaction generally has a higher reagent utilization rate. When the reaction yields a good guest co-product, solvent-free conditions can be slower than in solution conditions. Regioselective syntheses of per-6-amino and alkylthio-CD derivatives or insoluble cyclodextrin polymers and nanosponges are good examples of what a greener technology can offer through solvent-free reaction conditions. In the case of thiolated CD derivatives, the absence of solvents results in significant suppression of the thiol group oxidation, too. The insoluble polymer synthesis is also more efficient when using the same molar ratio of the reagents as the solution reaction. Solid reactants not only reduce the chance of hydrolysis of multifunctional reactants or side reactions, but the spatial proximity of macrocycles also reduces the length of the spacing formed by the crosslinker. The structure of insoluble polymers of the mechanochemical reactions generally is more compact, with fewer and shorter hydrophilic arms than the products of the solution reactions.

Enhancement of Dehydroepiandrosterone Solubility and Bioavailability by Ternary Complexation with α‐Cyclodextrin and Glycine

In the present work we investigated the possibility of improving dehydroepiandrosterone (DHEA) solubility and bioavailability by high-energy cogrinding with alpha-cyclodextrin (alpha-Cd) in the presence or absence of different auxiliary substances (glycine, biomaltodextrin, poly(vinyl pyrrolidone), poly(ethylene glycol) 400). In all cases, ternary products exhibited higher drug solubilizing properties than the binary DHEA-alpha-Cd coground system. Glycine was the most effective component. The best combinations, corresponding to 1:1:2 and 1:2:3 drug-alpha-Cd-glycine molar ratios, were characterized by differential scanning calorimetry and X-ray powder diffractometry and evaluated for dissolution rate. The presence of glycine favored destruction of DHEA crystalline structure during cogrinding, as evidenced by the strong reduction in both time and vibration frequency of milling necessary to obtain total drug amorphization. Both ternary products showed better dissolution properties than the drug alone, affording, respectively, a 40 and 60% increase of dissolution efficiency. The 1:2:3 coground product was then selected for in vivo bioavailability studies in women suffering from adrenocortical insufficiency. DHEA and DHEA sulfate blood levels were significantly higher (p < 0.001) after oral administration of the coground product than after oral administration of untreated drug, with a 100% increase in the area under the curve (AUC) of concentration versus time. Moreover, the time to reach maximum concentration (t(max)) decreased from 2.2 with the untreated drug to 0.5 h with the coground product, and the mean permanence time of DHEA within physiological levels was four times longer for the coground product compared with the untreated drug. These results indicate that the developed product is particularly suitable for oral DHEA formulations in hormone replacement therapies.

Effects of grinding with microcrystalline cellulose and cyclodextrins on the ketoprofen physicochemical properties

Ground mixtures of ketoprofen (KETO) with native crystalline beta-cyclodextrin, amorphous statistically substituted methyl-beta-cyclodextrin, and microcrystalline cellulose were investigated for both solid phase characterization (differential scanning calorimetry (DSC) powder X-ray diffractometry, and infrared (IR) spectrometry) and dissolution properties (dispersed amount and rotating disk methods) to evaluate the role of the carrier on the performance of the final product. The effects of different grinding conditions, partial sample dehydration, and 1 year storage at room temperature were also investigated. The results pointed out the importance of the carrier nature on the efficiency of the cogrinding process. Both cyclodextrins were much more effective than was microcrystalline cellulose, even though no true inclusion complex formation occurred by mechanochemical activation. The best results were obtained from ground mixtures with methyl-beta-cyclodextrin, which showed the best amorphizing and solubilizing power toward the drug and permitted an increase of approximately 100 times its intrinsic dissolution rate constant, in comparison with the approximate 10 times increase obtained from ground mixtures with beta-cyclodextrin.

Solubilization and interaction of sulindac with beta-cyclodextrin in the solid state and in aqueous solution

A sulindac-beta-cyclodextrin complex was obtained by the coprecipitation method. Kneaded solids and physical mixtures were also prepared. The complex was shown by x-ray powder diffraction to be noncrystalline whereas pure drug and any of the other sulindac-beta-CD system were crystalline. the endothermic peak of sulindac due to the fusion of drug disappeared in DSC thermograms for the coprecipitate product, which confirmed the interaction between sulindac and beta-CD in the solid state. After a 1-year storage drug crystals could not be observed by x-ray diffractometry, which indicated that the complex formed was stable. The complex showed the fastest dissolution rate which might be attributed to the high-energy noncrystalline state and the inclusion complex formation in solution. UV spectra were modified and the apparent solubility of the drug increased with the addition of beta-CD, which confirmed the interaction between sulindac and the ligand in solution. The apparent stability constant, K1:1, for the complex at pH 2 and 25, 30, and 37 degrees C was 340, 220, and 160 M-1, respectively, which confirmed the influence of temperature on the complex stability. The value of K1:1 at pH 6 and 25 degrees C was 139 M-1, which indicated that the complex is formed easier with the non-ionized sulindac. The enthalpy change, delta H degree, showed that the binding process is exothermic.