Interactions between recrystallization and precipitation in hot-deformed microalloyed steels

The Effect of Adding V and Nb Microalloy Elements on the Bake Hardening Properties of ULC Steel before and after Annealing

Bake hardening (BH) is a vital part of special steel production. Studies in this field have focused on steels under homogeneous yielding, but until now, none have been conducted on the phenomena that occur for steels under heterogeneous yielding. In the current study, the effect of adding Nb and V alloying elements on the strength of ultra-low carbon (ULC) steel after bake hardening was investigated. The effects of pre-strain, grain size, and recrystallization annealing temperature were analyzed, as well as the effect of Nb and V on the yield stress caused by the bake hardening process. For this purpose, five types of alloys with different V and Nb contents were melted, cast in an induction furnace, and subjected to hot hammering and hot rolling. Then, cold rolling was applied to the samples by ~80%. To eliminate the effects of cold working, tensile samples were subjected to recrystallization annealing at 750 and 800 °C for 30 min, and the samples were quickly quenched in a mixture of a NaCl solution and ice. The annealed samples were subjected to a pre-tensile strain in the range of 2-12% and then aged in a silicone oil bath at 180 °C for 30 min. Then they were subjected to a tensile test. The obtained results showed that with the increase of the pre-strain and the annealing temperature, the values of baking hardness increased. The presence of V in the composition of steel reduced the annealing temperature.

Interaction between Microalloying Additions and Phase Transformation during Intercritical Deformation in Low Carbon Steels

Heavy gauge line pipe and structural steel plate materials are often rolled in the two-phase region for strength reasons. However, strength and toughness show opposite trends, and the exact effect of each rolling process parameter remains unclear. Even though intercritical rolling has been widely studied, the specific mechanisms that act when different microalloying elements are added remain unclear. To investigate this further, laboratory thermomechanical simulations reproducing intercritical rolling conditions were performed in plain low carbon and NbV-microalloyed steels. Based on a previously developed procedure using electron backscattered diffraction (EBSD), the discretization between intercritically deformed ferrite and new ferrite grains formed after deformation was extended to microalloyed steels. The austenite conditioning before intercritical deformation in the Nb-bearing steel affects the balance of final precipitates by modifying the size distributions and origin of the Nb (C, N). This fact could modify the substructure in the intercritically deformed grains. A simple transformation model is proposed to predict average grain sizes under intercritical deformation conditions.

Control of Upstream Austenite Grain Coarsening during the Thin-Slab Cast Direct-Rolling (TSCDR) Process

Thin-slab cast direct-rolling (TSCDR) has become a major process for flat-rolled production. However, the elimination of slab reheating and limited number of thermomechanical deformation passes leave fewer opportunities for austenite grain refinement, resulting in some large grains persisting in the final microstructure. In order to achieve excellent ductile to brittle transition temperature (DBTT) and drop weight tear test (DWTT) properties in thicker gauge high-strength low-alloy products, it is necessary to control austenite grain coarsening prior to the onset of thermomechanical processing. This contribution proposes a suite of methods to refine the austenite grain from both theoretical and practical perspectives, including: increasing cooling rate during casting, liquid core reduction, increasing austenite nucleation sites during the delta-ferrite to austenite phase transformation, controlling holding furnace temperature and time to avoid austenite coarsening, and producing a new alloy with two-phase pinning to arrest grain coarsening. These methodologies can not only refine austenite grain size in the slab center, but also improve the slab homogeneity.

New Technology to Produce 1 GPa Low Carbon Microalloyed Steels from Cast Strip

Global economy requires steel with further increasing mechanical properties and simultaneously decreasing price. In mass manufacturing three major methods can be used to increase strength: (i) increase microalloying element additions (increases cost), (ii) decrease deformation temperature and (iii) increase cooling rate after high temperature processing (both can be challenging for equipment). Thin strip casting is an effective way to reduce cost as it brings a reduction in number of deformation passes and shortens the production line. However, the mechanical properties can be missed due to insufficient microstructure development. In this article, we investigate a recently proposed technology based on Austenite Conditioning followed by Accelerated Cooling and Warm Deformation (AC2WD). Two low carbon steels microalloyed with either 0.012Ti or 0.1Mo-0.064Nb-0.021Ti (wt.%) were subjected to three processing modifications of the AC2WD-technology with two, one or no deformation of cast microstructure in the austenite temperature field. The Ti- and MoNbTi-steels exhibited 685–765 MPa and 880–950 MPa of the yield stress, 780–840 MPa and 1035–1120 MPa of tensile strength, and 20–30% and 22–24% of elongation to failure, respectively. The nature of strengthening mechanisms associated with the AC2WD-technology is discussed on the basis of detailed microstructure characterisation.

Vanadium Microalloyed Steel for Thin Slab Casting and Direct Rolling

Vanadium microalloyed steels with high yield strength (»600MPa), good toughness and ductility have been successfully produced in commercial thin slab casting plants employing direct rolling after casting. Because of the high solubility of VN and VC, most of the vanadium is likely to remain in solution during casting, equalisation and rolling. While some vanadium is precipitated in austenite as cuboids and pins the grain boundaries, a major fraction is available for dispersion strengthening of ferrite. Despite a coarse as-cast grain size, significant grain refinement can be achieved by repeated recrystallisation during hot rolling. Consequently, a fine and uniform ferrite grain structure is produced in the final strip. Increasing the V and N levels increases dispersion strengthening which occurs together with a finer ferrite grain size. The addition of titanium to a vanadium containing steel, decreases the yield strength due to the formation of V-Ti(N) particles in austenite during both casting and equalisation. These large particles reduced the amount of V and N available for subsequent precipitation of fine (~5nm) V rich dispersion strengthening particles in ferrite.